Having problems with your Karcher 2500 PSI Pressure Washer ?

Lost pressure. Inlet water pressure fine. I fixed this a few tears ago and I cannot remember what I did.


Answers :

First check the triger velve is working ok,, if its stuck strip it out and free it off
Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lost pressure. Inlet water pressure fine. I fixed this a few tears ago and I cannot remember what I did.


First check the triger velve is working ok,, if its stuck strip it out and free it off ... Karcher 2500 PSI Pressure Washer

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

Took these from a previous page, because this is what is happening to our lab Miele Platinum G892/G892 SC. Can you tell me what the problem is and how to fix it? Thanks. intake /drain light is flashing,full water- Guest Feb 26, 2009- I have same problem - open the door and there is water at the bottom of the dishwasher - when I restart program, the water drains out fine. Also, I have great water pressure coming into the dishwasher, filters are clean, etc. I am suspecting it is a circula


If there is verified power at the pump motor - your timer is defective.Thanks For using Fixya!! ... Dishwashers

I have a EuroTech dishwasher Model# EDW254E/SB. It was working fine but now it gives the Err code:er1 Its not letting incoming water in i know that. As well I have been told to try reducing the water pressure at the facet. Did that nothing.It drains but wont cycle to the next stage and let water in. I am presuming there is a valve of some sort not opening? And does the dishwasher have to be completly romoved to fix. Thanks


Hi and welcome to FixYa. I am Kelly. \015\012\015\012This is a water level sensing problem. Look inside your lower wash tub area and see if you either see a circular device off to one side or a finger like device sticking up about 2 inc ... Dishwashers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started.


Ok I wasnt satisfied w/ the previous answer so I did some digging. I took off all the hose attachments and drained the line. I then checked for any clogging in ALL the screens. As usual the wand screen was clogged. this is an easy fix w/ a safety pin ... Pressure Washers

Error Code E1 means longer inlet time. possible causes faucet is not opened, or water intake is restricted, or water pressure is too low, according to the BRADA portable dishwasher model EP9242AWW What does that mean and how do I fix it? I have shut the water faucet off and the error message still shows.


... Dishwashers

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

I have a Husky 2600 Psi 2.3 GPM Honda powered gas pressure washer. When i turn it on the motor runs fine, But when i squeeze the trigger the water is not pressurized when it comes out. How do i fix this problem?


... Honda Pressure Washers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

Dishwasher works fine except that after the drying cycle, water slowly builds up in the bottom of the dishwasher. It did this a few years ago for several months, but then it stopped doing it altogether. I did nothing to fix it. Now it's started doing it again. I run the dial around to a point where it drains, let the water drain and then turn it back to off before the drying cycle begins.


Hello,\015\012\015\012This would mean that the dishwashers water valve has failed. This is a simple repair to make yourself. The lower access panel would need to be removed, four screws. You can purchase the part from the link below.\015\012 ... GE Dishwashers

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My Frigidaire dishwasher will not start. It was working fine about a month ago. The lights on the panel are working and I had the water line checked and it is o.k. I cannot find a serial number but the book that came with it is for the 500, 1100, 1400 & 1500 series with fully electronic control.


My Frigidaire 500, 1100, 1400, 1500 & 2400 Series Dishwasher was purchased a month ago and it will not start either. The 8 second lock under "Heat Dry" is lit, but nothing happens when you press any of the other buttons. Any ideas? ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Cannot draw soap or cleaning solution from a bucket. Is their a adjustment screw to make it draw. Pressure washer works fine with just water. Lost the operators manual.


You first must slide the nozzle forward to the low pressure setting for it to inject any detergent. It will only draw the detergent in low pressure mode. If it still will not draw up the detergent, then the injector may be clogged. It must be through ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Gld4260l00ss has power. there is light indicators on front panel, but when press start button, nothing. new inlet water valve solenoid installed last month and unit has ran fine until two days ago. I have unplugged power and plugged back in but no help.


I would remove the control panel and ck the ribon form the touch pad to the control .it is very common for these connections to fail remove the ribon and re insert it and try again . also ck the touch pad and make ... GE GLD4260LSS Dishwasher

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Model #gld5800l15cc doesn't clean dishes. doesn't seem to fill enuff before the cycle. the pump starves. for the heck of it I poured water into it manually and it worked fine. all the sparayers then had good pressure. I cleaned the inlet screen at the solenoid and its still the same. Help please!!!!!


Replace the level sensor in the tub of the washer. ... GE Dishwashers

No pressure Engine runs fine, fairly new machine from Home Depot, used only 2 or 3 times, kept indoors in a heated garage, checked inlet water and it's ok, no kinks in line...help!!!


... Pressure Washers

Cannot start my Comet pressure washer...water runs thru fine. Had set choke to open (push to left) and start to left.


Hi: Some things to check: Is the gas old or contaminated with water. Change it if you are unsure. Are you getting a spark? To check this: BE CAREFUL. Remove the plug. Plug it back into its wire. Hold it WITH INSULATED PLIERS so the tip is close ... Comet Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1976 seconds