Having problems with your Kenmore 15899 Built-in Dishwasher ?

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


Answers :

You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part
Repair Help & Product Troubleshooting for Kenmore 15899 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

PROBLEM: Unit will start, fill with water, wait through normal cycle time, then drain. Unit does not perform washing (arms spinning & spraying water, etc.) cycle.


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012is that the control detects that the motor is not running and so drains water\015\012directly after filling it. If you hear a hum sound from the bottom p ... Frigidaire Dishwashers

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

I am having issues with my dishwasher where it appears to be working but does not clean. Hot water does enter the unit and drains properly but is not cleaning. Muck is still on the door, the arms are wet. Also, normal cycle with no extra features selected (i.e. High Heat, etc.) takes over 1 hour and 20 minutes. Sounds appear to be normal, draining, filling, etc. Thanks!


No\015\012 you need not wash the dishes but just cleaning of the debris and then \015\012putting it in the dishwasher for proper cleaning will help you to \015\012prevent the drain from getting blocked.\015\012\015\012 ... Dishwashers

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


... Dishwashers

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

Upper spray arm is not turning round even though water is coming through. We have checked the internal system for blockages and the machine is filling / draining as normal. When a full programme is run, many of the dishes, particularly on the top shelf, are dirty and many have hardly been touched by water. Could a pump or other part be faulty?


I found the problem to be neither blockages of the upper arm or roof spray arm or the upper basket arm hitting the the back of the dishwasher. the problem was that the pump inlet where the food scraps are macerated was blocked with all manner of gung ... Dishwashers

I have a Quiet Guard Standard model #587.151524 that is not cleaning the dishes. I took the bottom spray arm and screens out and cleaned them, (they had a heavy buildup of what I would say is calcium. The arm cleaned up fine but the screen still has some areas that will not allow the water to drain. I tried CLR and it helped but the screen is still probably 60% clogged. Do you think this is the problem getting the dishes clean and if so do you have any suggestions about how to clean the screen?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Kenmore 24 in. 15689 Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Kenmore dishwasher model 665.16033401 doesn't drain well. Drain pump comes on but drain water only trickels out slowly. Obstruction somewhere ? Removed rotating spray arm inside to try & get at the place where the drain water enters pump. Can't remove any parts beyond spray arm. Home: 330-865-4813 Cell: 330-608-3022


... Dishwashers

Dishwasher pump will drain but not force water into spray arms


If the washer is not used regularly the shaft can stick to the seals and prevent the motor from spinning. This happens quite regularly for me if I don't use the washer often. You can just take off the bottom panel - after shutting off power to the ... Hotpoint 18 in. DC27 Slim-Line Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have an older bosche dishwasher and the I know the water is flowing into the unit and collecting at the bottom of the drain but it is not getting into the spray arms in the middle and top to work at all. Any help would be appreciated.. Thanks


There is a chacne that the main wash motor is not drawing enough water into the pump to spray through the arms.you can try and add some more water to the dishwasher and see if there is any change.\012if there is no change then you migh need to ... Dishwashers

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

Kudt03ftss3 upper spray arm isn't getting any water, middle spray arm has water coming out but isn't turning, lower spray arm moves but slower than normal.


... KitchenAid Dishwashers

Hi, my hotpoint aquarius df61 makes all the noises of washing, i hear the water going in, motor is running, however i dont believe the spray arms are revolving, so the dishes are not getting clean. i have cleaned the individual holes in the spray arms, but i don't think the water is getting up the back pipe and into the top spray arm. it does not spin at all. no problems draining. help please. and were can i get a copy of the user guide, free preferably. thanks


How old is your machine? it is posible to have something in the watwr pump, you hear the water and the motor, but the fan of the pump (washing pump) is blocket. also the pipes hat make connection to the water pump and the arms. at someoane i found gl ... Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1478 seconds