Having problems with your Kenmore 24 in. 15079 Built-in Dishwasher ?

The clean light in my Kenmore dishwasher keeps

\015 The clean light in my Kenmore dishwasher keeps flashing and the dishwasher won't turn on when you press start.\015

Answers :

It has to do with the water temperture, either the water entering the dishwasher is too cold and the heater can't get it up to temp, or the heater unit has problems... Push the Air dry ,then the sani wash buttons a few times and all the lights will light, it resets the computer .
Repair Help & Product Troubleshooting for Kenmore 24 in. 15079 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


Only reset you can do is unplugging power cord for 10 minutes.The control panel it is probably faulty and in need for replacement. ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

My Kenmore dishwasher, about 5 years old, is not cleaning well any more. Glasses look cloudy,and I assume the bowls and plates are not clean also, but that's harder to detect unless I hold them up to light. I use a rinse agent. What's the problem? Is it worth having a service person look at it or should I just get a new one? It's a Kenmore Elite ultra wash dishwasher.


Although I used my credit card to pay for the live chat, it bounced me out before the service person could respond. So I tried another service and two people who do home repair told me what the problem was and what it would cost to fix it. Since the ... Kenmore Dishwashers

I have kenmore quietguard 3; model 665-17022401. The clean light flashes at the end of every wash. The codes work to reset the light, but it reappears after every wash and the dishes are not clean. Any thoughts?


... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

My kenmore 575-0 dishwasher is blinking green on the clean light and every time i try to start the machine the clean light blinks even more and doesn't wash the dishes.


Mine started doing that 3 weeks ago. Did you get a 'fix' for the problem? ... Kenmore 24 in. 16029 Built-in Dishwasher

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem?


Please accept this answer - and re-post your question with the following information:1. Does the washer work at all?2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit?3. Is the ... Dishwashers

My clean light is blinking on my kenmore 16029 dishwasher and it won't start after I push the start button. The clean light is following a pattern of blinking 7 times and stopping, then repeating over and over again.


... Kenmore 24 in. 16029 Built-in Dishwasher

Blinking clean light on my Kenmore 665.17052400 7 times Did the "reboot" normal wash,heated dry sequence which made the machine work for a while. then it would go less times in between needing to be "rebooted", now it will not go through a cycle w/o the clean light blinking even following a reboot. what is my next step? I have heard that this means the microprocessor will need to be replaced. is it even worth it?


No its about a buck forty but im sure you could do it your self ... Dishwashers

The green clean light is flashing on my Kenmore Elite Ultra Wash dishwasher. After the reset sequence, the washer will run only 1 part of it's washing/drying cycle, then flash the clean light again... I have only owned it about 14 months, and this is the first problem I have had.


You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Kenmore 24 in. 17032 Built-in Dishwasher

Kenmore Elite Dishwasher model 665.16262402 has the clean light indicator flashing and it won't let me start a new load. Normally the light is on steady when a load is clean. Once the door is open


... Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


If the clean light flashes 7 times, pauses then repeats...If the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non responsive ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore Elite Dishwasher clean light ind flashing and won't start


You will have to reset the console. To do this, close the door and press these buttons in sequence...-high temp wash-heated dry-high temp wash-heated dry...all the lights will turn on briefly and the machine ... Kenmore 24 in. 15142 Built-in Dishwasher

Kenmore 665 - clean light blinks 7X - help


Get its circuit kit checked, it is malfunctioning. Custom Parts For Mercedes ... Kenmore Dishwashers

Kenmore Elite Dishwasher clean light ind flashing and won't start


That means the control sensed that the heater in the d/w did not operate 3 times in a row. so the unit locks out. First remove the kick plate and you may have to pull the unit out from under the cab, but check your heater. u ... Kenmore 24 in. 15142 Built-in Dishwasher

Clean light flashing Kenmore 665.16032402


... Kenmore 24 in. 16029 Built-in Dishwasher

Kenmore Ultrwash, limited wash cycles, dishes not the best clean, red drain light on during wash


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

I have a Kenmore mdl. #16032. I have a blinking clean light. Due to this Light or problem the unit will not operate. Prior to this light the dishwasher was a little noisy. What do I need to do to resolve this problem?


I think this is related to the wash arm getting obstructed by either a pan or some spoon stuck at the bottom. That could be the noise you mention.\015\012\015\012\015\012I have seen people fix the clean light flashing with a sequenc ... Kenmore 24 in. 16032 Built-in Dishwasher

Blinking clean light light on kenmore ultrawash quiet guard 4 after a cycle.The unit will not clear this blinking light or allow me to resart another load. any answers?


Most of the time this meens the heat element is burnt out. if you can get to the bottom of the dishwasher and remove the wires and nuts holding the element in you can replace it.\015\012good luck ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1248 seconds