Having problems with your Karcher K3.450 1800psi Electric Pressure Washer - - ?

My Karcher K3.450 won't build up any pressure - it oscillates on and off. It starts to build pressure, then the pressure drops, and it repeats the cycle over and over at a 2 or 3 second interval.

\015 It has never been exposed to freezing temperatures.\015

Answers :

I fixed mine works good easy too watch my video step by step i put it on youtube
Repair Help & Product Troubleshooting for Karcher K3.450 1800psi Electric Pressure Washer - -

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Karcher K3.450 won't build up any pressure - it oscillates on and off. It starts to build pressure, then the pressure drops, and it repeats the cycle over and over at a 2 or 3 second interval.

I fixed mine works good easy too watch my video step by step i put it on youtube ... Karcher K3.450 1800psi Electric Pressure Washer - -

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!

You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach

Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a troybilt pressure washer when i crank it up it builds pressure when i engange the pressure it takes about 5 seconds and pressure goes away if i let off the trigger it will build pressure again it only has about 20 hours of use on it (i did run a acid solution through it for my driveway wonder if that ate up a seal)

Unloader valve is the most likely suspect here.\015\012Remove and clean with penetrating oil then reinstall.\015\012\015\012Also add some LIGHT oil into your supply hose via a small funnel. 3-in-1 household oil or power steer ... Pressure Washers

Washes for 5 seconds then stops, then starts again intermittently First the heating element started to turn on during the cycle. I never used it before. I changed the setting to unselect Hi Temp Wash but don't remember if it was selected before. The next day the dishwasher filled as usual, washing started for about 4 seconds, then stopped for aroud 10 seconds. The start/stop cycle repeated about 4 times, then all lights went off and nothing more happened.

Bought a new dishwasher... ... Maytag 24 in. MDB7650AW Built-in Dishwasher

When it calls for a drain cycle it sounds like the motor tries to start for half a second and then the display blinks and there is a click. This repeats every few seconds until you open the door. If you wait 15 minutes and close the door it will click once and then drain fine; until the next drain cycle.

Usually the sink connection is not an overflow, it is the main drain\015\012from the dishwasher. It is more likely your s-bend is blocked under the\015\012sink- try putting a bucket under it and unscrewing the u-shaped piece\015\012and cleaning out ( ... Maytag Dishwashers

Diagnostic dishwasher stops shortly after starting a cycle. I start a cycle, it runs water into unit, starts to wash. After 5 seconds it stops, 10 seconds later it starts again, repeats 2 more times, then all lights on panel go out. any help would be greatly appreciated.

... Samsung 24 in. DB5710DT Stainless Steel Built-in Dishwasher

Cycles - pressurizes when trigger is pulled, then motor sets back to idle immediately as if trigger is let go, but is still engaged. Pressure and idling happens within 2 seconds, continously cycling

A lot of commercial and industrial grade pressure washers especially have a safety feature that will either shut down or will return the motor to idle if you do not have an adequate supply of water to the pump to protect the plungers and valves from ... Coleman Pressure Washers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap

Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne

This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

How do I fix a pressure washer that will not build up pressure quickly and when it does reach high pressure, the pressure quickly drops to a lower pressure (more typical of the pressure found in a garden hose)

It can be the inlet filter where your garden hose connects is clogged, so check that first. Also make sure that the hose is connected tightly and not pulling in air both at the inlet and outlet. Remove the spay nozzle and use a pin to make sure it is ... Karcher G3025OH Pressure Washer

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.

... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

2550psi Troy bilt with Briggs engine. Pressure washer runs ok and builds pressure. But, when the nozzle lever is depressed the pressure is strong and then drops to a much lower pressure and a fine spray.

... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an

... Asko Dishwashers

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella

Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Husky 2200 power washer won't maintain pressure. Goes strong for about 5 seconds and then dribbles for about 20 seconds. Then action repeats itself.

... Psi Blue Max 2200 High Pressure Gas Power Washer

Sprays intermittently. electric motor runs, sprays for 3-5 seconds, loses power for 2 seconds, repeats cycle

Clogged water source ... Homelite Pressure Washer. 2700 psi 2.3 GPM Gas Pressure Washer

Using Smart Wash cycle for Kenmore Elite Ultra Wash Dishwasher, machine runs for 3 seconds, cuts off for 10 seconds repeatedly. Is this normal?

... Kenmore Dishwashers

The motor keeps cycling on and off (about twice every second) when the pressure trigger is not operated. The unit seems to supply plenty of water pressure when trigger is operated.

The motor is holding pressure in the line.Check the manual. I don't think it is supposed to cycle that much.If it's not designed to do that, then there is a seal or a bearing that is leaking.It's letting water pressure escape ... Karcher K2.26 Electric Power Washer

Intermittent pressure washer engine seems to work fine, but once I engage the sprayer it cycles every second or two from full pressure to none and back, and the motor seems to rev up and down with it. K

... Karcher 2500 PSI Pressure Washer

My Tecknika Bellissimo dishwasher in wash mode the motor comes on and off rather than run continuously as it used to. So it runs for two seconds, cuts out for two seconds and then repeats this. Other parts of the cycle are normal.

... Dishwashers

The dishwasher trips the safety switch in the meterbox. whirlpool ADP 5000 made in germany (not on the drop down list) the 1st time was after a finished cycle and the power was off in the morning. the second time the power was on at the wall and when thw nob to select the cycle was turned, the power went off. any ideas would be really appreciated. julian

\015\012Please DO NOT touch this machine IF the power is ON. There is a possibility of shock. The reason, the ONLY reason, that the Breaker "Trips" is, if there is a, Phase fault to Earth/Neutral, in other words the CA ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Two problems please: craftsman 2150psi briggs and stratton engine washer, will not start when hot. and secondly, i was washing with regular pressure, then noticed a pressure drop at the nozzle, then the unit shut down. no water leaks at the manifold. water supply was strong. any ideas?

Nozzle dirty, clean out with small diameter wire. ... Pressure Washers

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???

If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Cycles, never builds up full pressure when trigger pulled

If you are sure it is not a bad o-ring and you have re-assembled it correctly then try this.Visit here:http://www.rjbowers.com/parts_manuals/partslist_1190343804.pdfPart # 8 in the pump, karcher # 9.001-187.0 includes a small bullet ... Karcher K2.26 Electric Power Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1445 seconds