Having problems with your Kenmore 16602 / 16604 / 16609 Built-in Dishwasher ?

My kenmore dishwasher isnt changing cycles just washing over n over. model# 587.15173400 put new heat sensor but still not changing


Answers :

Repair Help & Product Troubleshooting for Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kenmore dishwasher isnt changing cycles just washing over n over. model# 587.15173400 put new heat sensor but still not changing


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a whirlpool dish washer model#du1100xtpq3 type 575-0 it has a green lite under sanitizer that flashes seven times and won't let it start i have been told by ask a repairman payed 28.00 told me it was a heat element 30.00 installed didn't change was told it was a door switch amother 32.00 installed still no change any ideals?


Seven flashes indicates an F7 fault code!\015\012\015\012 ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

I have a hobart LX18C. I purchased a new control board and as I found out its factory set to the h model. How do I change the board over to the c model. How do I program the machine for the different wash cycle times, I have one that is working but its on the 140s. cycle and only heats the water to 80 degrees. I see the push buttons on the control and wonder what they are for.


Here is a Hobart link that may help. https://feg.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Have kenmore model # 665.16773402 serial # FT0302854 display flashing 7 times have reset twice and did not good checked the heating element seems to be ok should I change the sensor next


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water temper ... Dishwashers

I have a brand new Whirlpool dishwasher #DU810SWPU4 - Model #. No instruction manual was left with me, so I want to be sure I'm using it correctly. When I run it and set the drying cycle to Heat - after it shuts off and I open it up, there is still water on the door and on some of the dishes. Is this correct? Jane Walker


... Whirlpool Dishwashers

The slide on the upper basket keeps falling out. It's been fixed twice but doesn't hold. The second repair man who put the slide back in the rollers said he couldn't see anything wrong with it, but it still didn't hold, so he called your tech dept. who said they had roller and slide kits at a total cost of $66 for this model. The slide kit had a new part number but the tech department didn't tell the repair man why they'd changed the part. The roller kit was one for dishwashers the sides o


One option is installing stainless steel washers on the rack supports that screw into the side of the tub. The rack falls down because there is too much "slop" with the rack...a couple small washers to space them tighter normally does the trick. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

I am an electrician, and have been called to repair a faulty Hobart comercial dishwasher. I didn't note the model number, but it is the same shape as the one pictured. The problem is that nothing happens when the lid is closed, like it has a faulty switch or sensor. When I got to site, the dishwasher had been drained, and would not automatically refill. I filled it with a bucket, it heated the water to the correct temp, but still nothing happens when the top is closed, and I have to have it


Hello Pat. Here is the link to the hobart line of kitchen equipment. It has all of their manuals as free downloads. If you have a laptop and internet access you can get the correct manual once you know the model number. Based upon what you said t ... Hobart AM15-5 Dishwasher

I have a power washer, craftsman &.0 horsepower, 2900 psi, 2.3 GPM model number 580.752410. i was starter to wash my car, and stops? i change the spark plug, andput new oil in there. still do not working. some one helme in this problem.


... Craftsman 3000 PSI 27 GPM Briggs Stratton Powered Pressure Washer

11 hp honda pressure washer engine won't start. No spark at the pkug, bought a new coil and still no spark. This sysem only has a coil off the fly wheel and the spark plug. I even changed spark plug. Use the unit the other day, shut it down and on restart it won't start. Also, I disconnected the kill switch and the il lvel sensor so nothing was going to ground.


If you replaced the coil,check the wire and boot,check with meter for continuity.could be loose connection to spark plug ... Honda Pressure Washer PSI 3000

Hi, my Ge profile dishwasher model pdw9280n00ss changes wash modes on it's own. This is a new problem, it was stuck on normal wash for the last year. It screwed up right after the warranty ran out. The start button and the heat all seem to work. I've seen it jump between the wash cycles on it's own while washing . Is it worth fixing, I feel ripped off on this expensive dishwasher!! Thx


... GE PDW9280NSS Built-in Dishwasher

I have a GE Monagram dishwasher 1999 /- model ZBD 5900/5700 It is stuck on Heated Dry cycle. Would not drain for along time, than it finally drained but still stuck on Heated Dry. Turned breaker off and on several times did not help. Still stuck on Heated Dry no other buttons work


... Dishwashers

Hello, Firstly, thank you for what you do, you help so many people and I know it takes time. I have a Bosch SHE44C06-UC Dishwasher. I fixed the E1 (Heating Circuit) error. First, before I found the writeup about the solder joint, I bougut a new heater and replaced it, ithe part included the element, flow switch and high temp sesor soall are new, then I fixed the solder and E1 went away and the cycle finsihes and the dishes are clean and dry. Still I check the error codes and still have


... Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

DOOR REPLACEMENT I have a GE-Triton XL dishwasher model GSD6600G00WW in white that is only about 4 years old and I'm now redoing my kitchen and want to change to Stainless steel. Can the door of my dishwasher be changed to a new door instead of buying a completely new dishwasher?


On most dishwashers the front panel is removable/replaceable. You can try www.coastparts.com or www.marcone.com ... GE 24 in. GSD6660GSS Built-in Dishwasher

Terex tr60 rigit truck locks in range with load.recieved output speed sensor code,changed spd sensor problem still exists would appreciate any sugestions


... Dishwashers

I have a frigidaire dishwasher model # PLD2850RDC0, it will not change cycles from the lower rack wash cycle. It will not turn off or change to any other cycle. When I take power from it and reconnect it will let me change cycles at first, a sensor light on the control panel lights then it changes to the lower rack cycle by itself and we repeat it all over again.


... Frigidaire Dishwashers

Troy Bilt 2550 model 020337...put a new spark plug in and it still won't start. Set choke and still nothing....what's next?


See if it fires with starting fluid if so clean the carb out ... Pressure Washers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Westinghouse Dishwasher Model SB907W5*08 the dishes are not getting cleaned & it appears that it is not heating as i bought a bottle of dishwasher cleaner & the dishwasher is supposed to heat up enough to dissolve the lid off the cleaner to let the fluid out. after putting the cleaner through a cycle the cleaner lid was still there. i think this must mean that the heating element is broken? this is out of warranty & can't remember how much it cost us so don't know whether better off gettin


Hi\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's spray arms are w ... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher

Dryer tumbles but does not heat. We replaced the heating element, thermal fuse and the circuit breakers are okay.. why is it still not heating. Is it the controller? The dryer is a Kenmore and the model number is 96374200.


Is the blower working and is lint chute cleaned out in the back of dryer? ... Dishwashers

The heating element stopped heating in my Maytag dishwasher, Model DWU8860BAE. I put in a new heating element, but it doesn't heat.rnWhat might be the problem? What should I do?


... Maytag Dishwashers

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1371 seconds