Having problems with your Karcher 3000 Psigaspressure Washer ?

I HAVE ONLY USED THREE TIMES IN THREE YEARS. WILL NOT START. HAD CHECKED AND IS NOT GETTING FUEL. ARE THEY BAD ABOUT CARB PROBLEMS. MODEL G2600 P/N 1194-4050 THANKS SELBY


Answers :

You will have to strip the carb and replace the gaskets and diaphragms. Gas goes gummy after such a long period and just about everything will be gunged up, so much so that you will find that about the only thing that will clean it effectively will be lacquer thinners.
Repair Help & Product Troubleshooting for Karcher 3000 Psigaspressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE ONLY USED THREE TIMES IN THREE YEARS. WILL NOT START. HAD CHECKED AND IS NOT GETTING FUEL. ARE THEY BAD ABOUT CARB PROBLEMS. MODEL G2600 P/N 1194-4050 THANKS SELBY


You will have to strip the carb and replace the gaskets and diaphragms. Gas goes gummy after such a long period and just about everything will be gunged up, so much so that you will find that about the only thing that will ... Karcher 3000 Psigaspressure Washer

FRIGIDAIRE DISHWASHER HI! MY NAME IS MARK AND I AM HAVING PROBLEMS WITH MY FRIGIDAIRE MODEL # FDB710LCB0/SERIAL # TH51153536 DISHWAHER. THE PROBLEM: IT DOES NOT COME ON AT ALL LIKE THERE IS NO POWER TO IT. I HAVE CHECKED THE BREAKER AND THE ELECTRICAL CONNECTION AND THERE ARE NO PROBLEMS AT THOSE POINTS. ALTHOUGH FOR A BRIEF MOMENT LAST NIGHT IT DID COME ON AND THERE WAS A "HUMMING NOISE AT THE DRAIN PUMP LOCATION (IT SOUNDED REALLY BAD) THEN IT SHUT DOWN AGAIN AND NOW IT WON,T COME ON AT ALL. A


Check your door switches behind console, next i would ck the circuit board for power in/out. there a tech sheet behind front panel for further diag test points ... Dishwashers

Dishwasher We are having a problem with our Whirlpool ADP5540 dishwasher. We have just moved into a new house with this model dishwasher and have tried running it on a number of cycles. It always seems to stop part way through and the start button then flashes three times. Any ideas what the problem is or how to fix it?


If\015\012this is a blinking "clean light", this is a common problem with some\015\012of the Kenmore\015\012and Whirlpool models. I believe the problem is attributed to water supply\015\012temperatures being too low when filling. Apparently, th ... Dishwashers

My Kitchenaid model KUDK03FTSS2 model is having a problem with the soap dispenser. I have run it three times recently and at the end, the soap pack is still intact in the dispenser.


... KitchenAid Dishwashers

I have a KitchenAid but model # KUDI24SEWH1. Can not find it on your list although another model without the last letters 'WH1' is on it. Anyway, my nephew ordered the parts he said needed to be replaced. One was the top water feed tube and bearing which he had no problem replacing when the part came in. But, he is having a very difficult time opening up the front door to replace the soap dispenser. Removed the 6 screw (three on each side) and the two at the top of the door but that is as far


You don't Use the WH2 just the first 6 letters and numbers.\015\012Jim ... KitchenAid KUDI24SE Built-in Dishwasher

Kenmore Model Ultra Wash Model 665- 45955 Problem: Dish washer leaks at bottom intitially during sudding cycle only...first 5-10 min... then no leaks/drips thereafter thru balance of clean/rise cycle. Whats up....Thought possible seak around washer door is bad but no leaks at bottom or elsewhere after the sudding cycle is completed. Please provide complete resolution reply if possible Tx


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is causing too much suds. Cut ... Kenmore Dishwashers

I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.


Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers

I have whirlpool diahwasher ,model DU1055XTSQ3,quiet partner -1. when i start the machine the folowings things happen: 1.the machine does not start . 2.Start /resume light starts blinking ,after few seconds ( 40-50 seconds), the pots and pans light also starts blinkng .after some time ( 1 minute ) the normal light also starts blinking .All three lights start blinking 3. I have done the following to rectify the problem from the book : alnernatively pressed heated dry and normal keys for


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

We have had three electrical problems in the past 6 months. This one has the "Clean" indicator repeatedly light flashing in a pattern of 6 flashes and then one flash. The dishwasher will not start any cycle, so is out of commission. I am ready to throw this thiing out! Unit is about 3 years old. Model: 665-13422K701


Hi,Most if these models were made by Whirlpool and the flashing clean light is a common error code for them.If the clean light is the one flashing then your dishwasher could have a heater circuit problem (depending on the age) or this cou ... Kenmore Dishwashers

I have a Whirlpool Quiet Partner 2 dishwasher from Lowe's model DV 1055XTVS. The "clean" light flashes three times in a row over and over and the "lock" light is one. None of the controls will work. I unplugged it and that did not clear the problem. How do I unlock/reset the controls?


