Having problems with your Karcher 2500 PSI Pressure Washer ?

Removing unloader valve

\015 Karcher K2400 HH. After removing the (2) screws and spring, what do you use to grab the unloading valve to pull it out?\015\012****\015

Answers :

You can hook it up to the water supply but many times you are going to have to start the unit up to get the unloader to come out. I would recommend putting something over the top of the pump so when it comes out you don't lose a eye. If you still have an issue with it not coming out you are going to have to pour some white vinagur down the cylinder and let it sit for a couple hours, this will breakdown any build-up inside the cylinder.
If you can't get it out with needle nose pilers try turning the garden hose pressure on and the water should pop it out.
Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Karcher pressure washer unloader valve sticking? I have the pump shown on page 3 of Karcher manual number 91392030. I removed the unloader valve, but am not sure if I have the entire assembly. I got the top seal and a spring. The bottom seal may be jammed in the pump.


... Karcher G3025OH Pressure Washer

Removing unloader valve


You can hook it up to the water supply but many times you are going to have to start the unit up to get the unloader to come out. I would recommend putting something over the top of the pump so when it comes out you don't lose a eye. If you still hav ... Karcher 2500 PSI Pressure Washer

How do i remove the unloader valve on a karcher 4000 PRESSURE WASHER


... Karcher Pressure Washers

Poor pressure karcher g 2500 pressure washer with a 5.5 honda engine. No high pressure, hose pulsates as does water out of the outlet. have removed the unloader valve twice and cleaned it to no avail


I had this same problem on my pressure washer.the pump had some broken parts in it .i found my replacement pump on EBay. ... Karcher 2500 PSI Pressure Washer

G2500vh no high pressure and hose pulsates already removed and greased unloader valve


Here is a webpage full of videos of different instructors pertaining to repairing pressure washers. The valve you have removed and relubricated also sits into another valve which is hard to get out. Did you also remove the inner one and clean& lu ... Karcher 2500 PSI Pressure Washer

Have a Karcher 3000G pressure washer, low pressure. How do you remove the unloader valve?


Ask the professor. He knows everything about everything. I'm working on my degree now. Go to Youtube like he does. LOL ... Karcher 2500 PSI Pressure Washer

How to remove stuck unloader valve on craftsman pressure washer


... Craftsman Pressure Washers

The unloader valve seems to be hanging up!


The o-rings on the unloader may be worn out. Also you have to lube it with extremely good waterproof grease ... Karcher G3025OH Pressure Washer

The Water inlet valve # 8531325 let water run outside the dishwasher. After removing the valve I found a small ball of contamination inside and removed it. It now works with out spilling water. Do I still need a new valve?


IF the valve stops and starts water flow correctly, no you would not necessarily have to replace it. The valve should have an inlet screen to keep this from happening again.. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Karcher unloader valve


... Pressure Washers

How to install vrt3 unloader valve - Ar VRT3 - VRT3-250 Unloader Valve


... Ar VRT3 - VRT3-250 Unloader Valve

Clean and unloader valve on Karcher hd3500 pressure washer -intermittent pressure on and off. Cleaned inlet screen. Think unloader valve is is under pressure knob? Will cleaning help?


Hi:Cleaning it is not enough. You need to make sure the o-rings are in good shape and grease it with a very very good waterproof grease. ... Karcher Pressure Washers

Unloader valve will not come out


Unscrew brass fitting use crc then use 8mm socket turn back and forth should loosen as no threads hold it just rubber o ring.use silicone grease and refit.if using regularly lube and dont screw down manual adjuster ... Honda Karcher G2400HH-R Pressure Washer

By the time I recieved info, I'd already removed the intake valve, removed some debris from the screen, and was ready to test the movement of the solinoid valve. Right now,I can blow a little air thru either end while applying AC, and it stops tight w/o AC. If this is normal, I'll reasemble the unit. At least I was able to vacuum much insulation that a resident mouse had deposited on the floor years ago.


... Bosch 24 in. SMU70 Built-in Dishwasher

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

Unloader valve Thanks for the insight on my problem with a Karcher 550m. I have taken the pump motor out of the unit. How do I identify the unloader valve & replace it? There does not appear to be any other leaks. Is this the only part that needs replacing if pressure is down? Many thanks


... Pressure Washers

Purchased ge dishwasher model ghda674n00bg and discovered after installation that I removed the rubber check valve from the discharge line in error. Is it mandatory that this check valve be installed? Naturally I would prefer not to remove and reinstall unit. Thanks for your help Regards, John


... GE Dishwashers

Unloader valve where is unloader valve


It is almost always attached to the "manifold head" (mh) of the pump itself. These days, in many of the small home-owner units, the unloader is actually molded right into the mh. In other words, it becomes part of pump. But it will look different ... Pressure Washers

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

Sticking pressure washer unloader valve


... Karcher 2500 PSI Pressure Washer

My valve needle broke of while removing the float in the carburetor and now half of it is stuck in there how can i remove it?


Try using a air nozzle. If the needle is stuck up in there then a good blast of air should take care of it. ... Pressure Washers

HI there dish washer wont fill Ichecked fill valve its ok but there is no 110 volt reading to wires but when i remove purple wire from water valve and put ground wire to fill valve water comes in the dishwasher please tell what needs to be replaced thanks


There may be problem with your door switch/lock mechanism,be sure to check the main power supply to the dishwasher.\015\012if you have a electronic control board it might also have to be replaced. ... Dishwashers

Miele 646 sc plus inlet tank solonoid valve on water tank leaking. We moved the machine from one room to another and now this valve is squirting out water. We replaced both door seals thinking that was the problem, then started the machine with a side pannel removed, and saw the jet of water coming from the solonoid valve on the water inlet tank. Any ideas.


... Miele Dishwashers

I have a Sears (Briggs) 2550 washer mod # 580.752190, has been working great but when I got it out last week it wouldn't start with the water on, I turn the water off bleed the pressure out the wand and it started and ran great, I thought it might be the relief valve, I removed the valve turned on the water, a big stream was shooting out the hole where the valve goes, I started the engine and it ran but sounded like it was about half loaded. where do I go from here ? Thanks.


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0366 seconds