Having problems with your Kenmore 16762 Dishwasher ?

Kenmore 16762000 will not run any wash cycles, only drains (cancels). all lights on panel seem to be working...


Answers :

Repair Help & Product Troubleshooting for Kenmore 16762 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kenmore 16762000 will not run any wash cycles, only drains (cancels). all lights on panel seem to be working...


... Kenmore 16762 Dishwasher

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

What's your problem?Ultra Quiet 3. Model# 665.16029400 The dishwasher water does not get hot during the wash cycle. There are no issues with blinking lights on the panel. Everything seems to work


... Dishwashers

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

I have a kenmore 665-15684. I have clear standing water in the dishwasher and doesn't seem to drain. No lights are on (or blinking) on the control panel and none of the buttons seem to work on the control panel.


It is very likely the computer has failed. \015\012\015\012Try to empty the dishwasher with a small container and try it on a short cycle to see if it starts the cycle.\015\012\015\012If there is no action then it is time to d ... Kenmore Dishwashers

I have a MDB4630AWS1 series dishwasher that is only a couple of weeks old. Suddenly, it now starts the wash cycle but then the Cancel/Drain light turns red, and it drains and stops the cycle. Check for items blocking the sprayers and looked for anything clogging the interior. It does this with all the settings. Seems to work for a few minutes, but then it just drains and stops. Any help would be greatly appreciated.


... Maytag MDB4630AWS Dishwasher

I have a Jenn-Air JDB9910AWB dishwasher. The problem I am having is everything seems to work fine until the drain cycle. It sounds like the pump is frozen. After selecting the drain button you can hear a click in the control panel followed by a 1-2 second growl in the pump but it doesn't turn or pump. I am assuming the pump runs in reverse for draining? Is it safe to assume the pump is bad?


... Jenn-Air JDB9910 Dishwasher

I have a 8 yr old model 16879 that stops apparently during the drain cycle. At this point the lights on the panel flash in what appears to be a coded sequence. Pushing the cancel button seems to try to start the motor for draining but immediately shuts off. Do I have a controller problem or something in the motor/pump area? David


Hi,It could be either...I would tear into the drain pump first and verify that nothing is stopping it from turning, then go for the controller if that seems to be okay...\015\012Dishwasher Problems - ... Kenmore 16879 Built-in Dishwasher

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Will not drain works fine up to the drain cycle then motor runs for a second kicks out control panel lights start to flicker


You probably have a block in the drain line to the sink if it is clear the the drain pump is burned out if it is the kind that is sepearte ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

We have a Whirlpool Gold Quiet Partner IV model#GU1500XTKQ0,the normal wash cycle starts buts just goes into hang mode @ 76min remaining and just continues to wash, is it the control panel or the timer circuit board, all lights seem to work on the control panel


I replaced the heater element on mine and that fixed the problem. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Currently the only setting that is working is Sani Wash. If I use any of the other settings the Intake Drain light comes on and everythig stops. How can the Sani Wash cycle work fine and no Intake Drain light when all other cycles trigger the Intake Drain light and won't continue to wash? Thanks,Karen


I decided I'd wait for the repairman; I don't want to have to pay additional money. ... Dishwashers

We have a whirlpool quiet partner iii. It was working fine and was opened mid cycle. Then it wouldnt drain. Then all the lights started blinking. At some point it drained the water out. We flipped the breaker and now just the normal cycle light is flashing. Flipped breaker again that didnt work. Tried the reset code hi temp wash and heated dry. Normal light still blinking. Help please?


See this causes and fix it. God bles you\012 \012 \012 \012 \012 Check Fault Codes\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

Kitchenaid dishwasher will not start. some panel lights work, and it will drain when CANCEL button is pressed


... Dishwashers

Whirlpool dishwasher:DU915PW PQ0 Hi :) It was working fine.opened it during the wash cycle. closed it again & nothing. no response from the control panel/no lights & water didnt drain. flipped the panel switch off for 10 seconds,back on again & still nothing???


I would check the fuse fist to establish if there is power to the appliance first\015\012\015\012Regards\015\012\015\012Ian ... Whirlpool 24 in. DU915PWP Built-in Dishwasher

Won't start. Seemed to be working fine a day ago. Then in mid cycle I opened the door because I was on the phone and it was too noisy (normal noise). Now , I shut the door and press start and nothing happens. No lights on the instrument panel. Nothing. Thanks.


You may have simply tripped a breaker, but if not it may be this.This may be a faulty door switch. If you look into the door locking mechanism carefully, you can see a small plastic bulb located either to the right or left of the locking Jaw. S ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

No lights Nothing, seems dead 6 months old working fine until yesterday Stopped it in the middle of cycle and would not resyart Tried breaker panel Power source fine Cleaned filters Tried reset


... Asko D5233XXL 24 in Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1510 seconds