Having problems with your Karcher FactoryReconditioned 1400 PSI 13 GPM Electric Pressure Washer K ?

My Karcher B203 wll not start up - what should i check,,,have checked fuse so far and wonder what to do next !


Answers :

Repair Help & Product Troubleshooting for Karcher FactoryReconditioned 1400 PSI 13 GPM Electric Pressure Washer K

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Karcher B203 wll not start up - what should i check,,,have checked fuse so far and wonder what to do next !


... Karcher FactoryReconditioned 1400 PSI 13 GPM Electric Pressure Washer K

Hello, We have a combination oven and dishwasher. Last week I filled up the dishwasher and after about 5 minutes a blue spark came out at the bottom and it cut the electricity off. Once the electricity was restored we started it again and after a few minutes it just stopped after filling up with water. It blew a fuse again but only one fuse this time and now doesn't switch on anymore. We have emptied all the water from the dishwasher and checked the filter, etc and wonder what could have gone wr


Hi, I contacted the Rosieres web site in France and sent a message using the link Contact Us. Here is the reply;Dear xxxxx,we advice you to contact:TELE MENAGER VIDEO SERVICE21 rue georges Doublet0610 ... Dishwashers

Maytag Quiet Series 100 Help - diswasher always has water in the bottom - doesn't fully drain. We took apart as far as we could down to the hole with the orange washer _ no obstruction. Put it back together and we underneath - and removed drain hose - and checked the drain as far as we could reach behine the anti syphon - no obsturction - wha should we try next?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... Maytag 24 in. MDB5651A Built-in Dishwasher

I CHECKED FOR CONTINUITY AT THE FUSE - FOUND CONTINUITY! WHAT DO I DO NEXT?


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

I have a moffat dishwasher MSD 2000 p00ww I checked the drain hose, ran water trough it had no problem, hooked it back on to the dish washer. I blew into the hose an could see the the air bubbles no problem in the dishwasher. But it still won't drain. Just wondering if you could hep me, on what to try next. Your help would be great.


... Dishwashers

No power to for the controls power is to the machine what to check next. someone told me there is a fuse somewhere?


Hello, welcome to FixYa.Based on your brief description, I'd suggest you likely have a faulty thermal fuse in the control board, but it is not resettable u ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Neff S54E53XOGB Hi there Neff Dishwasher has suddely stopped working. Heard a strange noise during last wash, water did not drain and now the machine will not swicth on at all. Have checked fuse, not sure where to go next.


... Neff Dishwashers

My ikea dishwasher was working fine then the next day nothing no flashing lights have checked the fuse the electricity supply is fine any help???


I got the same problem with mine, have you found solution yet?\015\012thanks ... Dishwashers

I have a candy futura cdf322-80 dishwasher,done a load as normal then i put it on the next day and there was nothing no lights came on nothing, i checked the fuses and the socket they were fine,so i had an engineer out who said there was power going to the machine so he said it was the contol panel which is situated behind the temperature and programme buttons so i bought this part and replaced it but still there is nothing.


I would check for myself if there was power going to the machine. If it acts the ways your does, then either the control panel or the power supply is at fault. Slight possibility a wire that runs between the two may be faulty, but not as common ... Dishwashers

I have a 6th sense dishwasher purchased new October 2004. It has been working properly and then has just stopped the next time I tried to use it - it will not turn on no matter what buttons I push - no response. I have checked the power out let with another appliance and that works so it is not the power supply from the power point. I can only think it must be a fuse or the controller. Can you please advise best course of action? Thanks Helen


I rang the appliance man to fix the problem.\015\012\015\012Thanks anyway Helen ... Westinghouse Dishwashers

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

Kenmore dishwasher... filled up with water and its lights went off.. no buttons work acts like no power. check the house fuse box - ok ... check the 2 door switch - ok .. checked the thermal fuse - ok ... so, i picked up a new board and changed it out. still wouldn't run.


