Having problems with your Kenmore 24 in. 15992 Built-in Dishwasher ?

This is a 15972 that does not drain. I think the drain is clogged, how do I access it from inside the machine? I have removed everything to the point of the impeller..... I pulled the drain line from the sink and tried to blow into it to see if that would clear it...did not work.


Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 15992 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

This is a 15972 that does not drain. I think the drain is clogged, how do I access it from inside the machine? I have removed everything to the point of the impeller..... I pulled the drain line from the sink and tried to blow into it to see if that would clear it...did not work.


... Kenmore 24 in. 15992 Built-in Dishwasher

Hotpoint Dishwasher Bought it new 2 weeks ago. Seemed to be working ok. Last night it started leaking out the front door (suds). I disconnected the drain line (tried to blow through line to tub, NO GO) so I started it and ran it into the sink. It seemed to be flowing OK, but there is still about 1/2 inch of water inside washer. Is this OK? Model # HDA3400G02BB


Water will not come on. started 3 months ago being erratic, some time it would work, some time it would not. Now it has gotten solid. Everything runs except water, therefore no wash. ... Dishwashers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

My Whirlpool dishwasher will wash fine, but when it drains, it's a slow trickle. I've snaked the line from the sink to the washer, but I can't find a clog. If I try to blow into the drain pipe all I accomplish is almost passing out. I can't blow all the way through it. When I hit the drain button, I hear the solenoid kick on with a rattle, then just a hum. Like I said, I just get a trickle, and the basin never drains completely. It's driving me crazy! Help? Thanks.


In the bottom of the dishwasher, there is a screen. Remove it and clean it and the drain underneath it. Make sure the POWER IS OFF before you start. ... Dishwashers

My Whirlpool dishwasher will wash fine, but when it drains, it's a slow trickle. I've snaked the line from the sink to the washer, but I can't find a clog. If I try to blow into the drain pipe all I accomplish is almost passing out. I can't blow all the way through it. When I hit the drain button, I hear the solenoid kick on with a rattle, then just a hum. Like I said, I just get a trickle, and the basin never drains completely. It's driving me crazy! Help? Thanks.


Ok, don't fret too bad, help maybe just reading.Disconnect the drain hose from the sink/garbage disposal, get a big bucket, stick hose in bucket, making sure that end of drain hose does not get lower then the bottom of dishwasher. Turn di ... Whirlpool 24 in. DU1055XTPS Stainless Steel Built-in Dishwasher

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

After working perfectly for years, I came home yesterday and the dishwasher had gone through it's whole cycle (including drying) but the bottom was fully filled with water. I emptied the dishwasher and tried to put it through a "rinse and hold" cycle to see if it would drain, but that didn't work. I pulled out the filter--it's clean as a whistle. Any thoughts? PLEASE?? thanks!


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain out ... Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

My Professional series model fdbb4365fc2 Makes a slight intermittant thumping sound a few times when its started and than after a few moments it shows the error code uo. For a while we could cancel and try a different cycle and it would work. I checked drain hoses and sink trap all looks o.k. What is my options


... Frigidaire Dishwashers

Kenmore elite 1393 worked fine for a week or two then began to stop in mid cycle,we could drain the water and try again but would shut off almost immediately. sometimes trying to restart it there would be NO power to any buttons, after waiting for awhile the buttons/lights would work again but the washer would not run a full cycle.blue light would light then go out within a minute or so.


... Dishwashers

After putting too much down the garbage disposal, the sink will not drain and the dish washer (Whirlpool Quiet Wash) will not drain. I have disconnected all sink drain pipes and snaked the main line to be sure lines are clean. The drain hose from the disposal to the washer seems clear. What should I try next?


You need a longer snake had one on friday that wa about 40 feet out it took two trys to get it good luck ... Dishwashers

A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?


