Having problems with your Karcher K3.68MR Electric Pressure Washer ?

Change oil karcher k3 - Karcher K3.68MR Electric Pressure Washer


Answers :

Repair Help & Product Troubleshooting for Karcher K3.68MR Electric Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change oil karcher k3 - Karcher K3.68MR Electric Pressure Washer


... Karcher K3.68MR Electric Pressure Washer

How do I change oil to pressure washer? - Karcher 2500 PSI Pressure Washer


At the bottom of engine you will notice a plug take it out and oil will draine out .... replce it then fill at top where u see oil dipstick ... Karcher 2500 PSI Pressure Washer

My Karcher 2400 PSI pressure washer is not starting after about 5 years. What type of spark plug and gap should I change the old out with and what kind of oil do you recommend. I don't think I have ever changed the oil but way less that 50 hours on the machine. Thanks


... Karcher 2500 PSI Pressure Washer

Oil for Karcher K 2.25 Electric Pressure Washer


... Karcher K2.26 Electric Power Washer

I have a Karcher g 2500 vh gas pressure washer and I can't find what oil to use when changing the engine oil. It's not in the owner's manual that I down loaded and I'm not able to find this info on the internet... Can you help?


... Pressure Washers

Change oil on karcher 1900 psi - Karcher 2500 PSI Pressure Washer


... Karcher 2500 PSI Pressure Washer

How much oil goes into pump on a karcher 330m electric pressure washer????


... Karcher K2.26 Electric Power Washer

How Much oil in 720 mx - Karcher K3.68MR Electric Pressure Washer


... Karcher K3.68MR Electric Pressure Washer

Karcher 4400g oil pump change - Pressure Washers


... Pressure Washers

How to change engine oil in karcher pressure washer


... Karcher 2500 PSI Pressure Washer

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

How do I change the oil - Karcher G 2600 VH Gas Pressure Washer


I assume you are talking about the pump. Not good, removepump, disassemble and oil falls out. Put in new oil upside downand reassemble pump, then reinstall. ... Karcher G 2600 VH Gas Pressure Washer

Oil for karcher HD 575 s electric pressure washer


... Karcher Pressure Washers

What kind of oil change? - Campbell Hausfeld 1,350 Psi Electric Pressure Washer With Auto Detail Kit #PW1350


... Campbell Hausfeld 1,350 Psi Electric Pressure Washer With Auto Detail Kit #PW1350

How to change oil Karcher (Robin engine) 2600 PSI Gas pressure washer


... Karcher G 2600 VH Gas Pressure Washer

Karcher pressure washer leaking oil


Usually electric pressure washers only have oil on the pump, so its very likely that you will find the problem there. I'd say check all the pump seals and if that doesnt solve the problem, you can check to see if all bolts are tight when you close th ... Karcher 2500 PSI Pressure Washer

Water pump oil for my Karcher G 2600 OR Pressure Washer?


... Karcher Pressure Washers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

Karcher 395 electric pressure washer lack of pressure


... Pressure Washers

I have a John Deere 3800 psi pressure washer, it stopped having pressure in the middle of a job. No restrictions and still turns on and sounds great. Checked pump oil and it was a milkshake green. Changed pump oil and still doesn't have pressure.


... Pressure Washers

I have a troy build pressure washer model number 020337 Do I need to change the oil in the pump, and if yes how do I drain it and what kind of oil. I know how to change the engine oil


The pump requires no maintenance and no oil change. It is lubricated for life. ... Karcher 2500 PSI Pressure Washer

Lack of pressure in a karcher 455. motor powers on changes sound as trigger is depressed but water remains at mains pressure. oil replaced and had no water in old oil. any ideas.


Most cases the engine is used on many different units find one of those for a pump ... Karcher 4.550-620.0 pressure washer part 45506200/4.550-620.0

How to change oil in a pressure washer


From the manual CleanShot 2050 Briggs and Stratton\015\012\015\012Change Pump Oil\015\0121. Drain engine oil and fuel from pressure washer\015\0122. Use an 8 mm allen wrench to remove black pump oil cap between high pressure ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Changing oil on a high pressure washer with Comet Water Pump


... Comet BXD2527 Pressure Washer Pump

I have same problem with Chicago Electric # 47761 electric pressure washer as Aug 10 2010 writer had w/ Karcher 2500. Runs briefly then stops. Pressure is trapped in hose. I cleaned hose disassembled & greased valve in handle. No improvement. Problem appears to be premature wear of trigger cam in handle - both are plastic. Valve body is rigid nylon. Any thoughts??


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds