Having problems with your Kenmore 15073 Stainless Steel Built-in Dishwasher ?
Removal of pump casing
\015 Upper arm does not rotate. I have removed the bottom arm and top plate and found some rubbish in the sump but I think that the problem may still be material inside the pump itself. \015\012The pump casing is held by a screw on one side and a plastic latch on the other.\015\012I have been unable to remove the casing. The retaining screw comes out easily enough but using gentle force in various ways around the plastic latch fails. \015\012I note that the casing is very firmly against the body of the unit which leads me to suspect that a special tool is required. \015\012Does anyone have any suggestions on removing this casing.\015\012thank you.\015
You Can Remove it with a screw driver,put a small flat head screw driver in the slot to the right and push to the left to unlock catch on bottom and pull up on unit.
Repair Help & Product Troubleshooting for Kenmore 15073 Stainless Steel Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have removed the recirculation pump of my Neff S54m45x5GB/82 dishwasher from the casing and have got the sealing kit and a new pump as water was entering the pump as the seals where worn but now I seam to have difficulty reasembling the pump into the casing any tips
Removal of pump casing
You Can Remove it with a screw driver,put a small flat head screw driver in the slot to the right and push to the left to unlock catch on bottom and pull up on unit. ... Kenmore 15073 Stainless Steel Built-in Dishwasher
My troy bilt pressure washer only runs a few seconds then dies.I thought the pump was plugged so I removed pump.While pump was off I ran the engine in case it was a fuel issue,The engine ran fine.Whic
... Pressure Washers
Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force.rnPROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump o
... Kenmore 24 in. 16193 Stainless Steel Built-in Dishwasher
Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump
... Kenmore 15529 Built-in Dishwasher
Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump or i
... Kenmore 15529 Built-in Dishwasher
Wash pump motor removal to clear wash pump of a large object.we have washer out of cabinet on it back on the floor. Need to remove wash pump motor to access wash pump to clear a large object from the pump rotors.
... Whirlpool GU2300XTS 24 in Builtin Dishwasher
My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.
Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers
GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!
You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher
HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert
... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher
Hi, we have an Asko D3122 dish washer, pump runs continuously and light 2 flashes(cup and saucer) have removed machine and tipped out water, checked pump hose and removed pump is clear, we have
... Asko D3122XL 24 in Builtin Dishwasher
Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.
Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers
My Bosch Dishwasher SHS6902GB fails to pump water both in & out. I'm now down to the pump rotor. The limited user manual talks of removing food debris but there doesn't appear to be any stopping it? How can I remove the pump to see if this the problem or recommendations? Thanks
... Bosch Dishwashers
Drain pump i bought a new frigidaire dishwasher and setting it up... i removed the drain hose from the drain pump and noticed the pump outlet has a thin rubber diaphram...should i remove it....set up instructions say nothing about it...ty....tim
My husband did remove ours,and we too have a frigidaire 18" built in dishwasher. But ours won't drain, he says it might\015\012be the pump, but he is hoping not.. everything works except when its draining. water just sits there in the bottom.. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher
We ran a cycle with 'Lemi Shine' a hard water treatment (Lime remover). After that cycle, the tub will fill and drain, but the water does not reciculate. So, I assume the deposits loosened and then clogged either the recirculation pump or a sensor that activates it. I don't know how to determin that or how to access the senors/floats. I do know if it's the pump that's clogged, I have to remove the thing and flip it on its top to access, but don't know the details.
Hi. Both the drain hose and recirculation hoses should be checked, asap. These hoses are connected to the pump assembly and they can also both become obstructed, as well. I would purge these hoses and check the pump filter and fine particle screen fo ... Bosch 24 in. SHY66C05 Stainless Steel Built-in Dishwasher
Hello: I have a ge gsd5500 dishwasher. I want to remove the pump connect which is leaking. Key 455 This connects the pump to the main tub in the middle. How do you remove it? Thanks
Remove dishwasher from under the cabinet. Turn dishwasher on it's side. Loosen the clamp holding the motor/pump from the pump connect. Loosen the clamp holding the motor to the sump. Carefully remove the motor from the sump and pump connect. Tur ... GE 24 in. GSD5500G - Multiple Color Built-in Dishwasher
GE TRITON XL NOT DRAINING-CHECKED AIR GAP AND HOSE TO DISPOSER. USED BASTER TO REMOVE LOTS OF WATER THAT SMELLED REALLY BAD ON ONE RINSE LIKE BACKING UP. CLEANED SCREEN AND AREA IN PUMP AFTER REMOVING IMPELLER (SP). WATER NOT EVEN COMING UP THROUGH DISPOSER. BAD PUMP?
... GE Tritonr XL GSD6260JCC Dishwasher
Broken glass went through pump cover openings. How do I remove this cover to remove the glass. My model # is 565.13572K700. I don't want to run the dishwasher with the glass particles inside the pump cover.
\015\012Hello,Welcome to FixYa. ... Kenmore Dishwashers
Hi I have a Siemens SE26T252GB/01 dishwasher which won't drain. (The "check water" light comes on). I have checked all the filters/drains and I think the fault is the drain pump which I would like to replace. I can remove the side panels but cannot remove the base to get access to the pump. Can someone help with instructions or a diagram please? Many thanks
... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher
Asea Cylinda 1400 dishwasher leaking underneath. Found wash pump seal leaking. Have removed pump and motor but can't remove impeller to get to seal.
Our whirlpool estate diswasher will not drain the water after a wash cycle. I have removed internal parts down to the drain and cleared the path. Moreover, I have removed the drain tube and clean it. Still water will not drain. I assume it is the pump. Can the pump motor be easily replaced? Thank you, Jim
You hve to find the right pump first ... Whirlpool Dishwashers
My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc
Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers
Kenmore dishwasher model 665.16033401 doesn't drain well. Drain pump comes on but drain water only trickels out slowly. Obstruction somewhere ? Removed rotating spray arm inside to try & get at the place where the drain water enters pump. Can't remove any parts beyond spray arm. Home: 330-865-4813 Cell: 330-608-3022
Cancel wash working fine. when ready to wash get humming sound. pumpmotor not turning. A glass dish broke a week ago and work fine till know remove screen today found some small brokeb glass - like when a harden glass brakes? if something is in the pump how do i remove pump
In\015\012most dishwashers, the water pump is located under the lower sprayer\015\012arm. This component pumps the water through the dishwasher. The pump\015\012has two impellers, top and bottom. These, as well as other components,\015\012can become ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher
Trying to access the pump for a SGS43T12GB/08, the Bosh help desk are saying remove a screw once the roraty arm etc has been removed. We cannot see anything, help on how to access the pump would be appreciated
Typical of the Bosch help desk, the instructions given to us related to the previous years model where access was via the filter etc.\015\012\015\012Managed to find, on a different website (sorry), a similar problem from 2005 in which you ... Bosch Dishwashers