Having problems with your Karcher 2500 PSI Pressure Washer ?

Gas is leaking into the oil tank on a craftsman pressure washer. it will do this while it is running or sitting in storeage. it has a briggs and stratton intek engine.


Answers :

Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Gas is leaking into the oil tank on a craftsman pressure washer. it will do this while it is running or sitting in storeage. it has a briggs and stratton intek engine.


... Karcher 2500 PSI Pressure Washer

Briggs and stratton 900 intek series 205cc starts up then it stops running


... Briggs & Stratton Pressure Washers

Looking to change engine oil - Briggs & Stratton Murray 020456 2400 PSI 20 GPM 190cc Briggs Stratton Gas Powered Pressur


... Briggs & Stratton Murray 020456 2400 PSI 20 GPM 190cc Briggs Stratton Gas Powered Pressur

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Briggs and stratton 10hp intek pressure washer wont run


... Briggs & Stratton Gas Pressure Washer 20244

Cannot figure out how to remove the oil plug to drain the oil. Label points to a spot that looks like it might be a plug, but can't figure out how to remove it. It is a 2500 psi Mdl VR2500 Briggs & Stratton engine Honda Power Washer. Ken from NH


Should take a 3/8" socket extention ... Pressure Washers

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Briggs & Stratton engine loses power


Hello herb1007If it is running it would burn any oil off the top of the piston. (that got there when you tipped it). It sounds like you carburetor needs cleaning. There are sprays on the market that sometime help with this. ... Briggs & Stratton Pressure Washers

What causes gray oil in briggs and stratton engine?


... Pressure Washers

Briggs and stratton 900 intek series 205cc starts up then it stops running


... Briggs & Stratton Pressure Washers

Engine Stops after 10min run time - Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer


Check the breather hole on the gas cap.\015\012run the engine with the cap off and see if it still stalls. ... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

When I start my pressure washer on full choke it works fine when I place choke in wide open position gas runs out of the carburetor.what could be wrong.the engine issas by Briggs and Stratton.


You need to take the float bowl off the carb from the bottom . You haven't given a lot of information about who did what to the carburator but somebody must have screwed with the float pisition for this to be happening . The way all carburtors work i ... Simpson WS4050V Water Shotgun 4000 Psi Cold Water Electric Start Gas Powered Pressure Washer W/ Vanguard Engine

Engine runs fine but will not spray - Briggs & Stratton 2200 PSI Gas Pressure Washer


Check all of your inlet hoses, one may have a kink or a blocked up filter screen. If nothing is clogged your pump has broken and will need replaced. ... Briggs & Stratton 2200 PSI Gas Pressure Washer

I have a 2550 psi pressure washer with a 6.75 hp briggs and stratton engine with ready start. i wont start. has gas and oil plug looks good. any solutions?


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

How to drain oil from engine - Craftsman 3000 PSI 27 GPM Briggs Stratton Powered Pressure Washer


Square socket on the bottom of the engine. I think a 3/8 extension on a ratchet is correct. ... Craftsman 3000 PSI 27 GPM Briggs Stratton Powered Pressure Washer

Gas leaking from carb on Briggs and Stratton engine


`v already answerd this,are you slow? with oil in the sump you can do no damage by running the engine with abit of smoke,it will clear up very quickly. i find it hard to believe youhave done the things you claim if you dont know what a carby bowl is! ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

My pressure washer was running fine then bogged out.The person who lent it to me said dont worry about the oil it is fine, so i didnt check. I checked the oil and it was almost bone dry. So i filled it with oil but now it wont start, is it possible that the engine is siezed up or, can i get it running.


You probably helped destroy the engine. Honda's are great engines until they run low on oil ... Karcher 2500 PSI Pressure Washer

My briggs and stratton lawnmower will start but not stay running


... Brute 7800821 22-Inch 190cc Briggs And Stratton 625 Series Gas Powered FWD Self Propelled Lawn Mower

Oil leak but dipstick says its full i have a briggs &stratton 2200psi q45 seris 2.0 gpm


... Briggs & Stratton Pressure Washers

Briggs n stratton 3.75 hp speed clean pressure washer oil capacity


... Briggs & Stratton 2200 PSI Gas Pressure Washer

Briggs and stratton engine hunting - Briggs & Stratton Pressure Washer Projectpro Spray Nozzle


What is the question??? ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I temporarily misplaced (not lost for good) the owners manual for my honda pressure washer : engine and pump. I do not want to run my machine again until I verify the pump oil content/level. On the pump itself, at the top, there is a black, unscrewable oil cap, with blue-ish oil in it, BUT NO DIP STICK! How do I check the level? What kind of oil, specs etc? Thanks!


Http://www.ultimatewasher.com/download/honda-engines/gc160.pdf ... Karcher 2500 PSI Pressure Washer

I have a Honda Excel Pressure washer with 5 hp engine. I just started using it for 5 - 10 minutes and the engine stopped running. I can't pull the cord to turn over the engine. Ithas plenty of oil, I disconnected the hose and the wand and still can't get the engine to turn over.What next?????


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0745 seconds