I have a whirlpool quiet partner 2, its brand new. It leaves a filmy residue on my plastic ware. I use the finish detergent as well as the rinse and no luck. Whats the problem.???????? ... Dishwashers

Whirlpool quiet wash plus dishwasher, (DU915QWDB1) not sure if the model number is correct. Basically my dishwasher will not drain completely (smells bad) and spills water during a wash. I don't know what it is, if there is something easy to adjust inside the washer? Or If there are general troubleshooting tips that I need to run through in order to diagnose the problem? Help!?


... Dishwashers

I have a power washer, craftsman &.0 horsepower, 2900 psi, 2.3 GPM model number 580.752410. i was starter to wash my car, and stops? i change the spark plug, andput new oil in there. still do not working. some one helme in this problem.


... Craftsman 3000 PSI 27 GPM Briggs Stratton Powered Pressure Washer

The original control unit from Bosch' dishwasher SHU4302UC/14 has been replaced after recall from Bosch with a new one that stop working after three washes. It does not respond to any command and shows ''0'' at display. What may be the problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Toro snowtrower with a briggs @ stratton engine model 190402 Will not start Possible carb. problem, fludding, air ? Please advice


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Our dishwasher, GE model # GSD4800, installed in Oct.'03,is emitting a bad odor. We do have a GE disposer, but there are no odors or problems with that appliance. I am not sure if the DW drains thru the disposer or not. Is there anything I can do with the DW (such as look for a drain trap, etc.) or do I just call a plumber? Thank you.


There is nothing within the construction of a dishwasher that can cause bad odours.If\015\012your dishwasher smells it can only be the result of food debris left\015\012within the appliance because of a poor or faulty house drainage syste ... GE Dishwashers

DISHWASHER MODEL # KUDS03FTBL2 WORKED VERY WELL UNTIL TWO TO THREE DAYS AGO DISHWASHER NOW LEAVES MASSIVE FILM AND DEBRIS (LOOKS LIKE FINELY GROUND UP GRAVEL AND DIRT) OTHER DISHES AND SILVERWARE HEAVILY COVERED WITH WHITE FILM ALWAYS USE RINSE AGENT THIS MESS IS A FIRST HAD TO SCRUB ALL DISHES AND SILVERWARE WITH LIME AWAY INSIDE OF DISHWASHER COVERED WITH WHITE FILM AND SOME AREAS HAVE BROWN/WHITE DEBRIS???? IS THIS A DISHWASHER PROBLEM??? OR IS SOMETHING WRONG WITH WATER???? WASHING MACHINE


There is a product out called the dishwasher filtration system. it filters the water going into your dishwasher reducing the hrad minerals that leave that white residue. it is very affordable and works amazing. it goes right under the sink and is e ... Dishwashers

I am having problems with my smeg dishwasher door. The machine is three months old. The bottom left hand corner of the door is catching on the outer wall of the machine and catching and cracking the bottom plastic drip tray. The model is SA8210w


This a faulty installation and adjustment of the door. Whilst it is not directly a manufacturers fault it should be covered anyway, as installation is generally by the distributor or the manufacturers agent.It is also generally condsidered under law ... Dishwashers

Maytag quiet series 200 model MD88750AWB Dishwasher doesn't work. Control panel only responds to the heavy wash button. When pressed it lights up along with three option lights. After about 10 seconds they go off. There is no mechanical response to the pushed button. There were no symptoms leading up to this problem. If you can give me a "head's up" about what to look for before I open up the control panel I would appreciate it. Thank You John


Hi\015\012\015\012\015\012\015\012\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficu ... Dishwashers

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

I would like to purchase a Moyer Diebel U/C dishwasher for residential use. I have the option of purchasing a used dishwasher - it could be one of three models. Which one is the model he is trying to sell to me? 1. 501 HT 2. 501 HTN 3. 501 LT the owner states the voltage is 120/208-240 and heats between 150 f and 180f.He notes there is a 4 ft. cord at the back without a plug on the end of it but the model is rubbed off of the serial number tag.There are three switches on the lower right hand co


The way you mentioned the unit have a 4 ft. cord at the back seem like a 50l LT the best way to determent is open up the bottom plate and see whether there is a booster tank in the right hand side. \015\012Hope this can help you. ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers

Our Asko D1716 dishwasher functions to fill and empty but the pump which causes the sprayers to rotate and distribute the water does not function. The local appliance repairman diagnosed the problem as a bad pump (he called it a motor). Since the pump is a $400 part plus labor, is it possible that the problem is something else like a bad motor capacitor or relay? When the cycle calls for the pump to come on, there is no sound except for a very soft hum.


Hi ! \015\012\015\012Got a D1706 ( in 2002 ) paid $1000 and as os April 2010...same problem as yours, I will trow it away ( dishwasher ) and will never buy at such cost. I'll get a GE or LG. \015\012\015\012Stupid Sweden dish ... Asko D1716 Built-in Dishwasher

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of th ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds