Having problems with your Karcher G3025OH Pressure Washer ?

Karcher Pro Line HD3000 pressure washer ...engine keeps cutting out when spray wand is at full power.. fresh gas, oil is good, cleaned air filter, inlet water supply is strong


Answers :

Repair Help & Product Troubleshooting for Karcher G3025OH Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Karcher Pro Line HD3000 pressure washer ...engine keeps cutting out when spray wand is at full power.. fresh gas, oil is good, cleaned air filter, inlet water supply is strong


... Karcher G3025OH Pressure Washer

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Throttle problems Homelite pressure washer model UT80709A. bought it 10 months ago with no problems and stored it for last 9 months. Before doing so, drained gas, oil. Brought out of storage a few days ago, filled with fresh gas, oil, cleaned air filter. Starts great first try but after about 30 seconds the throttle starts visibly revving the motor a litlle at first then gradually faster and faster until it seems to flood and die. Then you cant start for about an hour and its the same story. Hav


... Homelite Pressure Washers

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

I borrowed my nieghbors power washer. It worked the first day all day. In the morning i filled the gas with a fuel stabiler, and 30 oil. I may have over filled it. Upon turning it on the oil started leaking from the air filetr compartment. It starts, but then smokes starts to fume and all the oil leaks. Did I break it or is it a easy fix. I cleaned the filter housing. Also the filter was soaked with oil. should i get a new filter and install it or what is the solution. need help.


You will need to get a new filter, and drain some of the oil out of the machine. If you over fill these this will happen. 90% of the time nothing is broken. ... Karcher 2500 PSI Pressure Washer

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

MY DISHWASHER HAS NO WATER GOING IN TO THE UNIT IT HAS HAD THE FILTERS CLEANED AND ALL OF THE SPRAY ARMS CLEANED REALLY GOOD DISCONNECTED THE WATER SUPPLY AND FOUND OUT IT HAS A LOT OF PRESSURE JUST NO FLOW ANY IDEA


Hello thereyes i have a pretty good idea i think your problem is that your water solonoid valve has failed and is shut when these solonoid valves fail they automatically shut resulting in no water flow I recommend that you turn of ... Kenmore Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I have a troy built pressure washer leaking gas from the air filter i looked around for advice and hurd bang against the carb and it will realease the float valve i did it and it worked but should i clean out the fuel in the filter area or the filter will it harm it as it is or should it be okay? the filter was soaked in gas dry now and when it happened the gas flowed from the air intake (behind the filter) if i need to clean out in there how do it do it and if i need a new filter


Definetly replace the paper filter and yes Lowes will carry them.if it does not leak now, I would leave it alone or you will be installing a nine dollar kit.The briggs kit # is 294260 is you choose to do it anyway ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Hi I have a karcher 2020b. When power is on it sounds like it is on... When I press the trigger almost no water comes out. When this happened unnoticed oil on the floor afterwards. I have cleaned the filter, the nozzle and flushed the water through to get rid of a possible air lock to no avail. It also smelt slightly of burning plastic - any help would be appreciated. Thanks


... Pressure Washers

The washer will run about 2 min. then die. i have checked the oil, air filter and gas. it has good presure when running then it acts like its out of gas by stalling and dieing. Problems with Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt?


It is possible that the oil pressure switch is not functioning properly or you have a lighter oil in the machine than is recommended.Post a comment if you need more assistance. ... Honda Pressure Washers

Hi The dishwahser does not clean properly. There does not seem to be enough water coming through. I have cleaned out the pump and filters but this has not resolved the problem. Getting a knocking noise as well so checked supply for air leaks but all okay? Help!


\015\012Hi\015\012 \015\012 \015\012If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it’s ke ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Folks, I have a Karcher 5.55 home water blaster that pulses at the highest pressure on the vario power spray wand. It works fine on the lower pressure settings and with the rotary spray wand. I live in a temperate climate, depressurize and drain after each use, always prime the pump, have good water supply, cleaned the filter etc etc. Any pointers on to do or test next? Any help greatly appreciated.


... Karcher Pressure Washers

My gas power washer will not start. I filled the gas, checked the oil, set the choke, made sure it was on, changed the spark plug, checked the air filter, and drained any water. When I pull the cord to start I don't even get a putter. Anything else I can try or do I need to take it to a service place.


Will it run if you pour a small amount of gas in the carb? If so, it's a fuel supply problem. Most likely a stuck closed float needle. ... Honda Maxus Pressure Washer MX5222

No water/pressure Motor runs and pumps for a few seconds then the revs increase and pressure and water fail as if there is no supply.There is a good supply and the input filter is clean


... Pressure Washers

Troy built 2350 psi 2.0 gpm. pressure washer. starts onne then dies. will not start again. has briggs and straton motor. has been sitting up for the winter. have changed spark pulg. checked air filter that is clean, has oil and gas.


... Pressure Washers

Bought unit new last summer. Used it once last summer and once this year. It started fine both times. Today, it will not crank. I have replaced the spark plug, checked the air filter (it is clean), gas tank is full and added oil. Why won't it crank?????


Unable to crank? Do you mean unable to start?If you leave gasoline inside tank over long period of time, that will 'gum-up' and ruin carburetor.To prevent problem, put additive in gasoline or empty gas from tank:: under gas tank sho ... Craftsman Pressure Washers

Intake/Drain light is on. First flashed F13. Cleaned the water intake filter;cleaned the triple filter and drain pump.Light continues to stay on-it seems as if no water in coming in the dishwasher. Water supply is on all the way.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. F13 is a\015\012flow meter error; unfortunately there is no way to reset it so you’ll have to\015\012get ... Miele Dishwashers

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Our bosch shu9902uc dosnt clean the dishes,ive tryed to clean out the drains,blew compressed air thru the drain line,cleaned out the sprayers,still it dosnt clean food off the dishes. water plenty hot and they dry good too it dosnt sound too good when its running too


Make sure you clean the sprayers out real good,if theres debris on the end nozzles they dont spin around too good,also pull out the little service plug that protects debris from getting in the impeller.\015\012i found a little chunk of wood in ... Bosch SHU9922UC Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

Bosch 24in. SGS69LO2 Logixx Our machine runs but there is no water coming into the machine?have removed pipe to check water flow,ok, have removed the filter for the inlet supply,clean.have cleaned all filters and replaced, reset the programs, but still no water into machine.


... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1505 seconds