Did you check power to the unit? Double check the common and grounds. When servicing I will disconect(unplug from wall) power to the unit. Is it pluged in? Use another outlet(the outlet under the sink may be wired thru a switch for a disposer)even ... Kenmore 24 in. 16032 Built-in Dishwasher

Hi, I have a Hotpoint Aquarius DWF31 Dishwasher. The dishwasher was put on last night and this morning although it looks liked it as cleaned is has not drained. But now there is no power at the machine. I have checked the fuse at the plug which is ok and also there is power at the socket. Is there a fuse inside the dish washer or any thing else i can check


... Hotpoint Dishwashers

Bimetal fuse The incoming power was blinking off and on due to a storm, it caused the bi metal fuse to fail in the dishwasher when it was not operating, the fuse was replaced with kit #w10258275, now two weeks later the fuse has failed again while operating.These fuses are expensive, I would like to know the value (amps) of these fuses so that the system can checked to try and find out the reason for failure, or maybe you might have an idea where to start. Thanks Tad


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

Bottom of dishwasher is full of water, will not drain. tried checking filter and checked the cone seal. what can I check next?


Next check the drain lines, then the solenoid valve voltage output.If the power going to the pump is in spec, then you are lef ... Dishwashers

My Kenmore Ultra Wash III dishwasher 665.1584990 will not drain. Checked drain hose at both ends and disposal opening and no clog. Pulled check valve and no clog. When running cancel/drain function sounds like working but will not drain manually. What can I check next?


My Kenmore Ultra Wash III won't open the water valve. The pump starts and the heater turns on, but no water. Any ideas? ... Kenmore Dishwashers

Hobart AM14/1 free standing dishwasher with booster. Booster will not heat up beyond 41C. All three heating elements check ok with Ohm meter. High limit not tripped. Temperature screw up at maximum, when you turn the screw, you can hear thermostat click at lower temperature on and off. When turning on main power for dishwasher, heater in dishwasher works fine, but no relays click in the booster tank area. Have not checked for power at booster, have checked all fuses with meter and are ok. Ple


... Hobart AM14-253 Free-standing Dishwasher

Bosch exxcel Last night when i turned on my dishwasher it tripped the fuses in the house. I have changed the fuse in the plug, but it continues to do it. The lights on the display flash up once and then the fuse box trips again. Not sure what else to check. Can any one give any suggestions?


The likely cause of this is a failed heater element which would cause the fuse to blow. You will need to get the heater element checked out and replaced if necessary. A visual inspection of the element may reveal the problem jf not an electrical test ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Hi I have a whirlpool diswasher which is about 7 uears old which has blown the fuse (and the mains trip) half way through a cycle. Replaceing the fuse has resulted not resulted in the restoring of power to the unit. Is there anything simple I could check (in line fuses etc.)? Cheers


Some whirlpool models do have a thermal fuse in the consloe mounted to the main control board housing, might looke to see if it has one and if it is good ... Dishwashers

Whirlpool GU1500XTKT0 dishwasher has a Rinse only led blinking. No functions are responding on the control panel. Keyswitch resistance check table on Whirlpool Service Technician's Tech Sheet checks good with digital multimeter. Door switches and thermal fuse near control module check good.


If your keypad tests, door switches, and thermal fuse are all good, the only test left is to make sure you are getting 120 volts at your control board. Test for 120 volts at terminals p8 and p7, and at p2-6 and p7. You will have to activate the doo ... Dishwashers

Hello. Have a Neff S5457 that is not working properly. It sounds as though it's working but on getting the crockery out, it is obsvious that it isn't. Have checked all the filters in the machine that are easily checked and all are OK. On taking all the filters out, I can see some philips screwheads in the 'sump' of the machine. Wouldit useful to remove these and see what's under the white plastic covers down there? Are there any other areas that I can check or test? I also wonder if the pump is


Clean the nosels of the arm's, check if the tetergent is pumped (if you have an automatic detergent dispenser) check whit dishwasher unpluget!!! you can check and the pump but be carreful how you put it back. also you can check and the hoses to be cl ... Neff 24 in. S5457X0GB Built-in Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0843 seconds