Having problems with your Kenmore 15129 Built-in Dishwasher ?

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Answers :

Hi,\015\012
\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes in contact. Also check for cracks in the shielding or exposed wire. If you find anything faulty you have to replace the cord.\015\012
\015\012The door latch pulls the door tightly closed to prevent water leakage around the door. It is also designed to prevent operation while the door is open. The door latch works in concert with the door switch to ensure that the door is tightly closed and latched. If the door latch is not properly aligned it may not pull the door tightly closed and the door switch will not be fully depressed. Unless the switch is fully depressed the dishwasher will not operate.\015\012
\015\012
\015\012Thank you !!
Repair Help & Product Troubleshooting for Kenmore 15129 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Nordmende dish washer model no. DWSN60WH . when power button is switched on machine gives a buzzing noise for about 10 seconds while the start button is still lighting. Noise stops and light goes off and then wash and end buttons start flashing continuely.


... Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

The Start button does not light up, yet the left side did light up for wash cycles. I'm guessing the PC Control board has some issue with touch button panel, as a faint high pitched shrill can be heard from the board after I took the door off and put my ear to the board. Also, over time the left side of the panel stopped lighting up too, so I through the circuit breaker. Can you advise which component it is. I'm guessing the faint high pitched shrill is the PC COntrol board attempting to communi


You have a faulty touch pad that will need to be replaced. Below is a \015\012link to a video you will want to download so you can see how to replace \015\012the touch pad.\015\012\015\012\015\012\015\012 ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

I just started a light wash cycle on my Kenmore Ultrawash model 665.1359. The cycle stopped suddenly and now the heated dry button is flashing. I tried pressing it for 10 seconds, but it won't stop. I cannot get the dishwasher to resume its cycle. What do I do??


... Kenmore Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1684 seconds