Having problems with your Karcher 2500 PSI Pressure Washer ?

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Answers :

Hi, Karcher calls the unloader valve a spill valve,
this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps
http://www.pressureparts.com/ManualViewPage.aspx?Manual=/mmDEV/PDF/karcherparts/g2500vh.pdf

the part number is on page 9 of the drawing
spill valve 45910400
hope this helps , we usually use some good quality silicone grease to lube the valve ,

Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.


... Karcher Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not much. This happened after i ran water out of trigger gun with no lance attached, machine switched on. Seems to leak from trigger handle aswell. Many thanks in advance


This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump. ... Pressure Washers

Trigger gun does not function each time the trigger is pulled. The water supply is more than adequate, water inlet screen is clean, water pressure adequate, no kinks in hose, all attachments are clear and I am lost. Thanks


I have same problem. This is a fault of the bypass valve at the pump end. It has to be taken apart and serviced. ... Karcher G3025OH Pressure Washer

I have a Kracher K 4000 GS pressure washer and it seems to have been fine until today. When I start it and squeeze the trigger there is nor pressure, water comes out but as it would normally from the hose. The engine does not even seem to be under load. I used it the other day and got pressure when I picnhed off the soap hose but that did not work this time.


... Karcher G3025OH Pressure Washer

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?


If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

Nilfisk Alto Active Waterblaster.Starts up good. When I release trigger on gun it does not start pressure again. I have to take water hose off


... Pressure Washers

When you trigger the nozzle there is no increase in the pressure, just the water pressure from the hose


... Pressure Washers

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers

I have a generac 2200 psi pressure washer. It starts and runs fine as long as I have the trigger pulled to spray water. When i let off the trigger it kills the engine. What could this be and how can I fix it? Model number is 01040-2


... Briggs & Stratton Briggs Stratton Pro Style Pressure Washer Gun Generac

I have a DPH3800 Dewalt pressure washer and the soaper isn't working properly. Right tip is being used but when trigger is not pressed it puts water into the bucket. When trigger is pressed it does **** some solution into the hose but very little and very slow. The valve is opened all the way. I know my former partner used bleach in the system which I read in the manual is a no no but it did work at the end of last season. Any ideas?


How is the pump connected on a john deere 3800 psi. i took out the 4 bolts and drained the oil. pump is stuck to cam. how does it come off? ... Dewalt 3800 PSI Pressure Washer

I need to winterize the built-in Kenmore dishwasher in a mountain cabin where winter temperatures will drop below freezing. The unit is at least 10-15 years old, but I don't have the model number handy. My approach to the cabin water pipes in general will be to gravity-drain them and then blow out remaining water by adding and releasing air pressure. RV antifreeze will go into all P-traps. When it comes to the dishwasher, my plan is to remove the drain hose from the P-trap and drain it as mu


In order to get the water out the best thing to use is a wet dry shop vac and attch it to the end of the drain hose on either your dishwasher or clothes washer this will remove any water in the drain pumps.As far as RV anti freeze being added not sur ... Kenmore Dishwashers

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

I have a Karcher Electric K3.68 MR Reconditioned pressure washer that I've had for about two years and used about three times. The model number on the tag is: 9.559-635.0 and the Serial number is 000863. The washer pulses when I'm not sqeezing the trigger, It no longer will dispense cleaner when I turn the washer head to that position and now there is water flowing out of the bottom of the unit.


... Karcher Pressure Washers

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Karcher 3.86M Electric pressure washer. Plugged it into outlet. Unit started running. turned it to off position. Attached hose. Turned on water valve. Turned on switch. Squeezed trigger. Nothing happened. Will not run. Ciruit breaker was reset.


... Karcher PSI Electric Pressure Washer

Karcher k3.86 lowered operating pressure and constant surging at idle, it back feeds into the water feed/supply hose until trigger is pressed


It sounds like your non-return valves are damaged. in the pump there are usualy 3 non-return valves, these are located under 3 large brass hexagonal caps. take the valve out and inspect them. if you are lucky they may just need cleaning, as sometimes ... Karcher K2.26 Electric Power Washer

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Shark pressure washer with honda 5.0hp motor when in use spraying with good pressure it the pressure shuts off and motor sounds like its about to shove a rod through the cases shut it off restart it andd the same thing occurs all fluid levels good pump and motor. water pressure from hose bib good. may b low water pres. for short time due to possible kink in hose reel not sure


What type pump oil to usefor karcher 2400 psi ... Honda Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0950 seconds