Having problems with your Karcher G3025OH Pressure Washer ?

Will not keep pressure when trigger is pulled.where is the pressure regulator and how do i adjusted it or repair it


Answers :

If u follow the pipe to the pump the releif valve turn clockwise to up pressure
Repair Help & Product Troubleshooting for Karcher G3025OH Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will not keep pressure when trigger is pulled.where is the pressure regulator and how do i adjusted it or repair it


If u follow the pipe to the pump the releif valve turn clockwise to up pressure ... Karcher G3025OH Pressure Washer

The Hom Model No. 308653045 gas-operated cold-water pressure washer has a spring-loaded control on it and I am assuming that this control regulates the output pressure of the water from the pump . . . for example, 1500 psi to 2700 psi. Is it correct to assume that this control regulates the output pressure of the pump. If the control is a pressure regulator, how does one use it and, EVEN MORE IMPORTANT, can one under-adjust or over-adjust the control to a point where THE CONTROL OR THE PUM


... Homelite Pressure Washers

How does one adjust the spring-loaded pressure regulator (?) on a Homelite 308653045 pressure pump. Can it be over-adjusted or under-adjusted, resulting in a breakdown?


... Homelite Pressure Washers

My 3.99 Karcher pressure cleaner seems to keep going on,off,on,off when i release the trigger.It used to keep going momentarly when the trigger was released until the pressure built up,then cut off until the trigger was pressed .Now it goes on ,off,on,off and has decreased pressure.


Hi! robcarrollDid you purge the air from the pump before starting the motor.InMrFixIt ... Karcher 2500 PSI Pressure Washer

My Troy Bilt pressure washer (Model: 020296-01) idle is up and down. When I engage the trigger I get pressure for a second and that's it. If I squeeze the trigger a second later I get the same thing and so on. Is it just the idle that needs to be adjusted or something else?


... Briggs & Stratton Pressure Washers

The motor keeps cycling on and off (about twice every second) when the pressure trigger is not operated. The unit seems to supply plenty of water pressure when trigger is operated.


The motor is holding pressure in the line.Check the manual. I don't think it is supposed to cycle that much.If it's not designed to do that, then there is a seal or a bearing that is leaking.It's letting water pressure escape ... Karcher K2.26 Electric Power Washer

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

Water is leaking from inside the pump and i see no damaged plastic from the outside.the motor keeps on even after i release the pressure gun and most of all ther is no or less pressure when i trigger the pressure gun.please can you suggest what parts do i have to change for it to be fixed 10x


Hello. The internal seals need to be replaced. Obtain the Karcher rebuild kit I got from pressureparts.com\015\012 \015\012J. ... Karcher Quick Connect Nozzle Set

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

I recently replaced the water seals, V-packing & all six check valves in a CW-3504-4MGH pump on a MiTM 3504 pressure washer that had very low pressure. Usually this would fix most pressure problems on most machines, but in this case it had little to no effect. I suspect that the unloaded is the culprit in this case, but since I have had little experience in repairing unloaders (let alone adjusting them). I would appreciate feedback from anyone that has experience in this area. Thanks


Check the wand tip for a tiny piece of debris like a tiny rock or something stuck in the tip. ... Mi T M Pressure Washers

MSV3024 pressure washer backfired after 2 hours of continuous use, then died. i was able to restart it but pulling the trigger kills the engine. i was able to pull the trigger rapidly and keep it running but holding the trigger down killed it again. now it won't restart. can it overheat? it has a full tank of gas.


... Simpson Pressure Washers

Hy; I have a karcher 580 I had to replace gun complete so I bough a simoniz xe01-001 at simoniz.osirus.ca/ for your info 69$ complete ***.I install NOW I get pulse up & down ONLY when trigger is press I turn valve down i only get 10% of pressure if i turn valve up that is when it start pulsing pressure up & down it wont keep pressure up ... Bob...


Most likely problem is that the tip is too small causing Unloader to bypass or restriction/debris in tip. Install clean tip of proper size or 1/2 size larger (example from 2.5 gpm to 3 gpm ) to prevent slow pulse. If tip is clean and /o ... Karcher 2500 PSI Pressure Washer

I have a simpson 3000 belt drive w/ a honda moter.runs great and well taken care of. delivers good pressure, but when not holding the trigger a small burst of air/water shoots out from thehigh pressure overload about every 15 sec. i changed the springs on the system and it checked out o.k. is there an adjustment on the bottom of this overload valve? please return a.s.a.p. Thanks, Pettke deco.


I worked at a tool rental store during my college days and rented a similar unit quite often. I am puzzled about the high pressure valve that you describe. If I recall correctly, the units that we rented had a high temp relief valve. The springs wer ... Simpson Pressure Washers

Honda 5.5 hp pressure washer. After starting and using I let go of trigger and it keeps trying to build pressure until it dies.


Unloader failure replace the unloader ... Pressure Washers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

Dewalt dpd3300 pressure washer - runs for 2 minutes, when pressure builds it shuts down. It i keep the trigger on the wand depressed it runs fine...


... Dewalt DPD3300 Commercial Pressure Washer

Hope u can help when the karcher is conected up and the trigger on the handle is not depressed the machine makes a noise like its trying to presureise the hose it keep kicking in and out i have lost the pressure although it works its not a high enough pressure to be effective


The power washer stops when the gun is closed. This happens because pressure is exerted on a control valve (Spill Valve)...which in turn touches a micro switch and cuts electricity. Now most probably your machine is kickin in an out because the spill ... Karcher K2.26 Electric Power Washer

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

Just turned on my pressure washer model 580 676630 and as soon as i pulled the trigger to start spraying water shot out of a coupling underneath. It seems as if a heal has ruptured. Can this be repair


... Craftsman 2550 MAX PSI Briggs & Stratton Powered

My 2500psi power washer takes forever to build pressure once I release trigger. Is there an adjustment.


See attached link, follow the instructions, this should fix your problem.\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Karcher 2500 PSI Pressure Washer

My pressure washer keeps revving up when im NOT squeezing the trigger. short quick bursts. its driving me crazy. any help?


... Pressure Washers

My karcher k5.55 has lost it pressure and keeps purging when trigger is off


... Pressure Washers

I have a McCulloch FHH18A High Pressure Jet Sprayer that doesn't shut off when you release the trigger, water doesn't spray but the motor keeps running


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0990 seconds