Having problems with your Kenmore 16522 Built-in Dishwasher ?
The miser cycle is running about 1 1/2 hours! This is too long!
Is the timer broken? This includes only the wash and rinse cycle,
without elec dryer!!
Repair Help & Product Troubleshooting for Kenmore 16522 Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The miser cycle is running about 1 1/2 hours! This is too long! Is the timer broken? This includes only the wash and rinse cycle, without elec dryer!!
... Kenmore 16522 Built-in Dishwasher
During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.
I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher
Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or
I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher
Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.
This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher
Hobart lx18 no power to detergent pump, during the wash cycle there is no power present at the connections for the pump, during the rinse cycle the sanitizer terminal will pulse power and the rinse aid and sanitizer pumps will run, is the relay board bad? With the top drawer open and running the led for detergent never lights up during the wash cycle.
You have to go into program and activate the detergent pump.sounds like somebody deativated the det. program ... Hobart 24 in. LXIC-5 Built-in Dishwasher
I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one
... Ariston Technologies Dishwashers
I have a ADG 450 dishwasher, it has suddenlt topped completing the wash cycle. it runs for about an hour then sits and beeps. If i open the door, the machine is full of water and it looks as though it is trying to spray more water in, thn stops and beeps. If i turn it off and on at this stage and run the rinse cycle, the water clears and the dishes appear to have been cleaned. any thoughts? it happens with all wash cycles.
... Whirlpool Dishwashers
Excessive foaming when using Rinse Only Cycle in Kitchenaid Dishwasher. I've had this dishwasher only 3 weeks. There is no detergent in the dispenser. Rinse Cycle should be only water; no soap. Rinse Aid should not be dispensing either. What could be the problem? Normal wash cycle leaves residue on glassware. That is why I run the Rinse Only Cycle. I have done this over and over with the same results? HELP!!!
Do you have a softner in the house ... GE 15" Laundry Pedestal for Horizontal Axis Washers and Dryers - White-on-White
My Defy Dishmaid Silent makes a loud knocking noise when i start the wash cycle, it fills with water but dose not wash.When i start the wash cycle it sounds like it is washing with the added knocking noise but at the end of the cycle the salt has been released but nothing has been washed.A few weeks ago it would run the rinse cycle but now it will not wash on any of the cycles.Please advise.
My GE dishwasher drains fine after wash cycles. However, After rinsing, about 2 inches of water is left in the tub. The drain runs for 30-35 seconds at the end of each wash cycle, but only 4-5 seconds after the rinse. What do I need to do to fix this?
Many dishwashers use a drain valve with an electric solenoid. When electricity flows to the solenoid, the valve opens and diverts the water to the drain. Sometimes the solenoid, or the diverting lever, sticks and prevents the dishwasher from dr ... Dishwashers
Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button
The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers
Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???
Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers
The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles
Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher
DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.
... Smeg 24 in. DWI612 Built-in Dishwasher
Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella
Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher
I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.
... GE Dishwashers
I have a Kenmore diswasher model 587 1525. I can hear the water filling and rinsing, but during the wash cycle I do not hear the motor. At the end of the wash cycle and when I open the door I see the detergent tablet is sitting on the floor. The dishes are not cleaned. Does this mean that the motor has failed or is it the control card. I can hear some clicking noise while the motor should be running. Maybe solenoids cycling.
... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher
Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w
Most common d/w power is 120 volts, check for 120 volts with a ... Dishwashers
The washer won't complete it's cycle. It just runs and runs. One time I got it to complete by turning it off, then switching to the Rinse and Hold cycle, but now nothing works. It doesn't drain the water, it appears to be stuck in the wash part of the cycle.
... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher
I have an equator PLS600 and I can't seem to get it to work. I have tried the WikiFix to help a stalled dishwasher, by adding water and vinegar. When I put on the wash cycle it does not run. Even with the short rinse cycle, the sprayer will not move, and the machine will just run through the cycle until it starts to drain. Please help!!! Thanks =)
Give the spray arm a spin to make sure it rotates. It should spin freely. If not, remove plastic spray arm clip, flip it over, replace it, and try again. Make sure holes in the spray arm are clear of debris. Spray arm must be clean for it to spin ... Equator 20 in. PLS600 Free-Standing Dishwasher
I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?
It is stuck on nine minutes rinse only cycle i will start it at normal wash (2 hrs) and it reverts back to the 9 minute rinse only.. When it is running I cannot cancel the cycle
Hi mlbierman, I have the exact same problem (The 9 minute rinse). Have you been able to resolve it? Will appreciate help. My email is sanjeevnutsATyahooDOTcom ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher
When I started it, it made a loud grinding sound which continued whenever it was actually washing/rinsing. It was washing and rinsing the dishes ok. Eventually I didn't hear anymore grinding but the dishes had not been washed or rinsed. The detergent cup was open and the detergent spilled down the door. I ran it again and could hear the pump running. It ran through the cycles but the water was not being circulated. I suspect that something is caught in the disposer blade or something and is bloc
What is the brand and model number. it likely will have to be disassembled to clean it out. is it a built in dishwasher or a stand alone type ? ... Dishwashers
Our Maytag dishwasher has all of the sudden stopped rinsing the dishes. The machine sounds like it is running but no water is flowing. The wash cycle runs but not the rinse. Any clues as to why
Check inlet water supply for free flow. check strainer for blockage. Strainer is located at the machine body water inlet tube entry side. ... Dishwashers
When using my Omega DW2006 dishwasher, the machine always displays that it has completed the wash cycle, when it has only done the pre rinse (after approx 12 minutes). Despite following the operating instructions religiously, I can't get it to run a proper wash cycle.
Hi,\015\012\015\012It seems that Motor pump has gone out. You need to replace the pump. In order to do this the unit needs to be pulled out so that you can access the pump. The sides of the dishwasher come off. \015\012Replace ... Dishwashers