Having problems with your Kenmore 15762 Dishwasher ?

On our Kenmore Ultra dishwsher 15801 the plastic ring at the bottom of the rinse arm is broken


Answers :

Repair Help & Product Troubleshooting for Kenmore 15762 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On our Kenmore Ultra dishwsher 15801 the plastic ring at the bottom of the rinse arm is broken


... Kenmore 15762 Dishwasher

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

Hi Model DU1048XTPQ4...when I started the DW today, it sounded kind of loud. I let it continue, then I smelled something burning. What I think happened is that the lower spray arm is too loose-so when it spins, it gets stuck on the heat ring on the bottom of the DW and then the plastic parts start to melt. We disassembled the spray arm and there was lots of calcium/lime build-up. So we cleaned all of that out, put it all back together, but the spray still seems too wobbly. Went ahead and start


The noise coming is from the motor bearings or the impeller which moves with the motor.both has to be checked.\015\012if the bearings are making noise motor needs replacement and if impeller is cracked it needs replacement.\015\012you can get require ... Dishwashers

I have a Kenmore Ultra Dishwasher. The bottom arm spins, the top doesn't, although water drips out. The water fills up under the heating element. The top dishes aren't getting clean and the bottom aren't as clean as they used to be. I also noticed that the soap dispenser is open, some of the soap is gone, but there's still some soap in left in the dispenser. This never happened before and it happens all the time now. Thanks for any help you can give me!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

Our Kenmore dishwasher 665.1726 doesnt seem to be cleaning as well. LAst time this happened a serviceperson cleaned out a filter where food debris had clogged the water flow. We were able to take off the bottom wash arm but couldn't figure out how to get the filter off (there are 4 screws holding it in place and one is under the plastic arm that caries water to the sprayer.


I had the same problem!\015\012\015\012The arm WILL come off....you have to pull the screen off. ... Kenmore 24 in. 15689 Built-in Dishwasher

How do you remove the lower spray arm on a Kenmore Ultra Wash (665.17019.402)? I was told to hold on to the plastic screw and spin the arm counterclockwise to remove, but I've been spinning and spinning, at leat 100 rotations, and it is not coming off. I've uploaded pics so you can see the apparatus. http://picasaweb.google.com/gregoryor/Dishwasher?feat=directlink


Hi, In the center of the spray arm is a threaded piece of plastic/bolt.\015\012Use pliers and turn that tab on the bolt. If it doesn't turn easy. Holt the bolt and try to turn the spray arm with you hand.\015\012It will release the spray ... Dishwashers

My Maytag MDBH965AWW Legacy Series 300 is making a loud grinding noise. I took off the lower spray arm and other parts below it to see if something was lodged near the chopper blade. What I found was broken plastic pieces from the bottom of the filter/flowplate assembly. It appears that the chopper blade is coming in contact with the filter/flowplate assembly and therefore the chopper blade is chopping away at the bottom of the filter/flowplate assembly. What do you think the problem is? Ho


Here is the break down view of what you have. The only way to fix this is to get to the chopper and tighten things up. Look at the photos and you can see the chopper and how to do it, it's a bit of a job...Remove Chopper Sleeve by using I ... Dishwashers

I have a broken plastic door latch on the kenmore ultra wash dishwasher model # 665.1303? Is that common? And will the warranty cover it? It's only 8 months old.


... Kenmore Dishwashers

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

10 yr old Kenmore dishwasher was leaking, cycling ok but dishes are not coming out clean. Took about bottom spray unit, found a split plastic round ring about 1.5" dia. Could this be the problem or what else do I need to check?


The ring fits just under the spray arm and the split is normal. When you tore the spray assembly apart, did you clean the screens at the bottom (if white hard-water deposit, soak in 50:50 hot water and white vinegar)? Make sure none of the ports in t ... Kenmore Dishwashers

My Kenmore under counter ultra wash dishwasher model 665.15825691 has started leaking at the lower corners of the door. The leaks seem to occur during the final rinse while the water is being heated. I have tried cleaning out the door bottom and the tub edge where the door and tub interlock. There is no gasket in this area.


