Having problems with your Kenmore 16602 / 16604 / 16609 Built-in Dishwasher ?

Control panel access

\015 How do I access the control panel to get to the thermal fuse Kenmore ulta wash quiet guard\015

Answers :

Open the door and remove the top screws connected to the console. Close the door and flip the console down toward you. Remove the control cover to gain access to the control board and the thermal fuse.
Repair Help & Product Troubleshooting for Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

I have a Kenmore Elite dishwasher with electronic controls. When I set the controls press the start pad and close the door it will not start. The light on the start pad just continues to blink. This happened about six months ago and the Sears serviceman pressed two of the control pads simultaneously and this reset the controls. Everything worked after he did this. What are the two control pads that you press to reset the controls?


This is difficult to find out. Try different combinations. Otherwise get the information from the SEARS serviceman. ... Dishwashers

The Hom Model No. 308653045 gas-operated cold-water pressure washer has a spring-loaded control on it and I am assuming that this control regulates the output pressure of the water from the pump . . . for example, 1500 psi to 2700 psi. Is it correct to assume that this control regulates the output pressure of the pump. If the control is a pressure regulator, how does one use it and, EVEN MORE IMPORTANT, can one under-adjust or over-adjust the control to a point where THE CONTROL OR THE PUM


... Homelite Pressure Washers

I have a Maytag dishwasher MDBM601AWW. The control lock on the control pad will not unlock. I replaced the electronic control board and it worked for one wash. Control lock engaged again. I shut down the power and pressed the control lock for 3 seconds as directed by the owners manual. No luck. Please help Rich.


You have to power the unit back up and then holld the lock in for three seconds, if ths does not reset it then the console not the control bord needs to be replaced it comes with a new touch pad ... Dishwashers

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

My Kenmore refrigerator ice maker does not make ice. The control module motor (W10190935 ICEMAKER CONTROL MODULE) runs continually. Is the control Module bad or is there a sensor that controls its ope


Check the compressor of your refrigerator first. If this does not work out, then visit Ice Machine Cleaner. ... Whirlpool W10190935 WHIRLPOOL W10190935 ICEMAKER CONTROL MODULE AND MOTOR A

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Leak from a De Dietrich Integrated Dishwasher has caused 3 red lights on the left of the Control Panel to flash and also a Blue Light on the right hand side of the Control Panel to flash. On resetting the Appliance Controls, the machine starts pumping out and then closes down, with the Control Panel lights flashing again. Help


Pull the built in unit out and tilt towards the rear right leg and the water will drain on to the floor. The Dishwasher then restarts but the anti flood sensor will reactivate after 2-3 more washes. Do not know final fix yet. ... De Dietrich Dishwashers

I cannot unlock the controls on the panel - i just bought a house that has the whirlpool gold quiet partner dishwasher and when i press any button nothing happens but says controls locked - i unlock the controls and try to turn on the dishwasher and still happens and says controls locked again. can you help?


Try turning the circuit breaker off for 30 minutes. Then turn back on and see. If it keeps locking you may need new control console. Hope this helps. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I purchased a whirlpool dishwasher GU2475xtvy2 with interior controls on top of the door. Might seem like a silly question, however, do I have to install with the door & controls controls out from under the countertop? or do I install with controls hidden, and make selections before closing door? Doesn't address this in the installation manual. Thanks


Hi,It is up to you as to where you fasten the dishwasher at...if you push it back too far then you will have to do the setting before you close it which is no problem... but if you want it out a bit then you can do that and you will have a hip ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

MDB6709AWW1 Poor Quality Control Panel Our dish washer is 2 years old this month and the control panel broke!!! My service technician told me that he has seen DOZENS of new Maytag dishwasher control service panels break and is convinced it is a design flaw. When I called Maytag the customer service rep had the NERVE to tell me "that because the house is near the beach, I must get a lot of power outages and power surges, that is why the control panel broke." I told her I wasn't born yesterday


... Maytag Dishwashers

The start button on KitchenAid model #kudp01flbl6 will not engage, although all of the other lights in the control panel light when pressed. The cancel button will turn off the other lights in the control panel as well. This diswasher is 5 yeras old and lightly used in a household of just 2 professional adults. I've had service come and he uncovered a "burned' conection in the electronic control assembly p/n 8564542, which looked to me to be P8. A new electronic control panel was installed


HI. I need you to clarify somethign for me. You mentioned that you have replaced the " electronic control panel". Are you reffering to the interface board or the actual plastci panel? I understand that the part number "8564542" in in reference to the ... Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

The control lock light goes on as soon as I press the cycle to start the dishwasher. The dishwasher does not start, presumably because the control lock stays on. I do not know how to disable the control lock function. Pushing and holding the button for 3 seconds does not disable it.


Hello &\015\012Welcome to FixYa\015\012\015\012To unlock the\015\012controls press and hold the HEATED DRY button for 20seconds. If the problme\015\012returns then only option is touch pad replacement. Please get back t ... Maytag Dishwasher

My serial #TH24050632 has an occational control board failure and requires a reset. That is my current problem. In the past I turned of the circuit breaker for thirty minutes, and then pressed sertain control buttons inseries or at the same time for ten to twenty seconds. I have misplaced the information I wrote down to correct my problem. Can you help me with the correct procedure to reset my control panel? Thank you.


Check if this works.\015\012\015\012Press normal wash and heated dry one after the other about 5 times.All lights on panel will light.Wait until all lights go out and it resets itself.It will go into a mode on it's own.Then press cancel a ... Dishwashers

Kenmore Elite Dishwasher- The touchpad (control panel) keeps going ot and stops functioning. The control board is fine but the start button on the touchpad stops working. If I press it multiple times over and over it will finally engage and kick on. This is my second control panel, can the switch membranes be cleaned somehow?


Jodahabo,\015\012\015\012can you post the rest sequence? i would love to try this!\015\012\015\012thanks,\015\012\015\012the_strum_one ... Dishwashers

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

I have a maytag performa dishwasher. It will not turn on. The pushbutton control lights just flicker. Would this be a problem with the pushbutton control or the control circuit board?


... Maytag Dishwashers

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0507 seconds