Having problems with your Kenmore 16762 Dishwasher ?

We are having a small leak near the front valve or hose connection in our Kenmore dishwashers. This tends to happen when we are out of town and have turned the household water off. The dishwashers also has water in the bottom when we return. We have tried to set up the situation to make it leak in order to find it, but have not been successful. Have there been similar complants?


Answers :

Repair Help & Product Troubleshooting for Kenmore 16762 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We are having a small leak near the front valve or hose connection in our Kenmore dishwashers. This tends to happen when we are out of town and have turned the household water off. The dishwashers also has water in the bottom when we return. We have tried to set up the situation to make it leak in order to find it, but have not been successful. Have there been similar complants?


... Kenmore 16762 Dishwasher

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

We are having water leak from the bottom of our Roper Dishwasher door. THe model # is RUD5750DG3. I have taken the inside door frame off and found a small white rubber seal had dislodged inside. i placed it back in the only sopt it fits but water is still leaking. I have checked to make sure the water is not leaking from any where else on the dishasher. This occurs when the water inside is spraying and eventually fills up on the bottom. We no longer have our manual as the dishwasher cam


Try to fix the rubber seal which has come out by fixing it through super glue or apoxy seal which will stop the water spill and leakage.\015\012Please give more details of you dwasher ..... the Make and model so that i can send you the manual f ... Dishwashers

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

I have a Zanussi dishwasher model DA 6141. For some time now it has not been completely discharging the water at the end of a cycle. But sometime it does completely dicharge.Two days ago it started leaking water from its bottom at the end of a cycle.I tried to locate the leak but was unsucessfuly. All the external plumbing is ok andf there is no leak from the discharge pipe nor water intake pipe. So perhaps its something to do with the water pump?


Hello David,\015\012\015\012Have you removed and cleaned both filters and checked they are inserted correctly? I've uploaded the filter cleaning instructions to Flickr for you:\015\012\015\012 ... Zanussi Dishwashers

I just had a Haus slimline dishwasher delivered and have tried to set it up. I have followed the instructions to the letter but the water inlet hose keeps leaking out water when you move the dishwasher into place after attaching the hoses. I have tried the manufacturer's hose they provided and two spare i have in my cupboard. I even went out and bought some 3/4" washers and added extra washers to the inlet hose, but it still leaks. What is wrong?


It is possible the dishwasher inlet is set for low water pressure.\015\012\015\012Check the water pressure setting matches your inlet water pressure.\015\012It might help if you provide the model number of the dishwasher. ... Dishwashers

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

Dishwasher will not drain there is a bunch of water in the bottom. Tried running it through the cycle to make it drain out but still nothing just water in the bottom. Checked the sink and garbarge disposal to see if anything was blocking it or clogging it up but got nothing. Any suggestions?


Most likely a bad drain valve solenoid.\015\012It is attached to the side of the motor.\015\012The GE solenoids tend to burn out. ... GE Dishwashers

EdgeStar DWP45ES leaks mid cycle. Normal setting works fine, but rapid, Eco, and pre-wash settings cause water to leak from the bottom. Help!


Do you have the pressure regulator I showed at the Behring if the the video installed to you sink you can have any plumber come out and install one should stop the leakshead.ready(function(){ fixyaVid ... Dishwashers

Incomplete cycle My Miele dishwasher (3 to 4 years old) finishes, leaving the dishes dirty and wet. It seems that it may only be running through part of the cycle - I'm not sure but from the time I set it going to the time it switches off, it seems shorter than usual. The dishwasher is not emptying as it has a pool of water in the bottom. I have tried various settings and have the same problem. the inlet/drain light DOES NOT come on. I have soaked up all the residue on the bottom and cleaned out


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We purchased an expensive top of the line Fisher and Paykel 2 dryer dishwasher when we did a total Kitchen rehaul over 1 year ago. We have been noticing water sitting in the bottom of the bottom drawer that smells like sulfur dioxide and now see water is making its way through the maple cabinet to below the sink. None of the plumbing under the sink is leaking. We also purchased a Fisher Paykel gas oven/range at the same time. We notice the oven does not appear to close completely with a tigh


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Fisher and Paykel Dishwashers

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

I have a Frigidaire 1500 series with fully electronic control dishwasher. When I try to start it all the lights come on the display but not water enters the dishwasher. I have tried various settings including delay start but still the same outcome. The over-fill protector in the bottom of the dishwasher moves freely. What else should I try?


... Frigidaire Dishwashers

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My kitchenaid dishwasher has a bottom rack allignment problem. Especially when it is fully loaded the right rear pair of wheels often slips down off the bottom track and makes rolling the loaded rack fully in very difficult. I've already had a serviceman come out and he sent me a new bottom rack and set of four rollers and that improves the situation but does not eliminate it. Any similar complaints? Any easy fix before I call the service guy again?


Hello. If you have a new rack and new wheels the only fix to your problem is to either replace the dishwasher all together or NOT put as many items in the bottom rack. I am always bothered when anyone tells me they were sold a new rack because the ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Water leak My model is a GU2400XTPB1 The tub of diswasher has small hole where a screw is mounted on bottom of dishwasher. Leak is severe during cycle. I have tried epoxy but it will only hold up for a few washes. Will anyhing seal the leak and hold up? The dishwasher is only 2 years old..


Mine also started leaking. Element also too hot. Mine has a 20 year warrenty on the tub (which I was NOT aware of) Repairman came today and the whole tub unit and element will be fixed for free! Look in your whirlpool instruction book to see if your ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Kitchenaid ModelKUDI01TJBL0 only leaks at initial start up. Just after the water fills, the first few seconds of the wash cycle. It pours out the front door for a couple seconds than no more for the rest of the wash. It is level, no cracked arms, or loose pumps.Splash guard is in place. The float seems to be working, not too much water in the bottom. I am stumped. Although I do feel that it has something to do with the level of the water being too high, when the arm starts turning, it makes a


Is the unit level or leaning back if leaning back it is morelikey filling too much if level make sure the float moves up/down easy if not clean ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have an LG LDF6810ST dishwasher that has a leak on the bottom right hand side of the door. It appears to be leaking from inside the door itself. The dishwasher is 2 years old. I checked the inlet water to make sure connections were not leaking and they were not. I live in a rural part of Alaska so after talking with the LG help desk I'm pretty much on my own. Any ideas?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

After dishwasher was in cycle, I returned to kitchen and found puddle of water on the floor in front of it, water leaked down to basement. Haven't used since. Tried starting a cycle, but afraid to allow water to collect at bottom of unit.


The symptoms you describe, sounds like it could be caused by a worn door seal. Over time, these seals compress to the point where they no longer seal correctly, or food particles and grime get caught between the door and seal and leave small air gaps ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

My new Frigidaire dishwasher (FDB2415LFC) has not been used but is out of warranty. It has a leak with water dripping from two connectors (may be the heat coils) attached to the bottom of the dishwasher (located in the center). Why would water be dripping from this location and what is the repair solution? Should I try to return the dishwasher and obtain a replacement?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1686 seconds