Having problems with your Kenmore 16602 / 16604 / 16609 Built-in Dishwasher ?

I have done the normal wash heated dry method and

\015 I have done the normal wash heated dry method and it does work for a while --but the cycle seems to take too long and it keeps washing and sensing etc.--then the green lite starts blinking again-- so I do the NW HD thing again and it works for a while. I will say my wife put some candle holders in the dishwasher with some wax in them-- is it possible a sensor is messed up?\015

Answers :

This would mean there is a failure in the unit most likely of the heating element, if the water does not heat the light will blink
Repair Help & Product Troubleshooting for Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have done the normal wash heated dry method and


This would mean there is a failure in the unit most likely of the heating element, if the water does not heat the light will blink ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Kenmore Ultra Wash Quiet Guard 4 Dishwasher model 665160344000 normal wash light keeps flashing. I have done all of the push this button and that button combinations I can find on the internet. I unplugged and repluged the 14 pin ribbon with power and without power --no joy. Looks like I need a new part - which part?


Hi\015\012\015\012Open the door. Within 3 seconds press the following sequence\015\012--Try pressing normal wash, heated dry, normal wash, heated dry, normal wash,\015\012heated dry three times within 6 seconds and then press cancel to re ... Dishwashers

I have whirlpool du912pfgbo and the problem is that the secondary soap door will not open when the normal wash cycle start,so when the washing is done the soap is still in there.


... Whirlpool DU912 Dishwasher

Excessive foaming when using Rinse Only Cycle in Kitchenaid Dishwasher. I've had this dishwasher only 3 weeks. There is no detergent in the dispenser. Rinse Cycle should be only water; no soap. Rinse Aid should not be dispensing either. What could be the problem? Normal wash cycle leaves residue on glassware. That is why I run the Rinse Only Cycle. I have done this over and over with the same results? HELP!!!


Do you have a softner in the house ... GE 15" Laundry Pedestal for Horizontal Axis Washers and Dryers - White-on-White

We have a Frigidaire Gallery Series dishwasher we just purchased in August. Model #GLD2445RFB2. We are experiencing a problem with it. We noticed it started running louder then normal and now it will not finish a wash cycle. It gets half way through and PF lights up on the display and the cycle never finishes. It doesn't matter which cycle we choose it has done it on all of them.


... Frigidaire Dishwashers

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Roper dishwasher washes, seems to run normally, but leaves a couple inches of water in the bottom when done


If the drain is stoped this will happen. Is it a new instalation? If into a disposer did you knock out the plug in the disposer. Check the drain line ... Roper 24 in. RUD4000M Built-in Dishwasher

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

NORMAL Wash light is blinking and I can't CANCEL wash. GE Quiet Power II PROFILE dishwasher. Started a normal wash and a few minutes into it the NORMAL light started blinking and can't find a way to reset.


We had the same issue with ours...tried turning off at the breaker, still didn't reset. Contacted appliance repair who came in and unplugged it from underneath the sink, waited a few seconds and plugged it back...dishwasher reset and repairman charg ... GE Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Model #665.1746 The Smart Wash and Normal Wash buttons are blinking, and neither wash cycles begin when the Start button is pressed. The Cancel button drains and sometimes turns off the Normal Wash button from flashing, but it seems no matter what I do the Start button does not start any of the wash cycles.


... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

The machine fills ,drains and washes as normal. However when it fills the wash temp is 60 as normal but the rinse temp wont go higher than 76 deg C . when the wash cycle is on , the cycle stays on wash not progressing thru drain and rinse What is the cause?


Hello. Let me assist you. There are only two reasons for your problem - if you can isolate your problem based upon these descriptors you will know which part to replace:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-he ... Dishwashers

Dishwasher lights up when Normal Wash is pushed, also heat dry - but when start is pushed all three lights (Normal wash, heat dry and washing) blink then go out and nothing happens. This occurred after a 2 hour delay was attempted last night and no washing ever happened.


What is the make and model so we can better assist you? In the mean time shut power off to the unit briefly, then turn it back on and try a normal cycle. Will be watching for a make and model here. ... Dishwashers

KUDS30IXSS1 dishwasher will pump out water completely on the one hour wash cycle, leaves water in tank at end of all other cycles. Will completely drain when cancel/drain cycle is pushed. Is there a re-set code, or sequence; or is there a diagnostic code or sequence tohelp me? Like push Heat/dry, then normal wash, then Heat/dry, then normal wash within 6 or 7 secs? Or is my circuit board just shot?


... Dishwashers

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Indesit idl 535, washing on usual cycle but not heating and dishes not being cleand properly? Disolves tablet and goes through full wash cycle as usual but doesnt wash dishes properly and the dryer isn't working as it normally is hot when you open the door, but it is just cold. water draining as normal too.


Your problem is very clear, you need to replace the wash tank heating element. ... Indesit 24 in. IDL500 Built-In Dishwasher

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.


Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1062 seconds