Having problems with your Kenmore 1348 Builtin Dishwasher ?

Mode light stuck on clean. will not start by pushing the start button.


Answers :

Hi
\015\012\015\012


\015\012\015\012

If clean light is blinking 7 times then it may be an issue\015\012with heater circuit, door switch or wash pump. If yes then please reset the\015\012power to the dishwasher. After, 5 minutes check if you are still getting the\015\012same error. If yes, then it is a water heating fault. To resolve this error try\015\012pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High\015\012Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi\015\012Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and\015\012then you press the Cancel/Drain button and allow it to completely drain and\015\012reset.
\015\012If this doesn't work then it's an issue with the wash pump not pumping the\015\012water past the heater efficiently or due to lack of water to heat. Please make\015\012sure that heater is not open circuited and is heating the water efficiently.\015\012You'll have to check the heater using a multimeter; the meter should read\015\012between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is\015\012fine then make sure water pressure is optimum and fill valve is working\015\012fine.

\015\012\015\012


\015\012\015\012

Hope this helps... Please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Kenmore 1348 Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Mode light stuck on clean. will not start by pushing the start button.


Hi\015\012\015\012 \015\012\015\012If clean light is blinking 7 times then it may be an issue\015\012with heater circuit, door switch or wash pump. If yes then please reset the\015\012 ... Kenmore 1348 Builtin Dishwasher

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


... KitchenAid Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Hi! We have a GE Profile PDW9280J0SS with electronic control malfunctions. I can't get it out of the ADDED HEAT mode and many of the other button lights won't light up. I've flipped the breaker several times, and this does (usually) reset the controls to "Normal" and "Heat Dry", but when you push "Start" it switches back to the ADDED HEAT mode. When it goes through this cycle the soap dispenser doesn't open so the dishes don't get clean. I can't use the arrows to select different types of w


Not a specific fix, but I can tell you I have this same exact model dishwasher, since 2005, and it has been services for touch pad button problems at least a dozen times. I am in fact on the phone now with service scheduling another visit because i ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I have a Kleenmaid dishwasher model DW20W and it all of a sudden won't start. The door shuts ok, the power is on and the start light is on. The salt light is also on so we replaced the salt but that didn't help. The cycle seems is stuck on the universal 65 degrees mode and I cant move it forward or backward from that mode. Ive switched it on and off and pressed all the buttons. It won't start. Help?


... Dishwashers

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Dishwasher will not start. The clean light is flashing on and off. If I push the cancel button it appears to be draining but there is no water in the tub and it just continues. When I push the start button if flashes for a few seconds but then goes off. Thanks


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High te ... Kenmore 24 in. 16039 Built-in Dishwasher

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

Diswasher malfunction - won't start clean light flashes 7 times The clean light keeps flashing green. Can't get the washer to start. The only operation it will do, is drain when the cancel / Drain button is pushed This unit is: Stock # 16029 Type # 575-0 Model # 665.16029.402


This information may help in your situation. This can be a common problem on some Whirlpool manufactured dishwashers. The following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 24 in. 16029 Built-in Dishwasher

My clean light is blinking on my kenmore 16029 dishwasher and it won't start after I push the start button. The clean light is following a pattern of blinking 7 times and stopping, then repeating over and over again.


... Kenmore 24 in. 16029 Built-in Dishwasher

I have a Whirlpool GU1100 built-in diswasher that will not clear the pot & pans selection. It is stuck with the pots & pans and the cancel buttons lit and blinking. It will not start or clear. I have tryed to shut the power off for awhile and this has not helped. Other buttons can be pushed and will light but the other two remain blinking. If the clear button is pushed it will clear the other button but not the pots & pans or itself. Is this a problem I can fix myself?


... Whirlpool Dishwashers

The dishwasher does not start. Push the start button and the active light goes on but does not start. Light soon moves to clean.


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I have a Quiet Partner II dishwasher. The clean button is blinking with a green light. When I try to start is over, nothing happens. When I push the cancel/drain button, I hear something happening for maybe a minute, then it reverts back to the clean button blinking and won't take any other commands. What should I try next?


... Kenmore 24 in. 16222 Built-in Dishwasher

Frigidaire Dishwasher gld2440reb1. After removing filters, cleaning and replacing them I had three flashing lights ie Sensing, Clean and Sanitized. all buttons were inoperable. after unplugging and reconnecting I had a PF or power failure indicator. after pushing the start button the PF went off but no further action from any button. Help!


Usually if you get a PF error that means you have received a power failure usually from the control board shorting out on this model. Typical reasons the control will short out is from either the circulation motor shorting or pump motor shorting. If ... Frigidaire Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1660 seconds