Having problems with your Karcher 2500 PSI Pressure Washer ?

Needle valve honda gcv160

\015 Carb needle valve adjustment honda gcv 160\015

Answers :

Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Needle valve honda gcv160


... Karcher 2500 PSI Pressure Washer

Wheres the pressure relief valve on my Honda GCV160


... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Hard to start my pressure washer with GCV160 Honda engine


... Karcher 2500 PSI Pressure Washer

Honda gc160 steps to change a broken valve


... Pressure Washers

Honda GVC 160 lost pressure - noticed small black valve (back - rear) after pressure builds up , short spray then nothing - hot water comes shooting out the black valve - did something pop off?


The small black valve is called a thermal relief valve. If it is open you will have no pressure. If the water is getting hot enough to pop that valve, there might be internal problems with the pump. ... Karcher 2500 PSI Pressure Washer

I have an MTD Honda powered mower 187 cc. vert shaft made in Canada, I freed the carboned exhaust valve and went to reassemble but didn't pay attention to the valve timing. Anyone know where to put the cam compared to the piston? Any timing marks any where,I can't see any. Thanks


... Pressure Washers

Honda gcv160 wont dispence detergent - Craftsman 2600 PSI Honda Powered Pressure Washer


It will not draw soap while using pressure take out the nozzle or use the large black nozzle ... Craftsman 2600 PSI Honda Powered Pressure Washer

Honda gx340 hi i have a honda gx340 the valves have bend on me twice how is this happening and can i stop it from bending them


Have the engine timing set correctly so that the valve do not contact the piston. ... Honda Pressure Washer PSI 3000

Honda Hydroquick Model# B435M will not take in soap solution from valve, I allready checked valve for restictions and found none. Whats the problem?


... Honda Pressure Washer PSI 3000

I have an MTD Honda powered mower 187 cc. vert shaft made in Canada, I freed the carboned exhaust valve and went to reassemble but didn't pay attention to the valve timing. Anyone know where to pu


... Pressure Washers

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

Honda gcv160 wont dipenve detergent - Craftsman 2600 PSI Honda Powered Pressure Washer


... Craftsman 2600 PSI Honda Powered Pressure Washer

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

My friend gave a pressure washer honda 5.5. He tried to adjust the valves now it won,t start. What is the valve clearance


The valve clearance is 0.15mm Intake 0.20 Exhaust ... Honda Pressure Washers

My Honda pressure washer is leaking out of the thermal relief valve and I am looking for a part,I also do not have the manual. The model number is WGC 3030 and it is 3.0 gpm 9.0HP. The number on the thermal valve is 33120004,where can I find a part?


Does the thermal valve just screw into the pump head, if so what size thread is it? I have 1/4, 3/8, 1/2 in stock. ... Honda Pressure Washer PSI 3000

Diagram on carb for briggs stratton 17.5 , needle valve and seat wont go together


... Briggs & Stratton Lawnmower Lawn Mower Pressure Washer Carburetor Carb

My valve needle broke of while removing the float in the carburetor and now half of it is stuck in there how can i remove it?


Try using a air nozzle. If the needle is stuck up in there then a good blast of air should take care of it. ... Pressure Washers

Honda GCV160 pressure washers turn off when turn on the gum


... Karcher 2500 PSI Pressure Washer

Honda GCV160 Engine Won't Start


HelloYou should siphon out all the old gas you can. Replace with new gas. Check that the spark plug is good and the air filter is clean. Spray some carb cleaner in the carburetor.. Also, you should check the oil level and change the oil i ... Karcher 2500 PSI Pressure Washer

Honda gcv160 pull handle stuck in


... Honda Pressure Washers

How to set valve lash on honda gx 390 13hp engine


... Honda Horizontal OHV Engine with Electric Start - 390cc, GX Series,

Black max pressure washer 2600 psi 2.3 gph honda unloader valve stuck


... Honda Black Max 2600 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0265 seconds