Having problems with your Kenmore 15632 Built-in Dishwasher ?

I have a kenmore 15632 and my problem is that the dishwasher has power and as soon as i close the door the lock on lights up but when i go to press start it will not start. Now we tried unplugging the dishwasher and plugging it back in but we still get the same result. if any one can help it would be well appreciated.


Answers :

Repair Help & Product Troubleshooting for Kenmore 15632 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No power the dishwasher is not getting power. The plug is hot, the breakers in the house are all ok and we've unplugged the dishwasher and let it sit several minutes and then plugged it back in. Still no power to the console of the dishwasher. Model # 665.16053402


Well if your main power that supplies the dishwasher is good then you need to replace the main control unit of the dishwasher ... Dishwashers

I have a kenmore 15632 and my problem is that the dishwasher has power and as soon as i close the door the lock on lights up but when i go to press start it will not start. Now we tried unplugging the dishwasher and plugging it back in but we still get the same result. if any one can help it would be well appreciated.


... Kenmore 15632 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Soap gets stuck inside the soap dispenser, so that at the end of the cycle, there is a clump of soap still in the dispenser. We have also noticed that the rubber seals at the back of the dishwasher (the ones that the spin arms plug in to) are getting worn. Will get new gaskets this week, but wondered if the soap dispenser isn't another problem.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

ADP 7570 dishwasher I keep getting the F7. its trying to start but it won't fill. I removed the side panel and disconnected the plug as instructed and plugged it back in replaced the panel an it still won't start.


... Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

My dishwasher KUDi01IL is having trouble with the electronics...only the cancel button will work. The other buttons are no longer lit, but occasionally I can get the "normal" wash button to light..however, the machine will not start. Called technical support last night, tried unplugging and plugging back in due to possible power surge or storms....it did not help. Please advise.


Hi,As we are not there, we can make some intelligent guess. This is a common problem in Dishwasher.There might be million of reasons for the same and to be frank you would agree. Let me put down some main reasons which i have found ;- ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a kenmore elite dishwasher model # 665.13103k902. It was working just fine & then one day I ran the cyle and it lost all power in the middle of the cycle leaving water standing in the bottom. My husband checked the breaker and also unplugged it and plugged it back in and still nothing...any suggestions?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

When I turned the dishwasher on the lights started blinking and making a noise. When I opened it back up, lights are still blinking and now it is beeping every 30 seconds. I have tried to reset the dishwasher and have even unplugged it. It is still blinking and beeping. Any suggestions?


... GE GLD4100MBB / GLD4100MCC / GLD4100MWW Built-in Dishwasher

My dishwasher after the cycle is over still have a bit of dirty water remaining on the bottom. After few hours is getting more and more dirty water. I have a feeling that some kind of the valve is not working correctly which allows the water from the sink drain to come back? Am I right? Is it a big re[pair or marginal? My dishwasher is about 20 + years old and still the greates one I owned ( I had before Bosh ). I own the dishwaser for last 4 years but previous owner loved it and never repair


Hello Ma'am/Sir,\012 The Best thing you're going to do is to have new Dishwasher.A lot of brand new products can help you, rather than striving the old one...Hope it will help you! God Bless you...Thank you! ... Miele Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

I have a Bosch Dishwasher SHU3302UC/14 that will not drain. We initially thought the problem was the disposal because water kept backing up into the sink. We replaced the disposal, removed the dishwasher plug in the disposal, but the dishwasher still does not drain. I would like to check the drain line, but am unable to access it. I removed the kick plate and the screws that secure the dishwasher to the underside of the counter, but the dishwasher will not move. Can you access the drain li


... Bosch Dishwashers

Hi i have a problem with my bosch dishwasher model no.5600 061 333 en(8311), there is no power light and not functioning with any mode and when plugged in it makes a big flash sound from underneath. The plug fuse is still intact. The plug has also melted the plastic backing plate when plugged in. Could you tell me what the problem is and how to go about fixing it. Thankyou.


... Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

ASKO d 3122.. Keeps filling up the overflow area on the bottom of dishwasher. WHich sets of the overflow switch, then i get the flashing tea cup again. I will empty the over flow area. It will reset, We get one good wash out of it then on the next load it will stop work ing again and get the flashing Tea cup again, Back to unplugging the unit and draining the overflow area again.


... Dishwashers

Kenmore dishwasher My dishwasher stopped in the rinse cycle and no longer appears to be getting power, although the breaker works and the plug it is connected to is still receiving power. Is there a reset button for the motor, or some other idea to try and fix this? Thank you for your assistance. Mark


Mark, you probabley blew the thermal fuse located on the main board. Easy fix. Part number 8269213. You can ohm it out to be sure. You have to remove the inner panel to get at the control board. The fuse sits on the top side and clips on. Two wires ... Kenmore 24 in. 16293 Built-in Dishwasher

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher

My G865 Miele dishwasher goes partway through the cycle then gets hung up and runs without advancing. We left it running when we left for vacation and it was still running when we came back. I'm assuming it is the timer mechanism. The dishwasher is ten years old but has been run only every other day or so. Is it worth fixing or is it better to replace?


It will cost alot to get repaired,10 years old you got money out of this one. ... Miele 24 in. G865 Built-in Dishwasher

Fphd2481kf control won't reposed. I unplugged it for a few hours to get it to reset. When plugged back in the pf code was shown. I opened and shut door to clear code. U cannot get it to respond to any input and it doesn't show any codes.


... Frigidaire FPHD2481KF Builtin Dishwasher

I have a whirlpool dishwasher model adp 5550 condenser. The dishes do not get clean. I have had a repair man out twice and he replaced the soap dispenser on Friday but it still doesn't work. I went to the store today and bought every cleaning things I could find for dishwashers and also started to investigate online myself. I took the arms off and cleaned them, I took the filter out and cleaned it, and then I noticed that the plastic bar that runs from the top, along the back and into the bottom


... Dishwashers

I have a kenmore ultra dishwasher 655.177779990 and the lock out light was flashing until I unplugged all connectors and plugged back in. Now light stays on and everything else has stopped working. Tried to reset but no luck what can I do to reset dishwasher?


Hello & Welcome to FixYa\015\012\015\012\015\012You\015\012are right, the unit needs a reset. To reset the control you can press and hold\015\012the AIR DRY/RINSE ONLY button for 15second ... Dishwashers

Dirty dishes the dishwasher sounds and appears to be operating normally but the dishes are not getting clean. now i've noticed dishwasher soap still in the dispenser after the washing cycle has been completed. I'm thinking maybe i have plugged water jets? Anyone have any suggestions? Thanks.


Plugged jets, possiblemore likely it is leftover food reminance left in the pump area. and on certain dishwashers it could be a swollen check valve, not allowing the evacuation of the used dirty water.does your soap dispenser open? ... Dishwashers

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1729 seconds