Having problems with your Kenmore 15634 Built-in Dishwasher ?

Final rinse water does not leave dish washer. Also on a test run with no soap added, there is soap & water in bottom of dishwasher.


Answers :

Repair Help & Product Troubleshooting for Kenmore 15634 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Final rinse water does not leave dish washer. Also on a test run with no soap added, there is soap & water in bottom of dishwasher.


... Kenmore 15634 Built-in Dishwasher

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. Also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Best off to call a certified repair company such as Sears. ... Kenmore 15899 Built-in Dishwasher

My Professional series dishwasher does not work properly. It is only 1.5 years old and glasses on top rack get sprayed with fine layer of particles every time I use it. Other items, top and bottom, are often not clean as well, but glasses are the hardest to re-clean. I have tried evacuating the water left at the bottom of the dishwasher before running, pre-running the hot water in the sink and ensuring that the disposal was run, removing and cleaning the filter at the bottom of the washer. None


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire PLD4375RFC Dishwasher

Dishes and the dishwasher look dirty after they run, like it redistributed dirty water. The door is very dirty/filmy except right under the soap dispenser, like someone squirted dirty water on it but wiped right under the soap dispenser. If I run it a second time with vinegar it gets clean, but that is crazy, esp since it takes 2 1/2 hours a load. I have 2 of them and both are doing it. I have changed soaps, added more soap, used less soap, pre-rinsed dishes, put them in filthy, used jet-dry, no


Hi Mike_wend604,\015\012\015\012I am looking for a used Asko #1504, if you would like to sell yours please e-mail me at [email protected] and put "Asko" in the ... Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I stopped using my dishwaser because it left crusted on food particals even tho I rinced them well(so I thought) before loading. It was as if they were just being dried crusty. After a couple month I noticed a bad smell. I looked in the dishwasher to find standing water in the bottom. I ran a little CLR through and it cleared out. But a couple weeks later again there was water in the bottom. It seems as if the water from the sink is draining into the washer. If I run it it runs thru just fine, n


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Estate 24 in. TUD4700KQ / TUD4700KB Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

After I run the dishwasher, water stands at the bottom and it smells. I have had the dishwasher for five years. The washer seems to be working properly it's just that water stands at the base of the washer. Is it normal for water to always stand there?


No it's not normal, you are probably having some cloge in the drain pipe, you could try with a pice of wire to pick it up or hose it down, or use some comercial unplaguners like mr. muscle or something like that, i think that this would do the trick ... GE Nautilus 24" Built-in Dishwasher

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.


Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

Dishwasher repair Dear Guru, I hope you are well this evening. I have a Whirlpool Quietwash Plus dishwasher (940 Series) that will randomly have water sitting in after running through a washing cycle. In addition, some mornings there will randomly be a couple inches of water sitting in the bottom without every running the washer. Need assistance. Any help will be appreciated. Thank you for your time. J


Without model unablr to look up exact unit, but in genreral, either ther is a blockage/clog in oyour drain line not alowing complete drain of cycle, as far as never really washing, i would look into perhaps a faulty/ sloppy door switch assembly. if f ... Dishwashers

Lately the soap remains in the dispenser, dried and caked in (I have to dig it out with a sharp object, as it becomes a solid piece). I have also tried gel soaps, but find them in the bottom of the dishwasher, partially intact. The mistery is this does not happen all the time, but most of the time! I've checked the water pressure and the water temperature: both seem to be fine. The dishwasher does run a full cycle. Is it time to buy a new one? Would you also be able to tell me what year this mod


... Frigidaire 24 in. GLD3450RD Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Have the Kenmore Limited Edition dishwasher, model # 665.15892100. When dishwasher is running, you can hear the soap container flip open. However, @ end of washer's completion, and main door is opened, the soap is still in the container. Some has leaked out, but the majority is still in the container. Dishes are still dirty, so it appears that either there is no water to disperse the soap, or does the door really open? Any ideas?


Check the wash arms to see if food has not cloged the holes stopping water getting through\015\012if these are clean the machine may not have enough water entering machine\015\012also check how you stack machine ... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

The is for the model: DDW1899WP. The cycle is getting stuck in the first phase and the soap container is not opening. When I open the soap contain, water has seeped in because the soap is moist and hard rather than loose and powdered. In addition, water is pooling int he bottom of the dishwasher. I tried adding more rinse aid because that has solved the problem in the past but it is still persisting.


Looks like there are two problems here\015\012\015\0121. the controller is not sending a signal to open the soap dispenser door at the right time when the water is flowing through it\015\0122. the drain motor is not pumping the wate ... Danby DDW1899WP Portable Dishwasher

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have an LG ldf7811st dishwasher. My bottom arm spins with water, my middle arm does not spin but does have water coming out, and my top arm doesn't spin or have water. I have just finished taking apart the arms, the supply to the upper arms, the filters and the impeller. I cleaned everything and nothing really seemed clogged. I have tested it since and it still has the same problem. I know that they aren't spinning because i placed them in a certain position before i ran the test run. They


I'm thinking like you're thinking, that it's something affecting the water pressure, but you've done everything in the upper section, so the problem must be from below, unless you have a leak somewhere you haven't noticed and are losing pressure beca ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.3046 seconds