Having problems with your Karcher Pressure Washers ?

No pressure HOSE IS BIG ENOUGH,NO KINKS, FILTER IS CLEAN. TOOK THE PUMP APART AND CHECKED ALL THE CHECKS, THEY WERE ALL OK.WHAT ELSE CAN I LOOK FOR? THE PUMP IS A KARCHER-MODEL G 1800 LB Thanks, Art


Answers :

Brother Art,
\015\012
\015\012Try this trick; it always works for me. Assemble the garden hose to the washer, install the HP hose, turn on the water. Now, make sure that there is no air trapped in the garden hose. Manipulate so as to direct any air trapped in the line to the washer. Connect the gun and continue to allow water to "free flow" for several minutes. Now, work the trigger, allowing the unit to rise to "house pressure, and then pull the trigger, dropping the pressure suddenly. This displaces any air hidden in the system. Do this several times, and start the washer up. If this doesn't get you up to pressure, repeat the above on an abbreviated scale, and hold the trigger on the gun down while you start the washer. This should do it.
\015\012Regards, --W/D--
Repair Help & Product Troubleshooting for Karcher Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No pressure HOSE IS BIG ENOUGH,NO KINKS, FILTER IS CLEAN. TOOK THE PUMP APART AND CHECKED ALL THE CHECKS, THEY WERE ALL OK.WHAT ELSE CAN I LOOK FOR? THE PUMP IS A KARCHER-MODEL G 1800 LB Thanks, Art


Brother Art,\015\012\015\012Try this trick; it always works for me. Assemble the garden hose to the washer, install the HP hose, turn on the water. Now, make sure that there is no air trapped in the garden hose. Manipulate so as to dir ... Karcher Pressure Washers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have an older model GE Potscrubber GSD3830Z02WW. There is water dripping from the black housing under the unit during the wash cycle. i have looked at the various web sites at the parts list for this model but do not see anything that looks like this black housing. is this just a cover for the motor and pump assembly?


... GE 24 in. GSD6660GSS Built-in Dishwasher

Have a LG model LD-14AW2 dishwasher which has done good service for many years However, it now sems not to have enough water pressure to operate all the rotary sprayers at the one time - thereby not cleaning properly Have purchased a manual and raken the whole machine apart looking for a partial blockage of the water ways - non found - all looks perfect - still no water pressure I would suspect the pump - however, would have thought a pump either gave full service or stopped - not parti


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Dishwashers

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

I HAVE A GE DISHWASER MODEL#GSD2200G02WW I WANT TO CHANGE THE PUMP BUT CAN'T FIND A REPAIR MANUAL I CALLED A REPAIRMAN AND THEY WANT $300 TO CHANGE THE PUMP CAN ANYONE TELL ME WHERE TO GET A REPAIR MANUAL OR TELL ME HOW TO CHANGE THE PUMP IT DOESN'T LOOK THAT HARD PAUL


... GE Dishwashers

Need to find model of my DW. It is a passtrough with decal on it off and on is rigth side in electrical box. front is closed but can be opend one hadel opens both sides. pump motor below toward back not sideways. Buster is on side. is there manuals available to look up my model number/


You probably have a hobart am-12,13 or 14.Remove the front cover below the door and look to the top right for the data plate,look to the right side door top back for it or look on the outside right of the control box. ... Hobart AM14-253 Free-standing Dishwasher

Bosch dishwasher SHX46A05UC/40 is making noise when draining. I have cleaned the screen and hose back to the drain and removed all debris. So it seem to be the 'drain pump'. But replacing it - now that seem complex - is it? Looks like I would have to stand the DW on its head and remove the base and then replace the pump. Anyone know if I am on the right track? Could it be something else?


... Dishwashers

I have a Husky gasoline pressure washer. The honda motor starts but stalls because the pressure by-pass (not the right term) doesn't seem to open and builds up pressure. I haven't tried to remove any parts yet. I think grit has got in but don't know for sure. The pump looks pretty simple and the part I want to remove for cleaning looks like a plastic hexagon nob. Will this access the by-pass or is it something else.


I think you're right about the knob, but try this:Open the water to the washer. Leave the line open, and hold the trigger down to get all of the air out of the supply and discharge lines. While still holding the trigger down on the spray gun, ... Pressure Washers

We have a leak around the door. It looks like it is around the bottom of the door. We can not find any reason for this. We have checked seals and everything else we can think off at no avaiel. Model 15919. We have found pieces of black stuff on the floor like maybe a protective cover that is deteriorateing . Other then that, everything else is fine. Thanks Dan


... Kenmore 15919 Built-in Dishwasher

Have a bosch dishwasher model shu3032uc-14 doesn't clean very well it seems top spinner doesn't always turn, had service look at it and couldn.t find problem recommended to use a water softner, other people have same unit and do not use a softner and theirs works great what else should i look for thank you


... Maytag Dishwashers

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

I have a model 5000g. it might have 15 hrs. total running time on it. when i tried to use it last it would not build pressure. i took the pump apart and cleaned and regreased it. everything looked good. ive got good pressure to the pump but just a small spray out the wand. when running there is no real load on the engine. it has always been kept inside in a warm enviorment.


... Karcher Pressure Washers

I have a northstar model 1577501-A motor runs great pump will not generate pressure and makes a nasty noise. I have removed the pump from the motor it looks just fine how do I get repair advice? maybe the valve body is messed up


... Northstar Pressure Washers

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

I have a Coleman pressure washer model PWO952750. The connection to the pump for the hose sprayer broke off at the pump. Looking at a parts list I believe I need a Manifold kid. Am I correct ?


... Coleman Pressure Washers

Pump broken and leaking thru crack, looking for used pump for this model


... Pressure Washers

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

I have kemore (whirlpool) dishwasher, model 665.13842K601 after a wash , there is black residue , which looks like black greese in front along the edge.The sears repair person said this normal ??? Daa ! Has anyone else seen this ?


... Kenmore Dishwashers

Dishes are no longer coming out as clean as they used to, especially bowls or utinsiles with dried on food. The machine appears to function ok, but is about 8 years old. The machine just seems tired. Am I looking at a worn out pump or something else?


Hello,\015\012\015\012Those are common issues with dishwasher's as they age, and very good questions. The Asko dishwasher however is a very good hi-end machine and typically good for much more than 8yrs. That being said, 8yrs. is subjective isn't it ... Asko D1706 Built-in Dishwasher

I have a Whirlpool dishwasher, model DU943 that's under 7 years old. I went to use it last night and it won't power on. I tried selecting all of the cycles, but the dishwasher never came on. I looked through the troubleshooting tips in my manual (like checking the circuit breaker for a tripped fuse, which was fine) and I still have a problem. what else can I try? thanks.


Hello- This unit has a thermal fuse inside the door panel on the control. This part is replaceable. If it is bad, replace.- and would suggest not using heated dry as this is most common cause of fuse failure. Let me know if this info helps- have more ... Whirlpool Dishwashers

I have a Kenmore Dishwasher model # 587.1523. For some reason, after washing or rinsing cycles are complete, water is still in the bottom tub. My question is, besides the troubleshotting tips in my use and care guide, is there anything else i can look for or fix myself to help our dishwasher drain?


Good Evening,\015\012Have a Kenmore\\Quiet Standard Model#587.1523 900\015\012Dishes are not getting washed, cyles through , Believe the inside Top Nozzle is not getting any water up the tub to the top of the washer ?? Not sure hoo to fix ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1358 seconds