Having problems with your Kenmore 16602 / 16604 / 16609 Built-in Dishwasher ?

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


Answers :

Repair Help & Product Troubleshooting for Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Dishwasher won't run. Normal wash blinks. We tried pushing normal wash and heated dry and repeated that. Didn't work. Also tried high temp then heated dry twice. That didn't work. Any other options to try???


... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Kenmore Ultra Wash Model 665.1388 problem the normal wash green light is on heated dry light is on and the start resume light is flashing but wont startup helpppp


... Kenmore Dishwashers

Kenmore Ultra Wash Model 665.1388 problem the normal wash green light is on heated dry light is on and the start resume light is flashing but wont startup helpppp


See your instruction manual and go to the section troubleshooting and fix it.if you do not have the i.manual download for free www.retrevo.com or www.fitness.manualsonline.comsee the diagramGod bless you ... Kenmore Dishwashers

Sometimes I can run the dishwasher with no problems. Sometimes i will run it and leave the house and come back 5/6 hours later and it is still running on the wash cycle but it is only putting out heat and no water. So its drying up the soap on the dishes and not really washing anything, and it get stuck on that cycle


... Magic Chef 24 in. DU4500 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Dishwasher runs full cycle, however, the dishes and glasses have small particles of food dried on them when done. I do rinse all plates and utensils before turning on. I run on a normal cycle, no heat dry. I use cascade action paccs 4X concentrate. Which appears to not disolve completey, the packet. It normally does. There is no water back-up in sink, and I also open the trap ,no blockage. Please help, Dan


Hi Dan and welcome to FixYa, I am Kelly \015\012\015\012 Most of the time when you start having dirty dishes post wash there is either an internal blocked screen under the lower wash arm tower or a problem with the drain. ... Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1315 seconds