Having problems with your Kenmore 16879 Built-in Dishwasher ?

Not drying The dishwasher will not dry. It heats up a little but that is it.


Answers :

Repair Help & Product Troubleshooting for Kenmore 16879 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Dishwasher Quietguard Standard and it has a little lock icon just below the heat dry button on the front. It is on and I can't start the dishwasher. How do I get the lock off?


Hold down for three to five seconds---or until light shuts off ... Dishwashers

Not drying The dishwasher will not dry. It heats up a little but that is it.


... Kenmore 16879 Built-in Dishwasher

DISHWASHER The diswasher works OK but won't dry the dishes. I've made a resistance test and get 28 ohms, it seems a little low for a heating element. Is this OK?


Dear Customer,Do all this for solving your problem,1check out your overheating prevension system like some fuse may be there for it,IT MUST BE ACTIVE FUSE OR LIVE,2than check your resistance value accr ... Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

We have a kenmore ultra wash dishwasher. i am unsure of the model number. i believe it was bought in 2001. the NO HEAT DRY button was blinking, so we replace some panel under the door. now the QUICK RINCE light is blinking. i tried the sequesce of WATER HEAT, NO HEAT DR, WATER HEAT, NO HEAT DRY, but that did not help. any other suggestions?? we have a family of 4, and it STINKS not having a dishwasher! litterally sometimes : )


... Kenmore 15129 Built-in Dishwasher

I have a GE Profile Dishwasher, Model# PDW7880J03SS that doesnt dry the dishes. I pulled out the dishwasher and checked the heating element for continuity with my ohm meter and got a closed circuit reading. I tested the voltage going to the heating element and got a 124V reading. However the dishes are still soaking wet after the drying cycle. What am i missing, what else could be wrong with the machine that the dishes won't dry at all?


Hi\015\012\015\012Check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll ... Dishwashers

Kenmore dishwasher 665. heated dry light blinking. dishwasher won't turn on. How do I get the heated dry light to stop blinking?


... Kenmore 17439 Built-in Dishwasher

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

I have Jenn-Air dishwasher that I use the heated dry cycle for. Last night at 11:00 pm or so I ran the unit. Today at 10:00am when I opened the door steam barrelled out and everything was so hot to the touch I gave myself a significant burn when grabbing a non-metal item in the dishwasher. Should I be concerned there is a problem with the entire unit or just the heated dry cycle? Should I be concerned about fire danger due to a short?


... Jenn-Air 24 in. JDB2100AW Dishwasher

Model no. MDB6100AWW. Just unloaded the dishwasher. Shut the door and immediately heard clicking (regular cadence). All indicator lights (arrow-shaped) for clean, dry, wash and heating delay were blinking. Opened the door, waited a few minutes, closed the door. Now, just the "Clean" and "6 Hour" arrow indicator lights and "Heated Dry" button light indicator are still blinking continuously. Cannot override. What's going on? Dishwasher came with the house when we purchased it 6 years ago. Proba


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash-heated dry ... Maytag 24 in. MDB6100A Built-in Dishwasher

The water didn't drain . I washed a broiler pan and used pot scrubber and heated dry. I opened the dishwasher during heated dry and greasy water is still in the bottom of the dishwasher. Could it be a grease clog?


Yes take a smaller hose and put through the drain hose then push drain/cancle ... Hotpoint 23 in. BFI62 Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I have a GE Monagram dishwasher 1999 /- model ZBD 5900/5700 It is stuck on Heated Dry cycle. Would not drain for along time, than it finally drained but still stuck on Heated Dry. Turned breaker off and on several times did not help. Still stuck on Heated Dry no other buttons work


... Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Bosch DLX series dishwasher and no manual. The heat dry doesn't work or at least not well. There is no heat on/off switch. How do I ensure the heat is on so I can stop drying my dishes by hand?


... Bosch Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1810 seconds