Having problems with your Kenmore 24 in. 16014 Built-in Dishwasher ?

Clean lite is flashing

\015 The clean lite on the front panel is flashing and machine after pushing the start button will not start.\015

Answers :

Hi,

This is an indication that there was a failure to heat the water properly. I have put together some instructions on how to reset the control so you can use the dishwasher and some things to check to avoid this problem again. Follow the link below and let me know if it was helpful.

Clean light flashing
Repair Help & Product Troubleshooting for Kenmore 24 in. 16014 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

Kenmore elite clean lite is flashing won't shut off.unit won't work modle #66516912001 serial#fk4402228.it flashes 7 times over and over.i shut off all power turn back on still flashes .i replaced electric board in door panel new button panel


I have a service bulliten on this if you will email me at [email protected] ill send it to you its too big for here ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

Clean lite is flashing


Hi,This is an indication that there was a failure to heat the water properly. I have put together some instructions on how to reset the control so you can use the dishwasher and some things to check to avoid this problem again. Follow the ... Kenmore 24 in. 16014 Built-in Dishwasher

Clean lite keeps flashing will not start whenstart


The thermistor beneath the accumulator inside the sump\015\012detects the water temperature as it begins the first 8 minutes of the main wash\015\012cycle. During this time, the controller expects the thermistor to detect the\015\0122-4 degrees rise ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

DISHWASHER QUIT WORKING IN ALL WASH CYCLES EXCEPT SHORT WASH CYCLE. YES I HAVE TRIED TO FIX IT. I HAVE REPLACED THE CONTROL MODULE WITH A NEW ONE. ALL WIRING LOOKS CLEAN AND IN GOOD ORDER. NO EVIDENCE OF CORROSION. NOW UNIT WILL NOT WORK AT ALL, BUT "CLEAN LITE INDICATOR' IS FLASHING IN SEQUENCES OF 7. I HAVE FOUND THE SCHEMATIC SHEET BEHIND THE KICK PLATE. AND USING IT I HAVE TRYED TO USE THE DIAGNOSTIC PROGRAM BUT CANNOT FIND ANY PROBLEMS. AFTER DIAGNOSTIC PROGRAM IS COMPLETE THE DI


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

Green clean lite continues to flash. have removed and re installed power. this is preventing the start of the clean cycle, how can I reset this?


... Kenmore 24 in. 17012 Built-in Dishwasher

CLEANING LITE IS FLASHING OFF AND ON THE DISHER WON'T TURN ON.CAN'T GET THE TO TURN OFF


This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:http://www.f ... Dishwashers

Clean lite flashing - Kenmore Dishwashers


Hi If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. ... Kenmore Dishwashers

Kitchen aid dishwasher kudk031twho gets water, drains, soap will not disolve, runs thru all cycles, once the clean lite flashed 7 times, after reseting code never happened again.


... KitchenAid Dishwashers

Whirlpool model du1100xtpq6 machine will not start clean lite flashes 7 times stops and repeats must be code 7 blinks only drain pump runs when drain/cancel button pushed


Hi, this is an indication that the water did not heat properly. Follow this link to some instructions I put together to help solve this and reset the control so you can use the machine again. ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Dishwasher quits running and clean lite keeps flashing.


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

Clean lite keeps flashing and will not start a new wash cycle


This may or may not help in your situation, but the following link explains how you may be able to clear the blinking clean light problem: ... Whirlpool DU1055XTS Built-in Dishwasher

Clean lite flashes 7 times and washer will not turn on. Is there a reset sequence? John


Yes there is check under the unit for the tech sheet ... Whirlpool GU2400XTPS Built-in Dishwasher

Replaced handle ok, took panel off to clean. put back only rinse only lite keeps flashing. nothing else responds...


This problem indicates the control mother board needs replacement. Sorry to tell you that. ... KitchenAid Dishwashers

Clean lite flashing - Whirlpool 24 in. DU1055XTP Built-in Dishwasher


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


... Dishwashers

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


You will have to reset the dishwasher. First try and turn off the mains power and back on after a short time. If the clean light flashing starts again then you go through the hard reset procedure. press NORMAL WASH then HEATED DRY buttons on ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0954 seconds