Having problems with your Karcher K2.26 Electric Power Washer ?

The motor is pulsing on and off without the trigger being pressed

\015 I have a karcher k3.91 and when switched on at the machine the motor starts to pulsate without the trigger being pressed and the is also a significant loss of pressure can anyone help please.\015

Answers :

It is probably sucking air on one of the connections or around one of the fittings at the regulator. You can also turn the pressure up allittle on the regulator, that might stop it also. Make sure the clamps on the hoses going to the regulator is tite. Also it could be that the regulator is just bypassing water and if it has air in it it will pulsate.
I fixed mine works good easy too watch my video step by step i put it on youtube

Repair Help & Product Troubleshooting for Karcher K2.26 Electric Power Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor is pulsing on and off without the trigger being pressed

It is probably sucking air on one of the connections or around one of the fittings at the regulator. You can also turn the pressure up allittle on the regulator, that might stop it also. Make sure the clamps on the hoses going to the regulator is t ... Karcher K2.26 Electric Power Washer

My karcher is a k3.97 and about 18months old. when i'm using it with the trigger pressed it works perfectly but when i release trigger the motor kicks on and off ar regular half second pulses

... Karcher PSI Electric Pressure Washer

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti

I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

Karcher K3.92 M 1750 PSI poweer Washer motor won't start. Followed Reset/Test/Reset sequence with cord plugged directly into outlet. Light on cord near Reset comes on when Reset pressed down but goes off when Reset released (Normal?) Switch ON and trigger pressed releases water stream but no motor action.

They are sensitive to large extention cords. My father in laws pops reset when a small cord is used. If internally shorted- motor will continually pop the reset even plugged direct to outlet. Check voltage at outlet. ... Karcher 2500 PSI Pressure Washer

Karcher 720 mxs fit dirt blaster to gun press trigger pressure low release trigger motor carries on running

... Pressure Washers

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.

... Karcher 2500 PSI Pressure Washer

Hi i have inherited a karcher kb9040.it has only been used 4 or 5 times so i dont realy know how it should sound when. water is suplied to it it surges when you pull the trigger you only get the presure of a good hose pipe jet should the motor speed up when trigger is pressed regards ****

Hi there!\015\012 when you got as good as pipe pressure,you need to accelerate the speed motor to have a good pressurise water for your purpose,the pressure washer has a surge regulating valve as you trigger water gun the pressure blow up, ... Pressure Washers

Hello there.My Karcher pressure washer motor constantly runs with no pressure coming out of trigger gun.I have tried another gun with the same result.The motor should stop/start when you press gun.The model is a 350M plus VPS. Could you please help.thanks

The valve that admits more water to be compressed is stuck. It is likely the O-Rings on it need replacing. No water to the pump, no pressure!\015\012\015\012The motor will stop when pressure is up to the designed pressure. ... Karcher Pressure Washers

Karcher 3100 pressure washer, motor runs fine but when I squeeze the trigger on handle, high pressure pump won't come on unless I remove tip and water is coming out of wand without restriction. Help anyone have any ideas? It did come on once but when I let go of trigger it wouldn't come back on.

... Alfred Karcher Quick Connect Nozzles 2600 3100 Psi 5 Pack

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app

... Karcher 1550PSI Pressure Washer

Hy; I have a karcher 580 I had to replace gun complete so I bough a simoniz xe01-001 at simoniz.osirus.ca/ for your info 69$ complete ***.I install NOW I get pulse up & down ONLY when trigger is press I turn valve down i only get 10% of pressure if i turn valve up that is when it start pulsing pressure up & down it wont keep pressure up ... Bob...

Most likely problem is that the tip is too small causing Unloader to bypass or restriction/debris in tip. Install clean tip of proper size or 1/2 size larger (example from 2.5 gpm to 3 gpm ) to prevent slow pulse. If tip is clean and /o ... Karcher 2500 PSI Pressure Washer

Have a karcher 1750 psi pressure washer. when you turn the on switch on the motor pulses instead of asteady motor sound. when squeezing trigger it sounds fine. can it be the unloader?

... Karcher 1750 Psi Elec Pressure Washer

My Karcher K5000G was working perfectly today but then it began to be slow reingaging the pump when I pressed the wand trigger. Then it stopped engaging completely. The motor runs fine but the pump doesn't engage. What could cause that and how can I fix it? Thanks for any help!!! Moxy

... Karcher Pressure Washers

Karcher k2.35 pressure washer, motor is running, water is flowing, but when you press the trigger only a fine jet of water comes out.

... Karcher Pressure Washers

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.

... Karcher Pressure Washers

I have no pressure when I press the wand handle in. The motor is on water comes out but without any pressure at all. Fix??

... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Karcher 2.56 keeps pulsing on and off whenever high pressure nozzle is attached. I have tried different nozzles and same thing is happening. when i press the lance without any attachment it works fine

Make sure you have bled all air from the system. Also make sure you have sufficient water supply; if house water pressure is too low or if your hose is too long or doesn't allow full flow, you may not be getting enough water to the unit. ... Karcher Pressure Washers

Karcher K 3.99 water blaster. Machine does not start without the trigger being puled. The motor does not turn over

... Karcher Pressure Washers


The bypass valve that relieves pressure when not in use is sticking.Try to back flush pressure washer to see if you can clean some of the gunk that may have built up inside.Sometimes it gets sand in the inlet that sticks it open.. ... Pressure Washers

Frigidaire dishwasher M#fbd1050rem2 - When started water fills for a short while, then makes a constant 'whirring' sound without any wash. This sound seems to be the motor running but no pumping. When cancel button is pressed , unit drains well and complete. Am I correct to assume this is the wash impeller?

... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Karcher k3.68m leaks from the pump area. If I turn it on without holding the trigger down on the wand it will not blow pressurized water. If the motor is idle and the water is turned on then it leaks a lot from the pump area. What part should I replace?

... Karcher PSI Electric Pressure Washer

I have a karcher 7.85 jet washer that has been unused for a while and now fails to work. I have checked plug fuse and replaced the on off switch and condenser as advised previously however there is no life from the motor at all. When the lance trigger is pressed water does flow however this is minimal.

... Karcher Pressure Washers

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not much. This happened after i ran water out of trigger gun with no lance attached, machine switched on. Seems to leak from trigger handle aswell. Many thanks in advance

This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump. ... Pressure Washers

Ran 1600s washer without water.

... Stanley 1600PSI Pressure Washer w 20ft Hose Accessories

I have a DPH3800 Dewalt pressure washer and the soaper isn't working properly. Right tip is being used but when trigger is not pressed it puts water into the bucket. When trigger is pressed it does **** some solution into the hose but very little and very slow. The valve is opened all the way. I know my former partner used bleach in the system which I read in the manual is a no no but it did work at the end of last season. Any ideas?

How is the pump connected on a john deere 3800 psi. i took out the 4 bolts and drained the oil. pump is stuck to cam. how does it come off? ... Dewalt 3800 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds