Having problems with your Karcher 2500 PSI Pressure Washer ?

Water in oil

\015 I have a karcher HD3000G and had a "Service Tech" install a new kit in the pump but now it will not build preasure and it has water in the oil.\015

Answers :

Dear akwelectrica,
\015\012When a full kit was installed....WHAT was installed??? Were the OIl seals replaced?? Were the Low Pessure Seals Replaced?? Were the high Pressure Seals Replaced?? Was the OIL changed?? If the oil was changed...did all water in the oil compartment been removed?? Also did the suction and delivery valves were replaced?? Now if all these things were done, BUT the pistons were not changed, than the whole kit was done for nothing!! My suspicion is that the PISTONS were not changed. But if all the kit was used and even the PISTONS were changed, than you must for sure have a cracked or damaged head. When I say the HEAD...I am always refering to the part that holds the pistons. But in rare circumstances even the outer head could be damaged. Ask your "Service Tech" what he replaced and you will know the answear. As I said..I suspect that the PISTONS were not replaced by New Ones.
Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lack of pressure in a karcher 455. motor powers on changes sound as trigger is depressed but water remains at mains pressure. oil replaced and had no water in old oil. any ideas.

Most cases the engine is used on many different units find one of those for a pump ... Karcher 4.550-620.0 pressure washer part 45506200/4.550-620.0

My problem with Karcher K2-59M is doesn't switch off when releasing spray trigger and it leaks water from two small holes in water inlet tube. I have stripped the washer down but find no solution. Also some oil has been lost how does one replace the oil?

These units normally use a flow switch which actually feeds the pump motor failure to shut down causes overpressurization in pump head causing pump failure oil is normally sealed replacing the oil, pump has to be separated from motor and possible sea ... Pressure Washers

I just purchased a RMV2.5G27D Universal pump. Installation was easy, but I have two questions. 1. No where in the booklet does it say to put oil in it, does it come with oil already inside? There was no oil in the box but the instructions kept refering to 2.2 ounces of oil. 2. It had a red plastic plug opposite the water intake, included was a brass plug that fits into that area, does the plastic plug stay or do I put the brass plug in it?

The red plastic plug comes off, that is the plug that is only used for shipping. You should have got a ventable oil plug to replace that one in the box. The oil you would need is this ... Annovi Reverberi RMV2.5G27D Pressure Washer Pump

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.

I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

Karcher 6.85 replaced seals as they were worn out and passing water into the oil now when I turn it on motor runs turning water on water comes out of outlet (which is ok??) but does not pressurize with hose disconnected. My Bosch pressure cleaner passes water through but when pump is started it pressurizes. Is it bypassing? Thanks in advanced

... Pressure Washers

Changing oil on a high pressure washer with Comet Water Pump

... Comet BXD2527 Pressure Washer Pump

Water flows from pump head continously and the last time I used it oil was all over pump.is this normal ? The washer is northstar,gas driven and is not to old. the water comes from two openings in the bottom of the brass head plate.

... Pressure Washers

DP3750 / 4GPM - Pump oil was milky. Drained, washed out & refilled w/ pump oil. No pressure and spewing water out the soap siphon inlet.

Thats the water in the oil! it means that gasket dos not hold the preshe. ... Dewalt Pressure Washers

Honda Trash Pump Model WT30X Stalling - 8hp engine runs for approx 5 seconds that shuts down, restarts after I hear a relay click ? oil is fine - so I do not believe that it is an oil pressure sensor. Are there any other sensors ? Does water have to be pumping through it??

Their is an oil level sensor that lasts around 3 months of use. unplugging it would solve your problem But replacing it is a night mare. and if your oil runs out It's all over. if not the oil sensor, and your spark is constant Check your fuel system ... Honda 8 HP Engine

My AR pressure washer pump is not spraying water out the wand. I noticed on the top oil cap is squirting oil out of the tiny hole. Please help

... Pressure Washers

Oil and water comming out of oil filler stem

You have a seal on the pump between the pump and the water pump thats leaking you have oil and water mixing . I owen three mechines and i don't understand what you mean when you say the oil filler stem. I also rebuild power washers and pumps. If you ... Comet BXD2527 Pressure Washer Pump

I have an excel pressure washer 11 hp Honda engine. water is leaking into the cat pump 4hp40gl causing the oil to become milky, after the washer sits overnight the oil clears up. Any and all help will be appreciated. Thanks

... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

Replaceing a water pump in a 2003 frieghtliner with a 3126 cat. have water pump loose from engine but will not come completely off. Does the oil cooler or the front accessory bracket need to be removed to get pump off?

... Caterpillar CAT Pump Pressure Washer Pump Oil

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.

... Pressure Washers

Starts but does not keep running. checked oil & its full. do you need water pressure at the pump? I know it has a low oil pressure cut off.

First: check and change the spark plug and do a oil change (OIL IS NOT THE PROBLEM BUT IS GOOD TO DO IT) then do a test with fresh gasoline.\012Second:check all fuel components (LINES,CARB,ETC...)\012Third:if any of this fix the problem ... Dewalt DPD3100 Gas Pressure Washer

Hi I have a karcher 2020b. When power is on it sounds like it is on... When I press the trigger almost no water comes out. When this happened unnoticed oil on the floor afterwards. I have cleaned the filter, the nozzle and flushed the water through to get rid of a possible air lock to no avail. It also smelt slightly of burning plastic - any help would be appreciated. Thanks

... Pressure Washers

I cant get water to spray from my pressure. the oil cap is throwing oil out the little hole. no pressure is coming out of the nozle. AR. model#SJV 2.5G27-1

... Annovi Reverberi RMV2.5G27D Pressure Washer Pump

The oil in my gc160 Honda pressure washer is getting water in it some how. Could it be something with the water pump gasket or what? And I can get it started but can't keep it running un less I keep spraying starter fluid in the carbar. Please help ?

... Karcher 2500 PSI Pressure Washer

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?

If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

Comet tw 5050 mix oil and water

What you have is a bad seal or a crack within the pump crack more common if any water was left in it during the cold winter ... Comet Pressure Washer Tw5050 Triplex Pump 5000 Psi Fits 24 Hp Motors

Water leaking from oil burner relief valve, pressure limit switch adjustment?

... Dishwashers

What oil do i use for my wolf pressure washer water pupm

... Pressure Washers

Pressure washer is getting water in oil

... Pressure Washers

Oil is mixing with water in transmission

You need to reseal the pump but look for cracks it might have froze during the winter ... Campbell Hausfeld Pressure Washers

Water in oil

Dear akwelectrica,\015\012When a full kit was installed....WHAT was installed??? Were the OIl seals replaced?? Were the Low Pessure Seals Replaced?? Were the high Pressure Seals Replaced?? Was the OIL changed?? If the oil was changed...did ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0999 seconds