Having problems with your Kenmore 15762 Dishwasher ?

When I choose a cycle on the actuator dial and then close the door the water supply does not begin. How do I fix this?


Answers :

Http://www.servicematters.com/maytag_library/docs/16010622.pdf\015\012\015\012\015\012
\015\012Above is your service manual. \015\012
\015\012Below is a DIY troubleshooting site to help you along with your service manual to isolate and troubleshoot your issue.\015\012
\015\012http://www.acmehowto.com/howto/appliance/dishwasher/dishwasher.php\015\012
\015\012When this happens usually it is either a sensor, or the Controller board that has been spiked. or the water may not be coming in, because the Inlet Valve may be stuck. You MUST perform the troubleshooting steps, to sort it out.
Repair Help & Product Troubleshooting for Kenmore 15762 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I choose a cycle on the actuator dial and then close the door the water supply does not begin. How do I fix this?


Http://www.servicematters.com/maytag_library/docs/16010622.pdf\015\012\015\012\015\012\015\012Above is your service manual. \015\012 ... Kenmore 15762 Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Whirlpool dishwasher model DUB700XB has quit cycling. Fills with water but will not start wash cycle. Making intermittent humming noise unless the door is open to disengage the switch, even when on stop. No LEDs lighting when rotating the dial through the various cycles. Unit is old and wondering if it's better to buy a new one rather than fix this and have something else go wrong in the not to distant future. Thanks in advance


... Dishwashers

After installing the new Kenmore model 665.13293k I tried to run a short cycle. Nothing happened and the selector lights timed out. Checked water supply and filter screen - OK. Panel lights so power is on. I don't hear any sound from the electronic water valve when door is first closed.


... Dishwashers

Free standing hobart model KDD 60A Serial # 222601715 Washer does not start when door is closed and locked. Electrical power to wall socked operating. Machine plugged in. Water supply connected. Start attempted in rinse cycle and wash cycle.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or door\015\012lock switch which is not engaging its ... Hobart Dishwashers

Machine cannot finish cycle and is stuck in pumping out mode. Only tiny amount of water in drain basin at bottom, no excessive water. Was set at 10pm, still attempting to drain 8am! Has no diagnostic dials or manual over rides so continues on whether door is open or closed, even if I switch off and on again. Possible related issue, recently finish at end of washes has been "grainy", far from perfect, surfaces slightly sandy feeling.


... Bosch 24 in. SGV43A03 Built-In Dishwasher

Hello, my Siemens integrated dishwasher no: SE64M359GB stopped working mid-cycle with 35mins remaining. It is displaying the red tap emblem. Usually the dishwasher starts when the dishwasher door is closed fully (having pressed the power button). However, it is making a noise as soon as the power button is pressed. I have checked the water supply and pipes and they are OK. The filters are also clean and OK. We have an electric de-scaler on our system so I imagine calcium build up should n


... Siemens Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My Brandt VF300 dishwasher is not draining properly. If I empty the residual water (by hand) I can still use it but the water still remains in the bottom at the end of each cycle. How can I fix this? It's driving me nuts! Also the door is not functioning properly something has broken that supports the weight of the door. It can only be shut completely or open completely! Is there a part that can be bought to fix this?


... Dishwashers

We removed the dishwaser 3 months ago for renovations. It has been reinstalled (everything looks ok). However, app. 2 min. into the cycle the door pops open. Eventually the cycle completes but only by pressing the door closed and hitting restart button 2 or 3 times per cycle. With the constant door popping there is considerable condensation on the new cabintry. What can we look for to fix this proble. thank you.


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

Water will not drain out. do not have a drain airGap. when opened dishwasher this afternoon still had water in the bottom of it. Emptied the dishes, closed the door, pushed cancel/drain. the green light came on and i could hear the dishwasher running but not hear the water draining out. Let it run the 2 minute cycle for cancel/drain opened the door and the water is still there.


Hi,Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain out ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1748 seconds