Happened on my dish washer too. Remove lower rack, remove lower spray arm by removing the center plastic nut, check screws (torx) on outside edge of pump. Tighten these as necessary, mine were loose causing water to spray forward against the tub c ... Kenmore Dishwashers

How do I remove bottom spray arm in a Kenmore Ultra wash dishwasher 665.1345


... Kenmore Dishwashers

Water tower The water tower came off of my Kenmore Ultra Wash III dishwasher. I cannot figure out how to get it back on. There is a gasket on the water arm. Does the water tower actually go on top of the bottom rack? And if so, then how?


I had the same problem finding a Water Tower laying in the bottom of the dishwasher. Solution is to simply lift the bottom rack and insert the tower into the center-most square hole. Twist the tower with the large lip on the bottom of the rack and th ... Kenmore 17439 Built-in Dishwasher

Plastic rotating sprayer is laying in bottom rack. How do I reinstall? It a kenmore ultra wash III. Do you have a parts diagram of the interior racks and sprayersso I can see the assembly of interior


Yes you can go to sears parts direct .com. it will give you a pic image .let me know if this was helpful ... Dishwashers

Kenmore ultra wash #15765 will not drain. purchased 1996, web says no such model exist, but i have the manual, and it does, i need help . I have taken out the lower sprayer arm and the spinner that chops up the food left, even removed about 10 screws that hold down what looks like a filler but it did not allow me to remove it. How do i access the drain to see if it is stopped up. Do i need to pull it out from the counter and go from the drain hose,or somehow go in from the bottom??


... Kenmore Dishwashers

Model 587784100 My 18inch Kenmore apartment-sized portable dishwasher leaks when running and needs a new main rubber gasket (where the door seals the washer), and a new collar of some sort of white hard plastic collar at the very bottom of the spinning washer arm (which I believe helps make it spin more freely and not "chatter"?) My question is: Is it possible foe a handy person to replace these parts (looks fairly easy), or should I get a proper Kenmore/Sears repairman to fix it?


If you think you can do it then do it. it is normally not any harder than it looks. now because i work there i would say call them :) but you can change those parts fairly easily ... Kenmore Dishwashers

Top rack in my Kenmore ultra wash is not getting clean. Checked upper spray arm and it is not plugged with any debris. Bottom rack is fine.


Did you check the tube that carries the water to the spray arm? ... Kenmore Dishwashers

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Maytag dishwasher MDBTT50AWS Door Latch broken. Screws hold the top. The bottom appears to fit into ''plastic teeth'' . Are the teeth supposed to have top and bottom or just bottom teeth. It appears mine has broken teeth on bottom. Is so, do I need to replace control panel to hold latch at bottom.


... Dishwashers

I have a 12 year old Kenmore Ultrwash Model #665.15951790. I recently replenished the rinse aid dispenser and am experiencing an oversuding problem. It was oversuding to the point that suds were coming out the bottom of the door. Did notice that the blue rinse aid seemed to have leaked into the dishwasher due to a puddle of blue rinse aid at the bottom of the dishwasher. Have run a "quick rinse" cycle 4 times with no dishwasher soap added and still have sudsing. Can the rinse aid cause oversudin


... Kenmore 15129 Built-in Dishwasher

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

How do we install a door balance kit on our Kenmore Elite dishwasher? Model is made by Whirlpool I understand. The plastic pieces are broken. The wheel and the spring are okay but the plastic piece on the string is broken and another plastic oval shaped piece broke as well. We plan on ordering a kit but don't know how all of the pieces go together.


... Kenmore Dishwashers

Only 10 months old - the middle spray(plastic) became disconnected to arm on back wall. Is there only a small o ring that hold this arm on? When I reattach the arm is very wobbly. Just need a new o ring or is it more complicated?


... Miele G 1182 SCVi 24 in Builtin Dishwasher

I see the pressure tower for a Kenmore Ultra Wash Quiet Guard dishwasher laying in the bottom of the dishwasher. I've just rented the house and haven't used the dishwasher yet. Does this pie


No, the designers put it in there for a reason; it won't work as well without it, as it would with it in. Probably the mounting tabs are broken or sprung. A new tower isn't very expensive. You can probably get one from SearsPartsDirect.com, Repair ... Kenmore Dishwashers

My siemens dishwasher bottom arm does not spin to clean the bottom basket of dishes. Everytthing else works fine. I have removed and cleaned out all washing arms and plastic water carrier inside machine. Any ideas please?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Siemens 24 in. SE64A630GB Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1082 seconds