Having problems with your Karcher 1750 psi Electric Pressure Washer ?

I have a craftsman 3000psi and it keeps losing pressure

\015 I would be pressure cleaning for about one min and than it would lose pressure. if you can with this it would help save my nerves. thank you.\015

Answers :

Hi there,
\015\012 this means no water pressure coming
\015\012to pressure tank it was consumed when use for cleaning, the water pump does not work,check water pump if function,if there over load reset,or had to jumper the connection of pressure switch.
\015\012jump the connection of pressure switch,by passing pressure switch if the motor run just jug for 3 seconds,if run you have defefctive pressure switch,replace pressure switch.have a nice day and rate me if your satisfied to my solution,thank's
Repair Help & Product Troubleshooting for Karcher 1750 psi Electric Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a craftsman 3000psi and it keeps losing pressure


Hi there,\015\012 this means no water pressure coming\015\012to pressure tank it was consumed when use for cleaning, the water pump does not work,check water pump if function,if there over load reset,or had to jumper the connection of ... Karcher 1750 psi Electric Pressure Washer

My 3.99 Karcher pressure cleaner seems to keep going on,off,on,off when i release the trigger.It used to keep going momentarly when the trigger was released until the pressure built up,then cut off until the trigger was pressed .Now it goes on ,off,on,off and has decreased pressure.


Hi! robcarrollDid you purge the air from the pump before starting the motor.InMrFixIt ... Karcher 2500 PSI Pressure Washer

Karcher K3.86 doesn't seem to be able to sustain pressure. Keeps trying to pressurize then stops. Only keeps pressure while I spray. SOmestimes it totally shuts down, I guess when it overheats.


Probably water flow check filter going into pump there is anut coming out on an angle going into the pump wire gause filter inside if this is clean follow it back to water supply symptoms definately indicate lack of water youdoit ... Pressure Washers

1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa...


If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of yo ... Karcher 1750 psi Electric Pressure Washer

Pump loses pressure after you use it a while even when trigger is never lifted . i can start it up it runs good trigger pulled and then it loses pressure no cavatation


Looks like you need a new diaphpragm in the pump unit ... Northstar Pressure Washer 3000 PSI

Pressure washer gradually loses pressure


... Psi PowerBoss 20262 Pressure Washer

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

Residential Well Pressure Tank. The tank loses pressure over the course of a year or two and the cycle starts to shorten up. What is the appropriate pressure range for the tank. Should I shut off the water and drain down to get a "true" static pressure when I add air? Sorry about the category. No plumbing category listed.


Yes you drain it down to check the pressure and leave it down till you get it up to around 40 pounds for most applications. ... Dishwashers

Honda black max 2600 psi pressure washer loses pressure


... Honda Black Max 2600 PSI Pressure Washer

I have a karcher 3.80 md electric pressure washer that keeps running when not in use and the pressure is low. Any help please?


... Pressure Washers

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

Have a Husky Pressure Washer 2200 psi, HU80931. I don't have an owner manual. It has set for about a year. When I started the washer there was very little pressure. Did some cleaning and it was a little better, but now there is no pressure and I am having trouble keeping it started. Can you help? The washer was purchased at Home Depot and it has Briggs and Stratton the the washer too. Thank You, RJ


Look at eReplacementParts.com and the parts diagrams ... Briggs & Stratton Pressure Washers

Water is leaking from inside the pump and i see no damaged plastic from the outside.the motor keeps on even after i release the pressure gun and most of all ther is no or less pressure when i trigger the pressure gun.please can you suggest what parts do i have to change for it to be fixed 10x


Hello. The internal seals need to be replaced. Obtain the Karcher rebuild kit I got from pressureparts.com\015\012 \015\012J. ... Karcher Quick Connect Nozzle Set

Hy; I have a karcher 580 I had to replace gun complete so I bough a simoniz xe01-001 at simoniz.osirus.ca/ for your info 69$ complete ***.I install NOW I get pulse up & down ONLY when trigger is press I turn valve down i only get 10% of pressure if i turn valve up that is when it start pulsing pressure up & down it wont keep pressure up ... Bob...


Most likely problem is that the tip is too small causing Unloader to bypass or restriction/debris in tip. Install clean tip of proper size or 1/2 size larger (example from 2.5 gpm to 3 gpm ) to prevent slow pulse. If tip is clean and /o ... Karcher 2500 PSI Pressure Washer

Our pressure washer loses pressure for no reason and it pulses. the water pressure is fine.


Your bypass valve that keeps pressure off the hose when the trigger isn't depressed is stuck open,and not letting the pump build pressure ... Pressure Washers

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

I have an Excell 2500 psi with Briggs & Stratton 6.5 HP engine that starts, builds pressure and maintains high pressure as long as the hose is not connected. But as as soon as I connect the hose, it loses all pressure. Is it the pump?


... Pressure Washers

Pressure washer keeps blowing out a high pressure O-ring


... Pressure Washers

K2300G Karcher Pressure Washer losing water pressure


... Karcher 2500 PSI Pressure Washer

Landa pressure washer LT 4035-4000 psi. Why is it losing pressure and continually pulsating?


If the pump is pulsating rapidly most likely valves are leaking or debris under valve keeping one or more from closing. If the pump pulsates slowly, comes up to pressure then low pressure then repeats, problem is pressure regulator /bypass. Or you ... Pressure Washers

Losing pressure more and more often, especially


Not quite sure where to get the parts, but if the pressure starts out ok and decreases as it runs, it is generally that the piston rings/seals are worn out, this can happen just from sitting up over the winter.You can google Honda Pressur ... Honda Pressure Washers

Briggs & Stratton 2500 Power Washer Loses Pressure Time to Time


If by "a few minutes" you mean 180 seconds, I really don't know what to say. But if you mean 5-10 seconds, you probably are experiencing air in the water line or normal engine warm-up behavior when the choke has been set to full lean too soon. ... Briggs & Stratton 020324 3700 PSI Pro Series Pressure Washer

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Cycle interupted until pressure applied to door, near control panel. Fault is intermittent. Sometimes I need to lean a chair against it to keep it going. Door clicks shut nicely and does not leak. Cycle always starts but often will not complete without a thump. Is pressure inside bowing the door and activating a safety switch?


Problem on the safety switch\015\0121)try to adjust the safety switch to contact properly with the door.\015\0122)any screw is there on switch means loosen the screw &adjust to contact with door. ... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

I have a 3000 psi and it has no more pressure. I took the perssure control knob off and had a look inside there and found pits on that seal on the inside will this make it lose pressure and where do I find kits


Behind the pressure control knob is a releif valve, take it out, put some oring grease around the orings, place back in. make shure you put it all the way down and it seats back in then try again. failing that a small pebble might be stuck under a va ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0765 seconds