Having problems with your Kenmore 16769 Dishwasher ?

Water is coming from between door and front bottom panel by the looks of it when running, seems to be on the rinse but will have to check again . but I have wood floors and the water isnt doing it any good we have checked all over inside to see what is wrong


Answers :

Repair Help & Product Troubleshooting for Kenmore 16769 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water is coming from between door and front bottom panel by the looks of it when running, seems to be on the rinse but will have to check again . but I have wood floors and the water isnt doing it any good we have checked all over inside to see what is wrong


... Kenmore 16769 Dishwasher

My 1998 GE dishwasher leaks. Into the floor, now I see stains on the ceiling below. What to check? Door seal is fine. The dishes get washed. Pressure is good to go. No water out of the front of machine, seems to be coming from below. Take panel off and inspect connections? How about line from sink? Is there a site with illustrations or video repair about this specific problem out there? Any help is greatly appreciated...


Check the water connection at the valve to the dishwasher. If the dishwasher only leaks when used then the motor seal is damaged. If leak is constant the the leak is at the supply to the dishwasher from the water supply at the valve\015\012 ... Dishwashers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Spilling water I have a Kenmore 665.15762 model dishwaher from Sears and it is spilling water throu the low part of the door. The draining is working well, is like as if the gasket is not good. I checked the gasket, but the only one I see is lateral and up and in good condition. Could be the floater too high ? Should I replace tge gasket ? Thanks for a quick reply. Viorika Aresteanu, Pierrefonds


... Kenmore Dishwashers

My Maytag PDB3600AWX isn't working. The motor hums as if its working but no water is in the tub. I did put a pitcher of water in the tub to see if it would pump out and it does. I don't know what else to check for. We have had lots of problems with this dishwasher, its never washed the dishes well and has flooded my kitchen to the point of having to replace flooring. I thought its was because we had just had new flooring installed and when they put the dishwasher back in the counter the hose was


... Maytag PDB3600A Built-in Dishwasher

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Maytag My Maytag dishwasher is leaking from the bottom. It is a mdbh940aww. it was never used before. It was wrapped in the plastic wrap when I bought the house in 2005. Now the old one just went and I want to put this one in. It fit nicely, works great but leaks all over the floor. It is level and I check most of the parts. I put a mirror underneath and it looks like the rubber thing isnt looking too good. Do I replace this? If so how?


I also had a mdbh940aww that leaked from underneath. You need to check out where the water is leaking from. Unscrew and remove the bottom front panel so you can view under the dishwasher. Start up the dishwasher and using a flashlight see where th ... Dishwashers

My hobart lxi pumps down after each wash cycle Already Tried: Cleaned all three water level probes Checked water inlet solenoid (all good) Checked inlet water pressure (all good) Checked drain pump which is supposed to pump out 3/4 of a gallon at the end of each wash cycle but it pumps 2-1/3 gallons then pops up the infamous wrench!


... Hobart 24 in. LXIH-3 Built-in Dishwasher

I noticed water on the floor (right corner) and my concern is that I have hardwood floors. It is not a lot that I can see but my concern is that water is leaking underneath where I can't see. It is 8yrs old so do I get it repaired or replace? I paid $379 for it.


Are you sure the water is coming from underneath the dishwasher? From the symptoms you described, this sounds like it could be caused by a worn door seal. Over time, these seals compress to the point where they no longer seal correctly, or food part ... Maytag 24 in. MDB4100 Built-in Dishwasher

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I noticed water leaking underneath my dishwasher through the floor joists to my basement. It was a small but steady drip through the joists. I turned off the water to the dishwasher and the leak stopped. I looked inside the dishwasher and there is still some standing water inside the dishwasher, but I cannot see anywhere that water is standing under the dishwasher. I am wondering if the leak is at the pump or at the door? But I see no evidence of the seal leaking.


This is probably the line that goes from the water inlet valve on the bottom of the dishwasher up to the valve leading into the dishwasher itself. It is probably a black corrugated rubber line. This is an extremely bad design, but the solution is s ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

While on vacation our house had been checked at one week later &again 2 weeks later, @ 3 weeks check, floor in front of dish washer & entire kitchen had standing water , as DW door was opened bottom of DW had water standing up to bottom of door . Water supply to house was shut off before we left. , Since we returned home we have used DW daily with no indication of where this water came from. Any ideas ? Thanks, Bob


Take a long shot. Say your mains leak a little, quite possible, and you machine's inlet solenoid valve leaks a bit, say about a litre a day - you probably would not notice it during the normal course of events, in a week it would leak a ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

We are having a problem with our LG Dishwasher. The machine is washing for about half an hour and then will stop and report an E1 error. According to the user manual this means "Water leakage in Hose connection" or "Water is leaked by damages". We have checked the diswasher's water connections and can't see any water leaking out. We have also cleaned the filers and checked the spray arms but that has not made any diffrence. Any suggestions what this error means and what we can try to resolve it


... Whirlpool 24 in. DU940QWD Built-in Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Our KitchenAid KUDS011JBS1 dishwasher sometimes leaks water on our kitchen floor. It seems to drip from the bottom edge of the door onto the floor. It's not a huge amount of water, but is enough to be a concern... it leaves a small puddle on the floor. What should I check and how do I fix this? I'm hoping it's an inexpensive and easy fix. Note that we've had this dishwasher for 8 years and have only noticed leaking during the past 6 months.


... Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

I've had a Miele G892 SCU PLUS dishwasher for a long time. Today a problem started that results in a flooded floor. Water keeps flowing into the dishwasher - even when the unit is turned off. It seeps in very slowly, but within15 minutes there is enough to overflow & flood the floor. My guess is that there must be some kind of sensor that isn't working, or the coresponding mechanical switch that shuts off the water is worn or slightly stuck open a bit? Anything I can do / check, short of the re


... Miele Touchtronic G892 Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I posted a question about my Maytag Dishwashere MDBH945AWW not starting, all lights function, and got a response from you seen here in this thread http://www.fixya.com/ThreadView.aspx?thid=6123266&prdid=519913 I was checking the water inlet valve for a clog and have determined with a meter that there is only 25 volts going to the water inlet valve. I notice a blue wire goes to the float switch which I already checked, there are 2 black wires one of which runs towards the back and cant see where


Hi,No, the lights can be working and a relay on the board can still be bad. These things can be very difficult even for a pro to trouble shoot as there can be many things that possibly can cause a unit not to start.From what you are sayin ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1011 seconds