Having problems with your Karcher 2500 PSI Pressure Washer ?

No pressure when switched on

\015 My machine lost all pressure turned it off for a while then turned back on but there was no pressure also it will stay on for a few minutes then stop\015

Answers :

Repair Help & Product Troubleshooting for Karcher 2500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C

... Dishwashers

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'

Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???

If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Indesit d41 dishwasher overfilling, pressure switch seems ok(checked with multimeter) ,when pressure switch is manually operated the electro fill valve remains open. only time fill vave shuts is when power is off or door is open. can someone please help as i cant find wiring diagram or service guide online

Possible faulty pressure switch or a faulty drain pump ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

How to calibrate dwyer pressure switch 1900 - Dwyer 1910-10 Pressure Switch Series 1900

... Dwyer 1910-10 Pressure Switch Series 1900

Hi I have a HOBART AMX-70 and my question is does the pressure switches b3 and b4 work with water or air pressure because when i remove pipes from switches i get nothing.

Www.ukexplorers.co.uk/shop/pdf/AMX.pdfThat is link for the entire manual!B4 I do know is water pressure, ... Dishwashers

Kelvinator KD12WW dish washer How do I open the unit to change the pressure switch as the unit will only take in a cup full of water. I have purchased the pressure switch for Tecsa Cape town Regards Chris

... Kelvinator Dishwashers

What does a failed pressure switch look like? I have removed my pressure switch (part 8071024). It is clean without apparent damage. The point at which the small, black hose connects has a plastic "button" inside, which appears as if it should move but it does not move at all. Is it seized? I think my issue is very similar to issue "Dishwasher Flooding Out" article on your site from (Oct 2007). This is a very helpful site, and thank you for any input on this question.

... Asko 1385 Dishwasher

Pressure washer does not discharge water under pressure until the nozzle has been removed from the lance- press switch and release, refit nozzle and then the water is discharged. Will switch off but does not activate next time.

... Pressure Washers

My kew alto force pressure washer would normally cut out and start again in about 30 minutes. now it will not start at all. i have dismantled the pump from the housing and everything looks ok even the pressure switch is very clean. Could it be the on-off switch that is faulty. any help would be appreciated. fg

... Pressure Washers

Pressure switch Tipe 40 Max16(4) 250v 2317A Pressure Switch

Try http://www.manualowl.comHope this helps. ... Dishwashers


... Indesit 24 in. D63 Free-standing Dishwasher

Jammed pressure switch on craftsmen electric pressure washer

... Pressure Washers

I have a Pressure problem on my PowerCraft pressure washer. On initial switch-on the machine runs at low pressure. If I then rotate the end of the lance to detergent application mode and then rotate it back to high pressure mode the high pressure kicks in and all is well. Is the lance faulty?

... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!

You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Kew hobby 1650 pressure washer pressure switch replacement

... Pressure Washers

My karcher pressure washer is switching on and off when the wand is not being used. the pressure should hold but it appears to cut in and out every 2 secs. the machine works o.k. when pulling the wand trigger but i think the pressure is slightly reduced.

Unfortunately these little units have this problem commonly, 9 times out of 10 it will be the plastic head on the unit will be cracked and leaking slightly... it builds up pressure then leaks out and tries to build up the pressure again ... Karcher K2.26 Electric Power Washer

Karcher pressure washer lack of pressure and intermittent noise, when not using the lance, as if pump switches off. When using the machine (K3.99M) it works but lacks pressure.

This sounds like an internal crack in the outlet head, simple to replace and not that dear ... Karcher K2.26 Electric Power Washer

I have a karcher 4.6 pressure washer that developed the usual fault.... drop in pressure and leaking from the cylinder head. I have replaced the cylinder head and the attached control chamber. The pressure is now good again and the leak is fixed. Unfortunately now when the trigger on the lance is released the the machine does not switch off automatically. I have bled the machine by letting water run through it

... Karcher Pressure Washers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app

... Karcher 1550PSI Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.

Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

Karcher K6.50 possible pressure switch problem?

Mark, Did you find out where the V spring go? i have the same problem. ... Pressure Washers

Have a Ryobi rpw 2400 petrol new never used yet, can't start it. If switch on O,nothing happen. If on 'I' pressure build up and block the motor .Any idea for solution?

... Honda Karcher G2400HH-R Pressure Washer

Troy bilt pressure washer will not start. I checked continuity between the black wire from the coil and ground and it is showing a dead short which means one of my "fail safe" switches is probably clo

... Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer CARB 020487

Need jackson jpx-200 pressure switches

... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0767 seconds