Having problems with your Karcher 2500 PSI Pressure Washer ?

Excell vr2522 - picked up 2nd hand, cant figure out how to get unit to spray chemical? is there a chemical bit for this model? it appears to all be one peice


Answers :

Use black tip or lowest pressure tip
Use the black tip or lowest pressure one that should solve your problem
Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Excell vr2522 - picked up 2nd hand, cant figure out how to get unit to spray chemical? is there a chemical bit for this model? it appears to all be one peice


Use black tip or lowest pressure tip ... Karcher 2500 PSI Pressure Washer

The top spray arm of my Frigidare model FBD4315LFC0 Aqua Surge dishwasher fell off. Their appears to be a missing part. I've been searching online for a schematic and can't find one thorough enough to use. The parts I have are: 1. The top sprayer arm (the one in the top of the tub) 2. The two piece plastic keeper ring that appears to fit into the top of the spray arm. 3. A small white grommet looking item that fit inside the keeper nut. 4. The keeper nut that screws directly onto the wate


Hello there:hey sorry i keep getting disconnected i will be back on really soon i need to find out what is going on i hope these things that i have discussed with you is helping you out the parts are not as hard as they look once yo ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

Missing "turnscrew" I just purchased this as a floor model from Olum's in Vestal, NY. I brought the unit home and the "turnscrew" that fastens down the lower spray arm is missing. Please email me the part # so that I can have them secure one for me and I can start using my dishwasher! Thanks. Joe Roma


... Whirlpool DP940PWSQ Free-Standing Dishwasher

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

I just got a dishwasher yesterday that was a floor model. I saw there was tape on the front and started spraying it with windex, then used nail polish remover (which ran down and stained a little), then I used this sponge which was a little rough on one side and I think I discolored and scratched front a little bit. How do I fix this?


Pick up an Appliance Repair Kit in the color you have selected (I'm assuming white, so get Appliance White) and follow the instructions. It'll have some epoxy and a finishing paint to help mask the mar. ... Frigidaire Dishwashers

My dishwasher is leaking from underneath, front left as you look at it. If i go underneath it, there appears to be a seal on the outside (it does not appear to be the one that runs along the bottom of the inside of the dishwasher) that has come away at one point. Do you know a) how to get the front panel off (the bit that makes it look built in),b) how can i get another one of these seals. I assume if i get one we can just fit it into place. Many thanks, Robyn J


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012p80897 ... Neff 24 in. S5453X1 Built-in Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

During wash cycle water leak appears on the floor at the left side of the unit. this is a new unit model #Kuds301vwh #FO1114221 purchased and then installed on 3/25/10. Gasket was replaced on door by factory repair man and leak continues. unit appears to be level.Unit is covered under warrantee.


... KitchenAid KUDS30IV Builtin Dishwasher

16 year old GE built-in dishwasher, model GSD900. Springs that prevent front door from falling disconnected. ALL parts APPEAR to be in good condition. I say appear in good condition because I don't know what they are supposed to look like. But I see nothing obviously broken. The 2 springs appear intact. The connecting cable is good. However one of the 2 springs is shorter than the other. It may be shorter because one is supposed to stretch to the other side of the dw? So number 1


... GE Dishwashers

Unit won't pump out, checked the lower impeller and it was very loose, is there a drain valve on this unit? Model 587.14249991 The upper impeller is a fixed unit right to the motor but it appears the lower impeller is a push fit over a rubber sleeve. I only saewa check valve in the drain hose, is there any thing else I should check? hose is clear and the switch for the float is working ok.


At the bottom of the unit where the hose goes is a check valve. check to see if clogged. ... Dishwashers

It appears that water is not running through the dishwasher or that the sprayers are not working correctly. There doesn't appear to be a clog. However, I did find a round rubber "washer" (I think that is what they are called) laying in the bottom of the dishwasher - where does this part go. It was working fine until this wash. The heating element works fine but like I said it appears that something may be wrong with the spray tower. Please advise Model number of Hotpoint: HDA3420Z01BB T


Hi,\012When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Hotpoint Dishwashers

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

Bosch dishwasher, Model SMU 7056, UC 09, FD 7309. My older unit has operated flawlessly for years. Two days ago it started to "stall" in one cycle and not progress to the next, e.g., stayed in the wash cycle and would not move on to rinse. In addition the heat generated in the machine was way below normal. A repairman told me that if the water doesn't get hot enough, the unit will not move on to the next cycle. I always use the "Regular Wash" option, but tried other options such as 'Economy


... Bosch Dishwashers

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch Dishwashers

Maytag model MDBTT59AWB does not spray water. Water fills and drains properly and the motor appears to be working as well. Just no water spraying at all. Any ideas? Haven't found any answers anywhere.Thanks,Don


... Maytag Dishwashers

ON REGULAR WASH CYCLE , WATER DOES NOT DRAIN FROM TUB AT END OF CYCLE. A FRIEND SAID I NEEDED NEW TIMER, BUT WEB SEARCH SAYS THERE ARE 2 DIFFERENT TIMERS LISTED FOR THIS MODEL AT ONE PRICE AND THEN DOUBLE THE PRICE FOR OTHER. DO I NEED TIMER, WHICH ONE. UNIT IS 13 YEARS OLD, WORTH REPAIRING ???


Hi,Typically when a dishwasher does not drain it is not due to the timer. The most common reason for it not to drain is a clog in the hose between the pump on the dishwasher and the outlet it drains into, like the pipe under the sink or g ... Magic Chef 24 in. DU4500 Built-in Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch 24 in. SMU40 Built-in Dishwasher

Poor drying, mold building up in the tub. The condensing drying system is not working well. I pulled the unit out and removed a panel on the left side (facing washer). Saw that the plastic box that appears to be set up for moist air removal and vents to the tub had considerable mold in it at the top of one of the passage ways. Looked like it might be blocking air flow. Could this be a cause of poor drying? Can this unit be removed and cleaned? Also soap isn't dissolving. Bad board controllin


Hi.Poor drying is often caused by a faulty moisture sensor. If there is mold covering the sensor housing , that can be cause for the problem. Regarding the door detergent drawer problem, that is often caused by a defective doo ... LG LDF6810ST Stainless Steel Built-in Dishwasher

One of my drawers is not draining completely all of a sudden... Recently, the unit started making a grinding sound during one of its cycles. Now, it doesn't drain completely. I took out the filter plate with motor assembly and found that the underside was a bit chewed up. Not sure if this could cause the draining problem. Any thoughts?


That sounds like it could very will be the problem, also check to make sure drain hose is not clogged by blowing down it. should be able to blow free and clear. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Maytag dishwasher model mdb7809awm1 does not start. you can select cycle, option button appears but you cannot change the one that appears as selected, and when you press start, nothing happens


... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0917 seconds