Having problems with your Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher ?

Kenmore Dishwasher 665.15789300 not washing, but gets water

\015 Dishwasher didn't wash, upon investigating the problem, notice the lower sprayer arm nut was broken. I replace the nut, and the dishwasher still does not wash.\015

Answers :

The chopper blade assembly with in the pump housing is either clogged or broken, to get to it, you must remove spray arm and remove screws from filter housing. These are size 20 torx, inside sump are 2 more screws size 15 torx, after these are removed you can clean out chopper or replace it.
Repair Help & Product Troubleshooting for Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks


SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?


I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers

I just bought a used Kenmore standalone dishwasher and ran it for the first time. The dishes on the top did not get clean and the soap did not come out of the closed soup dish. at one point I took a shower and was wondering if that might have influenced the water pressure enough to cause the problem. Is the soap supposed to open during the wash and could the poor water pressure prevent the top shelf from getting properly washed?


The inlet filter is probably clogged. Try letting it fill up. Open the door to stop it right after it starts to wash Pour a gallon or two of hot water in and see it it works better Stop and do this everytime it goes to fill up. If the door opens ... Dishwashers

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.


... Kenmore Dishwashers

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

My Kenmore ultra wash dishwasher fills with a little bit of water but does not spray water and does not proceed through the wash cycle. Any advice? We had problems yesterday with blinking lights and not able to get anything to work except the drain. then we followed a sequence of pushing buttons and it solved the first problem.


The spray arm rotates based on the water pressure coming out of them. If no water pressure, then no rotation. You probably have a clog on the intake hose. You can pull out the dishwasher, tip it forward so you can get to the bottom and then rem ... Kenmore Dishwashers

Broken dishwasher We recently had a plumbing problem that resulted in the kitchen sink overflowing and flooding the kitchen. The cabinets to the left of the sink were full of water and the dishwasher to the right of the sink will not work. It says it is washing and using two different washing modes, but I cannot get it to start over. What can I do? It is a Kenmore Quiet Guard 2.


If there is no water in the dishwasher - i.e. it had finished a cycle, but now it is just the indicator lights that are on, then the chances are some water has got into the control system. It will probably dry out, given time. (maybe a number of days ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

Water tower The water tower came off of my Kenmore Ultra Wash III dishwasher. I cannot figure out how to get it back on. There is a gasket on the water arm. Does the water tower actually go on top of the bottom rack? And if so, then how?


I had the same problem finding a Water Tower laying in the bottom of the dishwasher. Solution is to simply lift the bottom rack and insert the tower into the center-most square hole. Twist the tower with the large lip on the bottom of the rack and th ... Kenmore 17439 Built-in Dishwasher

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

I have a Kenmore Ultra Wash dishwasher. Model # 665.15685791. All of a sudden it acts as if it is getting too much water. Water comes over the edge of the interior tub during the rinse cycle, and ends up on the kitchen floor. Is there an adjustment I can make? There doesn't seem to be any blockage, as all the water does drain out of the tub during the regular cylcles. Vince Woodwick [email protected]


Hi, there is a water level sensor and if this is happening then it maybe faulty, and need to be replaced, either this or the controller board that controls it has gone faulty, one needs to troubleshoot to tell.\015\012\015\012\015\012 ... Kenmore Dishwashers

Kenmore Dishwasher 665.15789300 not washing, but gets water


The chopper blade assembly with in the pump housing is either clogged or broken, to get to it, you must remove spray arm and remove screws from filter housing. These are size 20 torx, inside sump are 2 more screws size 15 torx, after these are remove ... Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher

Kenmore Ultra wash III will no longer stay connected to faucet after filling...what part should I replace the hose or the faucet adaptor? When we turn the faucet on to start up the dishwasher it falls off...when we finally get it to stay connected with water on...it will fill but then falls off again...get it to stay on, it empties, but then after it has completed filling up again it disconnects from the faucet.


If your adapter that hooks up to the faucet has 4 little white plastic jaws inside it then it can be rebuilt. there is a kit that replaces those 4 jaws, the spring, the attaching clip and the internal seal.. usually runs around 10 buks or so. if i wa ... Kenmore Dishwashers

I have a kenmore ultra wash dishwasher and it doesn't seem to get to the dry cycle. Left on it will wash and drain and repeat over and over. I have to manually press the drain/reset cycle to drain the water.


... Kenmore 24 in. 16182 / 16189 Built-in Dishwasher

I have a Kenmore 17659 Ultra Wash III and when I run it, the water doesnt appear to be getting into the dishwasher. It turns on and goes thru the cycle but the dishes dont get cleaned.


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Tr ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

Our Kenmore dishwasher 665.1726 doesnt seem to be cleaning as well. LAst time this happened a serviceperson cleaned out a filter where food debris had clogged the water flow. We were able to take off the bottom wash arm but couldn't figure out how to get the filter off (there are 4 screws holding it in place and one is under the plastic arm that caries water to the sprayer.


I had the same problem!\015\012\015\012The arm WILL come off....you have to pull the screen off. ... Kenmore 24 in. 15689 Built-in Dishwasher

We just installed a new kenmore dishwasher yesterday. Model 13242 It has been running for almost2 hours and is still on the washing cycle--no water in it however--is this normal? I'm in a bit of a panic as we are canning and I need the jars washed--we didn't get a manual with it as it was a floor model so I don't know how lon the normal cycle ids. HELP


THAT IS NOT NORMAL!!!!!!! A normal wash and dry cycle will take approx. 2 hours in length including drying cycle.\012You should see that water has been present in the machine within the first 2 minutes of the start of the wash cycle, you shou ... Kenmore Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Kenmore elite dishwasher 630.1630 will start but once in wash cycle won't change cycles,also top rack not getting water


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Kenmore ultra wash dishwasher 15835 it runs fine, but when is sets after its finished it get water in it and you have to press cancel to drain it again. Any idea?


Water inlet valve needs replacing. (about $50 for the part)\012The valve is leaking and allowing water to enter the dishwasher even when it's off. You can turn off the supply line shut off between uses until you get the part. ... Kenmore Dishwashers

I have a Kenmore dishwasher model #665.13842K601. The problem that it has is that it does not seem to be pumping the water around the tub after it fills. It will fill and drain fine but will not wash. I have removed the spray arms and checked all the parts that I can get to from the inside but fear that it may be a pump or jammed impeller. it does make a faint buzzing sound when it should be operating. Any input would be great. Thanks, Matt


It sounds like you have a circulation problem which means that the circulation pump has gone bad. \015\012Circulation pump - http://www.appl ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1791 seconds