Having problems with your Kenmore 16602 / 16604 / 16609 Built-in Dishwasher ?

How do I remove an Ultra Flow water feed tube from a 665.1386 dishwasher


Answers :

Repair Help & Product Troubleshooting for Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove an Ultra Flow water feed tube from a 665.1386 dishwasher


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

I have a Kenmore Ultra Wash Dishwasher model 665.16379301. The spinner from the top of the dishwasher has come off. I have a replacement part but need to know what is required to replace it. Do I need to remove the feed tube assembly in order to replace it?


... Kenmore Dishwashers

Replacing the ultra flow water feed tube - Kenmore 665


... Kenmore 665

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers

I have a Whirlpool GU2500XTPQ3 dishwasher that is about 5 years old. The dishes in the top basket do not get clean. I checked the water tube that feeds the upper spray arm and the top spray and there aren't any obstructions. Our water pressure and temperature are suitable. Could the pump be plugged or otherwise lose its ability to circulate enough water to adequately feed the upper sprayers? How can I check on that?


Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012Based on your description as well as all you`ve done on your own I`d suspect you`re on the right track with the plugged pump suspicion.\015\012\015\012The plac ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Dishwasher problem dishwasher begins to wash, water flows in, then both first and second green indicator lights flash together and the cycle does not complete. I have cleaned the filters, removed water that's left in the bottom of the dishwasher.


My dishwasher Indesit DI67S will not run on the number 1 cycle. It will fill and then when that programme finishes it jumps straight to the drying cycle missing all the rinses out etc. If on the number 2 programme it goes all the way through but then ... Indesit 24 in. DI67 Free-standing Dishwasher

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Do not have any water being pumped into the upper arm spray bar. Removed and checked the feed tube assembly as well as the upper tube leading to the upper spray arm for obstructions and there are none. Also removed the ACCUMULATR and cleaned out the area.


Hi,We somehow got cut off, I am still around, we can chat here if that works for you. The link is here for the clean out ... KitchenAid Dishwashers

Remove the lower wash arm (1) by turning the nut (4) clockwise (right) lift the arm off, there is a bearing (3) (small thin plastic washer) under the arm, be sure not to loose it. Lift the tab on the back of the feed tube cap (2) and swing it to the right and lift up, this may need a bit of pressure to release it This is for my Whirlpool dishwasher DU1100XTP. I'm putting it back together and can't remember if the plastic washer goes on top or underneath the feed tube cap. Also how do I remo


This is not a tuff job plastic washer goes on top . and torx screws . you use a proper torx tip for the screw size . ( you can go to sears parts .com and put in model # and see a good break down of the wash arm s and t ... Dishwashers

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

We heard our bosch dishwasher just running last night but not circulating any water. I took out the drain screen and there was some dirty standing water so I used my shop vac to remove. It is still just running and no water is flowing. I was told it is the flood shut off? Please advise ASAP. Thanks


Hi\015\012\015\012The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The wa ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

GE Profile Dishwasher Mod No GSD4930Z02WW does not drain after the wash cycle. Cancel cycle removes a small quantity of water. The filter and strainer are clear. Water flow to the disposal sounds slow. Will I have to slide it out to access bottom pump area?


Hi,If you are hearing a slow flow coming to the disposal that is an indication that the dishwasher is working and the problem is in the drain system between the dishwasher and the disposer. This is caused by a blockage or clog in the drai ... GE 24 in. GSD4930Z Built-in Dishwasher

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Kenmore dishwasher Mod. #665 17729000. When I opened it there was a plastic tube laying on toip of the contents of the bottom basket: it looks like it could be the feed tube of water to the top basket, but I could find no way of reattaching it. I have not been able to find a detailed drawing of the machine on line. Help please.


W have herebelow the link of your model with all parts layout which we believe will helpyou see how everything is put together and also you can order any part thatmight need to be replaced. Don't thing we need to describe a ... Kenmore Dishwashers

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

Dishwashers My dishes come out of the dishwasher, which what feels like crumbs on them. Inside of glasses are that way also. I have to re-wash by hand after soaking in hot water to remove this. We use the Jet Dry and Ultra Jet Dry always, and usually use liquid cascade. Is there something wrong somewhere.


What you are likely seeing is the solids from household soap products. Household soap has too many "fillers", and doesn't dissolve fast enough for a 4 minute cycle. \015\012\015\012If you look into the bottom of your wash tank, I expect y ... Hobart AM14-253 Free-standing Dishwasher

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1893 seconds