Having problems with your Kenmore 24 in. 15932 Built-in Dishwasher ?

No lights on touch pad kenmor dishwasher 665.17364301

\015 Power to one side of diode door switches ok washer dosent do anything\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 15932 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No lights on touch pad kenmor dishwasher 665.17364301


... Kenmore 24 in. 15932 Built-in Dishwasher

Kenmore dishwasher ultra wash, no lights on touch pad working


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

Ge dishwasher PDW9280J00SS no lights touch pad


... Dishwashers

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

I have a GE pdw9880 dishwasher with the hidden soft touch pad buttons. All the buttons light up and beep and go through their selections except for the start button. The start button doesn't light up or beep and the dishwasher doesn't run. Do you have any idea what might cause this? Thx


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Kenmore Elite dishwasher with electronic controls. When I set the controls press the start pad and close the door it will not start. The light on the start pad just continues to blink. This happened about six months ago and the Sears serviceman pressed two of the control pads simultaneously and this reset the controls. Everything worked after he did this. What are the two control pads that you press to reset the controls?


This is difficult to find out. Try different combinations. Otherwise get the information from the SEARS serviceman. ... Dishwashers

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

I got a GLD4400N00WW dishwasher, The normal and headed dry lights blink. I already replaced the touch pad. Once your reset the d/w and shut the door the lights will come on and you can start the cycle. Once you press the cancel button the lights blink and thats it....


... GE Profile PDW8400J Built-in Dishwasher

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

I have a Kitchen Aid Dishwasher Model KUDC10IXWHO that the touch pad does not light up or will fuction


... Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Kenmore 665.16529000 When we put the dial to pots and pans the diswasher fills up and cycles through, when the dials moves to normal wash, it fills up and cycles through again. When the dial gets to light wsh we can hear the motor running but nothing is happening, but the soap door opens soon after. The heating light comes on and the inside of the dishwasher gets so hot that it has melted our big plastic tumbler cups on the top rack and makes the counter top extremely hot to the touch. The dial


... Dishwashers

My Maytag Dishwasher MDB7601AWB is not working. The Rinse Only and Tuff Scrub Plus lights are the only ones lit and the control pad is unresponsive when pressed. Do I need a new control panel or just a touch pad?


... Maytag Dishwashers

I have a Jenn-Air dishwasher model #JDB1100AWW. When I try to start it, the start light won't turn on or the delay light if I try that option and it won't run. I've replaced the control panel/board and still nothing. Is it possible the touch pad needs to be replaced?


... Jenn-Air Dishwashers

Vulcan vsa regency 500e touch control. I have light in dishwasher but when you close the door the main control panel touch pad will not function. Can't operate machine


... Dishwashers

Kenmore Elite Dishwasher 0 Lock light on


Hold down the "air dry" button for 4 seconds ... Kenmore 24 in. 16983 Stainless Steel Built-in Dishwasher

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My Maytag dishwasher will not start. I have a concealed touch pad on top. This is the third time it has done this. Every light works but the start button. If I wait a day or two it will start working again. I have arranged a service call twice and had to cancel both times because it was working. HELP


... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

FRIGIDAIRE GALLERY 4000 DISHWASHER MODEL NUMBER: GLD4355RFB1 IN THE MIDDLE OF CLEANING CYCLE...A "ER" CODE IS DIDPLAYED AND LED LIGHTS BLINKING ON THE TOUCH PAD. I PURCHASE IT 1/2008.


Try first unplugging power and see if this reset the appliance. ... Dishwashers

THE START BUTTON ON THE TOUCH PAD WON'T LIGHT UP SO DISHWASHER WON'T TURN ON. ANY IDEAS?


... Jenn-Air 24 in. JDB1080AW Built-in Dishwasher

Light keeps blinking on quick rinse, and will not cancel when cancel button is pushed.it just keeps blinking no matter what pad button i push.machine will not work at all. kenmore dishwasher model 665 15717000


... Kenmore Dishwashers

As soon as power is turned on to dishwasher there is a beeping noise and F1 is lighting up on touch pad screen. What do I need to do?


Hello, welcome to FixYa.\015\012\015\012The first question I can answer easy, what you first need to do is provide a make and model of the unit in question :0)\015\012\015\012I will watch for your reply.\015\012\015\012\015\012macmarkus :) ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1566 seconds