Having problems with your Karcher 2500 PSI Pressure Washer ?

Gas run out of carberator when running - Karcher 2500 PSI Pressure Washer


Answers :

Hi james
\015\012Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible.
Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Also be sure to check and clean your spark arrestor in the exaust,if you have one installed on your engine.
\015\012Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
\015\012Note:Before you disassemble the carburetor:
Write down on a piece of paper or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.
Mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.
That way you will know which way it goes back together when you reassemble it.
\015\012Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.
Check you fuel line condition after a while they will degrade and need replacment.
\015\012Check/Clean/Replace your fuel filter if you have one, normally they are located in the fuel tank of chainsaws and weedeaters.
When you remove your fuel lines from the carburetor be sure to make a drawing to how the lines are connected to the carburetor or take a pictue for later reference.
Normally the big line will be the line the fuel filter is connected to inside of the tank.The smaller of the two lines is the return to the fuel tank from the carburetor after it is pumped thru the carburetor by the primer bulb.
Make sure you are using fresh fuel...and oil if your using a two cycle chainsaw or weedeater with the oil to the right mixture...too much oil as it can cause hard starting and excessive smoking.
If the chainsaw/trimmer is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
\015\012When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.
Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.
Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.
Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.
Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.
When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.
Note:
The little spring inside of the carburetor goes under the float arm.
That is where your fuel inlet needle/float valve is located...on the arm at the end.
Normally there is a small indention in the carburetor base and a small protrusion on the underneath of the float arm where the spring will be in the right postion for installation.
The spring will set in the indention and you will install the float arm with the needle/float valve and float rod into position over top of the spring,you will push down until it is in position and then you can tighten the screw that holds the float arm assembly in position.
Once you have your carburetor cleaned/rebuilt that should solve your problem.
Please take time to rate me
Bud
It sounds like you have dirty petrol in the carburateur bowl preventing the float valve to shut the petrol supply. Clean the carburateur bowl and the float valve seat, discard the petrol in the petrol tank and flush the tank clean
Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Gas run out of carberator when running - Karcher 2500 PSI Pressure Washer


Hi james\015\012Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.Also be ... Karcher 2500 PSI Pressure Washer

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Karcher 2600 psi pressure washer wont stay running


Remove and clean the carburator. Sound line a stuck needle on the float.  ... Karcher 2500 PSI Pressure Washer

I have a karcher pressure washer 1800 psi i bought from walmart it was running good until i had a power surge with the plug in. what can i do can i change the fuse in the plug or do i have to open the pressure washer up and replace a fuse.... thanks


You will have to take the cover off & look for melted wires or a fuse.\015\012if there is no fuse the capacitor may have been cooked.\015\012it should be a white cylinder.if it has been damaged it will have burn marks and may be swollen. ... Karcher PSI Electric Pressure Washer

I cannot get my Karcher 2600 psi gas powered pressure washer to start. Got gas oil no pressure build up in hose.


... Karcher 2500 PSI Pressure Washer

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Can i run plus gas in my washer - Northstar Pressure Washer 3000 PSI


I'm not sure what you mean.I think you are asking if your power washer needs oil mixed with the gas.Does your machine have a oil reservoir below the engine?If there is a place to put engine oil, then your engine runs on ordinary gas ... Northstar Pressure Washer 3000 PSI

Karcher 620m runs but will not pump water - Karcher 2500 PSI Pressure Washer


The pump that connects to the motor could be bad/and or loose ... Karcher 2500 PSI Pressure Washer

I have an 1800 psi coleman gas washer that worked fine,then the next time i went to use it no pressure.motor runs fine,good water pressure just will not build pressure thanks dave


... Coleman Pressure Washer PW0881800

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

I have a Husky 2600 Psi 2.3 GPM Honda powered gas pressure washer. When i turn it on the motor runs fine, But when i squeeze the trigger the water is not pressurized when it comes out. How do i fix this problem?


... Honda Pressure Washers

My Karcher gas powered 3100 psi pressure washer has a constant water flow pulsing


... Pressure Washers

Engine runs fine but will not spray - Briggs & Stratton 2200 PSI Gas Pressure Washer


Check all of your inlet hoses, one may have a kink or a blocked up filter screen. If nothing is clogged your pump has broken and will need replaced. ... Briggs & Stratton 2200 PSI Gas Pressure Washer

Engine runs,no water when trigger pressed. - Karcher G2650HHR Gas Pressure Washer


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuck ... Karcher G2650HHR Gas Pressure Washer

Karcher 1800 PSI washer with 3.75 HP engine doesn't run smoothly-hunts. Thought it might be water in the gas but it isn't that. Seems to be a governor problem...has to be something simple, I would think.


... Pressure Washers

It start then stops running - Honda 2500 PSI Gas Pressure Washer


Have you checked to see if it has a good strong spark? Remove plug, put back on coil wire, put end of spark plug next to the engine head bolts. Then turn the motor over a few times and watch the spark plug to see if a good strong jumps across from pl ... Honda 2500 PSI Gas Pressure Washer

Engine will not turn-over. It is a Honda 11 HP, OHV on a Karcher Pressure Washer. It was running fine for about 45 minutes. All of a sudden it stopped. When I tried to start it again, the engine is bound up so that the pull rope will not pull out at all. It has plenty of gas. The crank case is full of oil, not over full.


Pull the spart plug out and see if you can pull it. Sometimes the carb will flood the engine to a point that they get hydrolic lock.If it does free up then I suggest cleaning the carburator before trying to start it again.If it does not free up the y ... Karcher 2500 PSI Pressure Washer

I have a karcher 14000G 3500 psi pressure washer that won't stay running


... Pressure Washers

Sears pressure washer mod#580-751781 7.8 hp /2500 psi / 3gpm Starts fine and runs for 15 seconds then shuts off. Changed out gas and oil still no improvement.


... Craftsman 2500 PSI Briggs Stratton Powered Pressure Washer

I need 0 rings for Karcher 4000 psi pressure washer. Where can I find them?


... Karcher 4000 PSI 36 GPM Gas Pressure Washer G 4000 OH

I have a Troybilt 2000 PSI gas pressure washer. The engine runs great until I squeeze the wand trigger. At this point the engine immediately shuts off. Any ideas as to why?


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

WHAT WILL HAPPEN TO A CRAFTSMAN GAS POWERED 2500 PSI PRESSURE WASHER IF SOMEONE RUNS DIESEL THROUGH IT AS A DETERGENT OR DE-GREASER? WILL THIS RUIN THE SEALS IN THE PUMP? OR CAN THIS PROBLEM BE REVERSED WITH A FULL TAKE APART AND CLEAN UP OF ALL PARTS?


If you want to run a very small amount through the engine to help clean carbon deposits I would say that was fine as long as you only used 1-2 ounces to the gallon. But if you want to run diesel through the pump itself I would not recommend this. ... Pressure Washers

How to change oil Karcher (Robin engine) 2600 PSI Gas pressure washer


... Karcher G 2600 VH Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1464 seconds