Having problems with your Karcher PSI Electric Pressure Washer ?

The cleaning liquid has never mixed with the water to pressure water. Do you think the line is clogged and if so, how do I take the unit a part to clear the line?


Answers :

Repair Help & Product Troubleshooting for Karcher PSI Electric Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The cleaning liquid has never mixed with the water to pressure water. Do you think the line is clogged and if so, how do I take the unit a part to clear the line?


... Karcher PSI Electric Pressure Washer

I have a GE Triton XL dishwasher that is not spraying water onto the dishes. I just reset the power, and that didn't help. Putting it on the rinse only or wash cycle fills the bottom with water, but it sounds like a trickle vs. the spray. The heating element comes on and the soap door opens, but there's not spraying. I made sure there was nothing clogging the water line or other parts. What do you think is wrong?


... GE Tritonr XL GSD6260JCC Dishwasher

I have a Frigidaire dishwasher. Model FDB520RHS0, Serial TH92539147. The drum fills with water but will not drain. I purchased the unit about 2 years ago. It has been used sparingly and mostly on light wash. I removed the basket and could find nothing blocking the drain. Is there a fix? Can I replace the drain pump? The unit is making a noise as if it is trying to drain but nothing is happening. I have checked the drain line for clogs and it is clear and the terminal end is conn


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

My Bosch SMU 4000 suddenly stopped filling with water. I had a major drain backup on Thanksgiving and the dishwasher filled with debris. The I flushed the supply line and it was clear so I think perhaps the water valve is clogged or broken but I have no idea what it looks like or how to remove it.


... Bosch Dishwashers

Kenmore model 58715252402 purchased about 3 years ago. Water is not being extracted after a clog has been removed. All parts were removed and out line was cleared.


My GE dishwasher model # 58715142402 makes a whinning sound while running, what would cause this? ... Maytag Dishwasher

I have a bosch SHE58C dishwasher. The cycles all work, it fills so the water line is ok, it washes, and it drains so it is not clogged. I cleaned out the sump and it is all clear. However, I think the "brain" or control module is bad. When I try to run a cycle, it does not fill. One other note is that it continues to run when the door is open. Is there a way to reset the "brain"? I've tried killing the circuit breaker


I have a similar problem with my SHE55M15UC model. I bought it last week and I had to push and hold the cancel button before it would start another cycle. If it doesn't finish the previous cycle, it will not let water in. Also, mine doesn't shutoff ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Installed an older model dishwasher for a friend power works oes throuth the cycles but its not pumping water into the uniT there is no clogs and i hear the pump turn on. unsure why its not getting water into the unit another friend thinks its cause the air tube isnt hooked up but i think it may be something more then that any ideas


You will need to disassemble the bottom part where the bottom rotary spray nozzle is(the part that shoots water upwards). The impeller might have come loose or it is clogged in that area. ... Hotpoint Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

Water drainage I have followed the manual instructions for clearing all appropriate filters on the intake and outflow side but the cycle does not complete and leaves a pool of water in the base. What next? I have the G568/858 Plus Incognito unit (thisis the closest part # to my actual unit--can't even find teh right # listed...), and aI m dealing with the sme issue. I have followed all of the recommended steps in cleaning the filters, traps, etc. There are no kinked hoses. The water drains to b


YOU NEED TO REMOVE THE LOWER SPRAY ARM AND REMOVE THE SHELL THAT IS COVERING THE PUMP AND FOOD SHREDDER ,HERE IS WHERE YOU LOOK FOR A CLOG. ... Miele 24 in. G892SCU Plus Built-in Dishwasher

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

I need to clear out broken glass from the gray pan underneath where the water drains to, but I need to take the twirling water sprayer off first to get to the next piece that looks like it is bolted down, and I cannot see how to remove the twirling sprayer part. The piece in the center of it does not appear to be a screw off part, so I am at a standstill.


Hold the twirling sprayer part and unscrew the big round nut part just above it, then you will see a 3/8 nut,remove it and sprayer arm will come off ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My dishwasher (Optima G2420) had an error F13 for sometime. By turning it off and restarding it would work. But now drain/intake light flashes and nothing is happening. We have checked the triple filter, the filter where water comes in ect. It drains the water but it appears that it cannot take water in. There is a white unit that the intake water goes in and I think that might be the proble.


... Miele Optima G2420SCi Stainless Steel Builtin Dishwasher

When I take a glass or cup out of the dish washer after they are cleaned and heat dried, or a day plus from the cabinet to put cold water,too many small bubles are floating on top the water surface, as a soap-like condition; it clears up shortly. The tech told me it is normal. I think it is not normal because I suspect the rinsing is not totally complete because of the water conservation design. Am I drinking soap-water?


Use a rinse agent., such as jet dry. the owners manual will provide you with the specific location as to where the rinse agent dispenser is locatedl ... Dishwashers

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

Dishwasher will not fill with water. I've already checked the float assembly, that seems to be working fine. The water just doesn't seem to run into the machine. Little history on an unrelated problem: I want to mentioned that not to long ago my brother tried to put a bunch of celery through the garbage disposal. The sinks and pipes got all clogged up and we had to take them apart to clear up. Immediately afterwards the dishwasher stopped filling with water. I don't see how the two can be r


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher ... GE 24 in. GLD5500L Built-in Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

There are two hoses coming from my Bosch SHE45M06UC dishwasher. One is obviously the drain coming from the back of the unit, and the other is attached to the side looped and not connected to anything. I went online to the Bosch website for a installation manual and it describes this hose as a air venting hose. Does the end attach anywhere or does it just hang loose on the unit. My husband detached it from its original position and thought it was part of the water line. HELP!


Many people realize the dishwasher connects to a little hose on the sink, it is called an air gap. However, many people wonder " The air gap is there to prevent the water from being siphoned out of the dishwasher. When water flows through the drain ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1267 seconds