Having problems with your Kenmore 16024 Built-in Dishwasher ?

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Answers :

Hi,

This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Kenmore 16024 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Hi,This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.Let me kno ... Kenmore 16024 Built-in Dishwasher

My DW was running fine, the next time I tried to use it, it just didnt work. We have made sure we have power, we have taken off the front panel, but don't see any thing loose or unusual, but niether do we see a re-set button. We are at a loss? Please help. (Don't understand about the thermal)


First what do you mean when it wont work,,it dont turn on,,,the water is not coming in ,,,please advise with more info ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

DU943PWKSO DISHWASHER STOPPED WORKING, ELECTRICAL CURRENT TO PANEL BUT DOES NOT START NOR DOES ANYTHING TURN ON. LAST YEAR HAD THE SAME PROBLEM TECH TOOK FRONT APPART AND THE DISHWASHER STARTED WORKING. I ATTEMPTED TO DO SAME BY CHECKING CONNECTIONS BUT NOT WORKING. COULD IT BE THE CIRCUIT PANEL?


Check you electrical power box that feeds to the house. If this dishwasher is hooked up under a sink counter and there is a garbage disposal in the sink area the dishwasher should be hooked up to the same circuit that the dishwasher is hooked to. If ... Whirlpool DU943PWK - Multiple Color Built-in Dishwasher

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

My Kitchenaid dishwasher Model KUDPO1FLSS3 stopped working. The electrical works, as we checked the breaker and the little lights on the panel turn on, but the machine will not start. We're thinking there might be a problem with the connection where the door closes. We've checked out everything we can think of, but no luck. The plastic panel is worn away in places, so some of the buttons are exposed-can't imagine that matters, though. Help!


... KitchenAid Dishwashers

I'm attempting to reuse a Maytag dishwasher motor for a bench grinder. Since this is a reversible motor, I'm not sure how to connect the wiring to a simple switch so that it works in one direction only. The motor has 4 wires: blue, gray, red, yellow. Not sure which to connect to the hot (black), return (white) and ground (bare) wires from the romex and can't find a wiring diagram online for this dishwasher. Any ideas? Thanks.


... Hobart 29 in. AM15-1 Free-Standing Dishwasher

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

Hotpoint dishwasher I need to change waste pipe on my hotpoint dishwasher. I was given this dishwasher by a friend and it works well but I cant connect the waste pipe to the bit under the sink as the rubber connection on the end is missing. I bought a new waste pipe but not sure how to connect


Did you have a dishwasher before? If so, you must have had a sink tail piece with a dishwasher drain coming off the side. For the connection, you may have to get an adapter to fit the end of the dishwasher drain hose to the sink tail piece. Take a ... Dishwashers

Greetings! My Bosch SHE3305UC/UC12 has worked faithfully until last week when we had to pull it out of its home to retile the floor. Upon reconnecting all of the connections, it no longer works properly. The initial drain cycle works, so the flood switch is fine. But after draining, it just quietly hums. The test cycle actually seems to move to the next step for about 30 seconds, before also just humming. I'm thinking I need to check the valve, but not sure how to do it on this mod


Hi\015\012\015\012The hum sound indicates a bad motor and it should be\015\012replaced. Hope this helps...please post back for further assistance.\015\012\015\012Daniel ... Dishwashers

DD602I USA v2. Runs approximately 10 min then beeps continuously and on the front panel the middle light is red and on the inside panel the "Del" "Fast" and "Rinse" lights are red. What is this fault code indicating? I have made sure spray arm, impeller assembly, are clean and not blocked. No kinks in drain line. Induction motor sounds a bit noisy. This is only a problem with lower drawer, top drawer works fine. Thanks, Keith


... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have a Kenmore elite 13102 dishwasher touchpad that has begun to crack around the start button. Does this necessitate changing out the whole electronic control pad or is there a part that is the "overlay" to the control panel? The functions for each button on the panel work fine. LH


Hello,You will need to replace the touch pad assembly. You can purchase the part from the link below. ... Dishwashers

Model GLD6500L00BB Dishwasher was beeping after the cycle started. I opened it up and reclosed it to make sure it was latched tightly. That did not work. I then unplugged it and plugged it back in and now it won't work at all. The panel does not light up or anything. Any suggestions on what is wrong? Thanks!


... GE Dishwashers

My 2 year old dishwashers control panel does not lite up to allow any functions to work. We had been giggling it to make it work but that does not. I checked the power connect etc and all seems fine.


... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

Frigidaire Dishwasher won't start (lights cycle but no water/motor) Model Number: FDB1050REB2 Brand: Frigidaire Our dishwasher is 1.25 years old and already not working (grrr!). When it is turned on, the lights cycle through like a normal wash cycle, but the motor isn't engaged nor does any water cycle through. This happened about a month ago and I took everything apart to make sure all of the connections were secure and it started working again...not this time. Any ideas?


... Frigidaire Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

I have a GE dishwasher with the following model number: GSD3230F00WW. Last night, while the dishwasher was in the clean cycle, a buzzing/grinding sound came from underneath the dishwasher. I removed the access panel to try to isolate the sound. It appeared to come from a solenoid that was connected to an arm that opened and closed something. I am not sure if the solenoid is bad or if there was something that was preventing it from operating properly. I moved the arm to which it was connected


The part you are referring to is the pump out solenoid. ( part # WD21X10071) When the dishwasher is suppose to pump out, power is applied to the solenoid and it swings a flap inside the pump assembly to divert the pumped water out the ... GE Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

My Frigidaire dishwasher will not start. It was working fine about a month ago. The lights on the panel are working and I had the water line checked and it is o.k. I cannot find a serial number but the book that came with it is for the 500, 1100, 1400 & 1500 series with fully electronic control.


My Frigidaire 500, 1100, 1400, 1500 & 2400 Series Dishwasher was purchased a month ago and it will not start either. The 8 second lock under "Heat Dry" is lit, but nothing happens when you press any of the other buttons. Any ideas? ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0848 seconds