Having problems with your Karcher 1750 psi Electric Pressure Washer ?

My Karcher 1750 psi electric pressure washer is making in/out loud noise when switch to On and idling not pressing washer trigger.


Answers :

Thats normal, it is reducing the built up pressure that is not needed until the trigger is pulled.
Repair Help & Product Troubleshooting for Karcher 1750 psi Electric Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Karcher 1750 psi electric pressure washer is making in/out loud noise when switch to On and idling not pressing washer trigger.


Thats normal, it is reducing the built up pressure that is not needed until the trigger is pulled. ... Karcher 1750 psi Electric Pressure Washer

Karcher K3.92 M 1750 PSI poweer Washer motor won't start. Followed Reset/Test/Reset sequence with cord plugged directly into outlet. Light on cord near Reset comes on when Reset pressed down but goes off when Reset released (Normal?) Switch ON and trigger pressed releases water stream but no motor action.


They are sensitive to large extention cords. My father in laws pops reset when a small cord is used. If internally shorted- motor will continually pop the reset even plugged direct to outlet. Check voltage at outlet. ... Karcher 2500 PSI Pressure Washer

Loud repeating noise until the water trigger is pressed


Check the pressure washer for leaks. That sound is probably the unloader valve recycling as the machine slowly looses pressure and needs to build it up again to max pressure. ... Pressure Washers

My washer makes a loud pulsing noise when not being used,as soon as I pull the trigger it works fine.


Sounds like your unit has a bypass problem either needs adjustment or replaced ... Karcher Pressure Washers

Hi ive got a honda gc135 4.0 pressure washer it runs fine but when i release trigger it makes a realy bad noise but when i press the trigger the noise goes i was told it might be the pressure releif valve is this right or is there some thing else wrong with it


... Simpson WS4050V Water Shotgun 4000 Psi Cold Water Electric Start Gas Powered Pressure Washer W/ Vanguard Engine

When I switch my karcher k4.97 washer on it just sits and pulsates(on off on off etc.)When I squeeze the trigger it runs perfect,Then when I release the trigger it reverts back to pulsating.It leaks water when sitting idle.


Well, first the easy bit... the pulsation is caused by the leak, because the machine can't hold pressure when the trigger is released.  The difficult bit is: what to do about it?  Unfortunately, there are several different places where the ... Karcher Pressure Washers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

My Honda VR 2522 on Excell 2500 psi pressure washer run good when in use but when i release the trigger on the wand the motor idles and begans to pulsate, hit and low. Where to i start looking to repair. I have a new air filer installed Roy


... Karcher 2500 PSI Pressure Washer

My new Karcher K2.900 pressure washer trips electrics when I switch on or sometimes when I press trigger Can you help me please Maurice Peak


Sounds like power cable broken check all of it you might need to replace it ... Karcher Pressure Washers

My 1750 psi campbell hausfeld pressure washer will operate at first until I release the trigger on the wand. Then it won't restart. If I wait for a while it will run again. Sounds like the pressure switch.


Common with that washer...it has a wabble pump. Release the trigger, if by pass does not engage, stalls engine. You can however keep using it, all you have to do is keep trigger pressed, and when you are cranking engine, depress trigger with the fr ... Pressure Washers

Have a karcher 1750 psi pressure washer. when you turn the on switch on the motor pulses instead of asteady motor sound. when squeezing trigger it sounds fine. can it be the unloader?


... Karcher 1750 Psi Elec Pressure Washer

I have a karcher 7.85 jet washer that has been unused for a while and now fails to work. I have checked plug fuse and replaced the on off switch and condenser as advised previously however there is no life from the motor at all. When the lance trigger is pressed water does flow however this is minimal.


... Karcher Pressure Washers

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not much. This happened after i ran water out of trigger gun with no lance attached, machine switched on. Seems to leak from trigger handle aswell. Many thanks in advance


This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump. ... Pressure Washers

I have a bosch 110 plus pressure washer the problem i have is i turn on washer squeeze trigger and works fine when i release trigger and press again it wont work and trigger seems to have pressure on it


... Bosch AQUATAK 110 Pressure Washer

Loud noise when I start the dish washer it fills with water and as soon as t starts to run it makes a real loud grinding noise can you tell me what it might be and a rought estimate as to what it might cost to get it fixed. Thanks in advance Jim


My Dishwasher had the same loud Grinding Noise.It was a piece of a plastic fork lodged behind the macerator blade. This is at the suction to the pump just under the strainer. check this out first before you pull everything apart. You s ... Maytag MDB7100AWB Dishwasher

Pressure washer start fine and idles appropriately trigger is depressed washer runs for about five minutes then just shuts off. Engine restarts fine but when trigger is depressed engine shuts off


Looks like the fuel cap may not be venting try it with the cap loose allowing air into the tank sounds like lack of fuel entering into the carburetor. ... Karcher 2500 PSI Pressure Washer

My Troy Bilt pressure washer (Model: 020296-01) idle is up and down. When I engage the trigger I get pressure for a second and that's it. If I squeeze the trigger a second later I get the same thing and so on. Is it just the idle that needs to be adjusted or something else?


... Briggs & Stratton Pressure Washers

I have a DPH3800 Dewalt pressure washer and the soaper isn't working properly. Right tip is being used but when trigger is not pressed it puts water into the bucket. When trigger is pressed it does **** some solution into the hose but very little and very slow. The valve is opened all the way. I know my former partner used bleach in the system which I read in the manual is a no no but it did work at the end of last season. Any ideas?


How is the pump connected on a john deere 3800 psi. i took out the 4 bolts and drained the oil. pump is stuck to cam. how does it come off? ... Dewalt 3800 PSI Pressure Washer

Kenmore dishwasher has loud noise during fill. If you let it go, the washer fills. Once filled, noise stops and wash cycle continues. Sounds like plumbing does when there is air in the pipes. Not a grinding sound. Very deep pitch. Stops when the washer fills with water.


This isn't a solution but rather a comment, if the problem is happening only during the fill, then it could be the water inlet valve. Perhaps there is a soliniod going in the valve, watch to see if the fill cycle starts to dimminish over time. Does t ... Kenmore Dishwashers

When i started the washer and pressed the trigger the first time i had good preasure but when i released the trigger and pressed it again i have no preasure


Hi:This sounds like the bypass valve is stuck. You need to get at it and pull it out. Then check it for o-ring damage and be sure you lube it with a good waterproof grease before replacing. If ... Karcher 2500 PSI Pressure Washer

If i switch on my dishwasher, all lights flash on and off red,and it's makes the beeping noise when it does when the wash is finished... no water is coming in either... please help... it does nothing and you cannot press any of the buttons to use a cycle. it is making a humming noise. i have checked the filter in the bottom of it, and have switched it off at the wall and back on again. cheers,


Un plug it remove bottom drawer. look in back left corner of cabnet on bottom, is it wet dry it out and try again ... Fisher and Paykel Dishwashers

Made funny noise; stopped to investigate; then wouldn't restart; followed directions below from FixYa and restarted. It finished the cycle, apparently correctly, except it left a little water in the tub. Also, continued to make a lot of noise--a loud motor hum/buzz or similar. Did not make this noise during dry cycle. Dishwasher is Kenmore Model 665; stock number 16839. Can you give continued diagnostic instructions? Appears there is a cracked washer under the lower wand assembly; th


The solution was nearly correct. The person who answered only forgot to mention that water level and pressure switch must be tested. This can cause drain pump working longer than necessary and humming, and machine underfilling, which can cause noise ... Dishwashers

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0860 seconds