Having problems with your Kenmore 16764 Dishwasher ?

No power on circuit board - Kenmore 16764 Dishwasher


Answers :

Repair Help & Product Troubleshooting for Kenmore 16764 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Elite 665 Dishwasher. The front control display has been partially working but the dishwasher still worked. Today when we tried to start it it will do nothing & it is getting the correct power. Would this be the control circuit board or something else?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

No power on circuit board - Kenmore 16764 Dishwasher


... Kenmore 16764 Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

Whirlpool dishwasher Model#GU3200XTPS0 No power to unit, Control panel does not have power check the circuit and outlet, are OK. is there any fuse inside the unit? is circuit board has any fuse?


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

I have a KitchenAid Whisper Quiet Dishwasher. Has been working fine. Circuit breaker seem to be working but control board is now not lighting up and buttons do not respond. Seems like no power to control board.


I may have leaked water into the mother board ciruitry. This can happen when there is a tiny leak or when steam gets in. Check with kitchenaid, that is a good product and kitchen aid will stand by thier equipment. ... KitchenAid Dishwashers

We have a kitchen aid dishwasher model # kudso1msso -- quit working and the control panel button lights are out so i assume there is no power to control panel. we have power at the plug every else looks ok. . could the internal fuse at the control panel be blown or the circuit board blown.


Sounds to me like a 'breaker' must be thrown; ... KitchenAid Dishwashers

I need to reset my Kenmore Elite dishwasher 665 16919 front panel. Drain tube was blocked and the dishwasher shut down. Now there is no power to the front panel. No circuit breakers were tripped.


... Kenmore 16919 Built-in Dishwasher

Hi kenmore model 587.15102800 dishwasher not getting any power breaker is fine . dishwasher is on its own circuit, is there a fuse in this model


If the breaker is fine then the next check will be the terminal box on dishwasher. usually that is where you would find your problem. let me know if this helps and if it did help me by sending a 4 thumbs up post Thanks! ... Kenmore Dishwashers

Is there a fuse or a circuit breaker in the Kenmore Ultrawash, quiet guard4 smartwash dishwasher purchased about 3-4 years ago? There is no power going to the machine--the outlet, the circuit, etc are all fine--but no lights light up on the panel and the washer wont start. Any suggestions?


There is a fuse behind the control panle its white and 1 inch by 1 inch ... Dishwashers

I have a kitchen aid dishwasher model kuds01dlsp3. The unit has no power. A repairman found that the power to the unit was fine and then said we needed a new circuit board. The charge would be approx 270. When I look at prices the whole assembly unit cost 179. wouldn't replacing the electronic component be much cheaper?


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. First\015\012thing is to verify that power is available at the power board of the\015\012dishwasher. Open the power board cover and check if the breaker is tr ... Whirlpool Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Benko dw600 dishwasher not working - no power. Have changed fuse and check circuit board but is ok there


... Dishwashers

I have a kenmore quiet guard 3 dishwasher 665.743833 it does not turn on when i select any cycle non of the lights tuen on i replaced the circuit board and the thermal fuse still nothing what


... Dishwashers

There is power to the main circuit control board, but no power exiting. unit will not run. no power to display.


There is a possibility that it could be a thermal fuse located in series with the hot side wire. If you are able to find it, and own an ohm meter, find out if it is open. ... Dishwashers

Kenmore Dishwasher No Power Model 665-16769000


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1937 seconds