The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers

Frigidaire 2405 Dishwasher has a direct drain into the floor and is too far from the sink to be able to drain into the sink pipes. Can I add a loop of drain hose from the floor drain up to the counter height, about 30", then back to the floor to mimic the loop that would be created by running to the sink drain? I have been told that these new types of dishwashers require water remaining in the pipes to work properly. Thanks, John


There will be no problem with you adding more drain hose to the unit. ... Frigidaire Dishwashers

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

The Intake/ Drain light is on. It appears that the machine is not draining and that possibly the pump is not working properly. The drain line appears to be clear though I haven't pulled out the unit to check the drain line at the machine. Any suggestions?


... Miele Touchtronic G832SC Built-in Dishwasher

MY FRIGIDAIRE DISHWASHER WILL NOT DRAIN. MOTOR ONLY HUMS DURING DRAIN CYCLE. OTHER THAN DRAINING IT SEEMS TO WORK FINE. DAY IT QUITE WORKING SINK BACKED UP AND WOULD NOT DRAIN


If there is still water in the dishwasher take the drain hose off from under the sink and use a large pot or mop bucket and but the unit into a drain mode usually by cancelling the wash cycle if the unit still does not drain.Then use a wet dry shop v ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a Bosch dishwasher that was working just fine until I spilled a bag of uncooked pasta. I sent the pasta down the drain and ran the garbage disposal, subsequently clogging the pipes. I had to get a plumber to fix the drains, but he wouldn't unclog the dishwasher. I have tried myself to go under the sink and drain some hoses, but it didn't work. I also put some baking soda and vinegar into the drain, but no luck. What can I do?


It may simply be where the dishwasher drain attaches to your garbage disposal. There should be a hose clamp and can easily be taken off. If the clog's not right at the connection, chances are it's far. If there is an air gap, it will be within a f ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Dishwasher: Whirlpool Gold Quiet Partner. Has worked fine until had a house plumbing blockage which made water pool in the bottom of the dishwasher as well as kitchen sink. Tried to get it to drain at first using keypad. Drain light clicked on and then off because there was nowhere for water to do. Manually emptied most of the water, then "Cancel/Drain" worked if I held it down quite a while. House plumbing is now fixed. However the keypad only works sporadically now. Some buttons do so


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

Main sink and d/w did not drain. Used plunger heavily. Did not work. Had main line jetted out. Now sink drains but d/w still does not. Older model Kenmore #1661590 Thank you


Hello playultimate,\015\012I am assuming that your dishwasher drains either directly into your sink or through a garbage disposal as part of your sink. Regardless of which method is used, you need to verify that your dishwasher drain system is ... Dishwashers

I have a Bosch Dishwasher SHU3302UC/14 that will not drain. We initially thought the problem was the disposal because water kept backing up into the sink. We replaced the disposal, removed the dishwasher plug in the disposal, but the dishwasher still does not drain. I would like to check the drain line, but am unable to access it. I removed the kick plate and the screws that secure the dishwasher to the underside of the counter, but the dishwasher will not move. Can you access the drain li


... Bosch Dishwashers

Will not drain, clogged with washed off jar labels and a few metal scrubber parts; Can I pull of the washer arm and drain parts to eliminate the clogged drain? I tried 1/2c. vinegar to rinse out. It just would not drain.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I am trying to install a new Maytag MDBH945AWB Dishwasher and have to run the drain hose under the machine in order to get it to the sink. Each time I try to use the hose that comes with the machine it snaps in two and breaks. I have tried to look for a replacement hose that would stand up to the abuse but all I can find is the original. Is there a replacement I can get that is more flexible than the one that comes with it? At this point I am rather embarrased about going back to Home Depot


Hi...home depot sells clear PVC hoses, They come in various lengths up to 100 ft. You can use hose clamps to connect it to the T-fitting. ... Dishwashers

Avanti dishwasher stopped working. I have checked breakers-the dishwasher lights do come on-it will not cycle. When it first stopped working, the motor was working, but the dial would not move. I tried to cycle it to drain the water, but then nothing more happened.


... Avanti 18 in. DW19PSS Platinium Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1725 seconds