Having problems with your Karcher 2500 PSI Pressure Washer ?

No pressure when hose and nozzle are attached but when i disconne

\015 No pressure when hose and wand are attached but when I disconnect those i get pressure. I did change hose to a 3700psi from the 2500 one.\015

Answers :

Sounds like nozzel has dirt in it -try removing and cleaning it - failling this get a drill bit of same size of hole in nozzel and drill hole clean.......
worked for me with same problem..........
Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No pressure when hose and nozzle are attached but when i disconne

Sounds like nozzel has dirt in it -try removing and cleaning it - failling this get a drill bit of same size of hole in nozzel and drill hole clean.......worked for me with same problem..........P ... Karcher 2500 PSI Pressure Washer

How t o attach spray nozzle to craftsman pressure washer 1700 hose

... Craftsman 1700 PSI, 1.3 GPM Electric Pressure Washer w/ Steam Cleaner

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure

If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?

I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne

This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.

Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Karcher 2.56 keeps pulsing on and off whenever high pressure nozzle is attached. I have tried different nozzles and same thing is happening. when i press the lance without any attachment it works fine

Make sure you have bled all air from the system. Also make sure you have sufficient water supply; if house water pressure is too low or if your hose is too long or doesn't allow full flow, you may not be getting enough water to the unit. ... Karcher Pressure Washers

Pressure hose wont stay attached to karcher unit

... Karcher K3.540 Electric Pressure Washer

During installation of new dishwasher when I was attaching drain hose to pump I saw a small red rubber fap attached to end of pump discharge nozzle. Is this a backflow prevention or something to keep

It is a back flow preventer. Leave it alone and attach the drain hose. ... GE Profile PDW8400J Built-in Dishwasher

Briggs & Stratton 2200psi/model 020228 siphon hose shoots water out when using high pressure nozzles

... Briggs & Stratton 2200 PSI Gas Pressure Washer

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t

I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

I own a Karcher 3000 pressure washer. There is no water pressure. I've checked the obvious...hose to house, kinks, attachment is tight....Enging runs, no water pressure.

I had the same problem. On the top of the pump there is a little nickle colored button cap. It is attached on both sides with a screw. What this actually does I don't know but when I took it off with the motor running and put my finger over it th ... Karcher Pressure Washers

Pacific hydrstar pressure washer lost water pressure. Hose is fine when unattached. Replaced nozzles

... Pressure Washers

Karcher k4.600 T racer attachment will not work ; was great at first. I have removed and washed the pressure nozzles and refitted them, but it still has no pressure. Any ideas ?

... Karcher Pressure Washers

Our washer had been woring fine earlier this afternoon. After a short (about 10 minute) break, it developed only hose pressure. We disassembled the nozzle, figuring there might be some obstruction; also made sure the hose wasn't kinked. No luck even though the motor is apparently running fine. It's about one year old. What do I do now?

Can you see my posting: "Karcher - no pressure", also my own comment where I describe my later technical findings - mashed up gearbox. Could it be the same problem as yours, where the motor sounds to be running just fine but there is simply no press ... Karcher PSI Electric Pressure Washer

PCP2100F What do I need to connect my hose to the pressure washer unit? My standard hose attachments are too small...

... Pressure Washers

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a

If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

Hose connections I have a McCulloch FHH18A pressure washer. Does anyone have a diagram showing where the ends of the hoses for the two tanks should be attached at the tank selector? I took it apart and neglected to make a diagram for reference.

... McCulloch FHH18A Electric Pressure Washer

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?

If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

I am trying to use the soap...i know i have to use the low pressure nozzle but which nozzle do i attach it to under the machine

... Pressure Washers

When you trigger the nozzle there is no increase in the pressure, just the water pressure from the hose

... Pressure Washers

I have a Clean Shot 2050 PSI washer. I can get it to start, but I have very little prerssure. A household shower has more pressure. The garden hose nozzle has more pressure. Any thoughts????


I have a craftsman 2600 psi powered by a honda engine. i have hooked up the water hose and the pressure hose. Turned on the water and went to bleed the air out of the nozzle and nothing comes out.

... Craftsman 2600 PSI Honda Powered Pressure Washer

Low Pressure The output pressure seems very low. No crimps in the hose, the engine runs fine, the nozzle seems "open". Any suggestions?

... Honda Black Max 2600 PSI Pressure Washer

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.

If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0859 seconds