Having problems with your Kenmore 24 in. 15689 Built-in Dishwasher ?

Dishwasher not filling all the way, - Kenmore 24 in. 15689 Built-in Dishwasher


Answers :

Hi,
There's no water entering the machine
If there's no water entering your dishwasher, check these:

Water-inlet valve
Float switch

Water-inlet valve
The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.


Float switch
The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

good luck.........
Repair Help & Product Troubleshooting for Kenmore 24 in. 15689 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher not filling all the way, - Kenmore 24 in. 15689 Built-in Dishwasher


Hi,There's no water entering the machineIf there's no water entering your dishwasher, check these:Water-inlet valveFloat switchWater-inlet valveThe water-inlet valve lets water enter the machine. If thi ... Kenmore 24 in. 15689 Built-in Dishwasher

Kenmore dishwasher fills but does not drain - Kenmore 16602 / 16604 / 16609 Built-in Dishwasher


May be clogged? ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

No water is coming thru the water valve to fill the dishwasher. The water is turned on. I had a Kenmore portable dishwasher and we just converted it to a built-in. The electricity is on and the water line installed. When I turn on the dishwasher, it comes on ok but no water is coming into the machine.


Most probable cause a faulty intake solenoid. OK start simple and go from there.If your have power and light etc come on then we know you are good for power. I'll assume that is OK. If\012you are not getting any li ... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

Why would my dishwasher not fill? - Electrolux Kenmore 24 in. Built-In Dishwasher with 5-level Precision Direct Water Delivery System Dishwasher


Check the following:\015\012\015\012Make sure the water is turned on to the dishwasher\015\012\015\012When you press the start switch, you should hear a "click" which is the water valve opening - if no click, you should check ... Electrolux Kenmore 24 in. Built-In Dishwasher with 5-level Precision Direct Water Delivery System Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Dishwasher will not stop filling up - Kenmore 24 in. 17032 Built-in Dishwasher


It sounds like the incoming water solenoid is stuck open. ... Kenmore 24 in. 17032 Built-in Dishwasher

Will fill but not drain - Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher


\012\012Hi,\012Here\012is a tip that I wrote that will help you with your dishwasher not\012draining problem...Dishwasher Problems - ... Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher

I have a Sears Kenmore Elite dishwasher Mod. # 665 - Ser.# FJ4805735 that intermittantly skips the wash cycle and pumps the hot water out just after filling. This unit was built in 2000 but the entire drive unit was replaced about 6 yrs. ago. If the problem lies in the electronics is it worth a do it yourself repair. I have an antique (1970'S) appliance repair background and electronics is not my forte. Money is tight and I would like to squeeeeeeeze another couple of years out of this appli


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Would you be able to supply the complete model number. The Kenmore elite dishwashers where made by many different manufacturer's over the years, even within t ... Dishwashers

Top rack pulls out. Only half way - Kenmore 24 in. 15932 Built-in Dishwasher


... Kenmore 24 in. 15932 Built-in Dishwasher

My dishwasher 15789 kenmore built in seems to have shorted out it was clicking on and off... i secured the latch better and restarted - it stopped right after filling... no it won't respond. there is power going to it


... Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

Kenmore Dishwasher leaks from fill spout


... Kenmore Dishwashers

Kenmore built-in Dishwasher #15149 runs for 3 hours or more


... Kenmore Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Kenmore dishwasher model 587.1414 -- stopped after filling with water, but dial continues countdown


... Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Kenmore dishwasher will not fill with water model no 630.1609406. It will run a full cycle but not fill. Water was temp shut off to replace kitchen sink and now dishwasher won't fill with water. No fill valve that I can see cleaned filter but still no water.


First, are you sure that the machine is not filling?\015\012I go on calls all the time for this problem and it turns out than the machine fills but the wash motor does not run.This leaves soap in the bottom of the DW so it looks like it did not ... Dishwashers

I have a AEG OKO_ FAVORIT 4040 dishwasher which has had very little use despite its age. The problem is that the switch that detects an over-fill is activated all the time and the pump continues to try and empty an already empty dishwasher even when the main switch is turned off, the only way to stop this is to turn it off at the power point I have had some sucess deactivating this switch by tilting the dishwasher forwards however because of the angle it sometimes overflows when filling. The ma


Hi there,This could be a problem on the control board of the unit. It could be faulty and need replacement or you may try to access the board and try to clean it.Make sure upon doing this all electrical connection to the unit ... Dishwashers

I have a Kenmore Elite dishwasher (2004) and recently it has been leaking internally at a very slow pace. When not in use it will slowly fill until the floor of the unit is filled and then leak onto the kitchen floor unless we press the drain button and then it drains completely. The water seems to be coming from the front of the washer, potentially from the door itself. The amount of leakage is barely discernible but will fill over the course of a 24 hour period. The dishwasher otherwise wo


Hello,\015\012The water is admitted into the dishwasher through a little magnetically controlled valve underneath your dishwasher. This valve opens and shuts electrically. There is a little plunger in it that is pushed shut by a spring when no ... Kenmore Dishwashers

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

I have a frigidaire built in dishwasher, about 5 years old. Model #FDBL960BB0. I had a clogged sink which caused my dishwasher to back up. Had the drain unclogged, went to start my dishwasher, it's making the regular cycle noise but is not filling with water. Is there some sort of safety switch that needs to be reset before it will fill with water?


Yes lift your float,,and drop back into place ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1983 seconds