Having problems with your Kenmore 24 in. 16032 Built-in Dishwasher ?

Cannot get lock button to go off

\015 All lights light up including lock button. the dishwasher may run for 15 min. or 1 hour. cannot get it to run a normal cycle. sometimes it comes on and drains and then i can't get it started for several hours.\015

Answers :

1. possible timer issue.
2. motor wear. the motor may be heat protected. if it is worn, or the pump it is attached to is worn, it may overheat. when that happens it shuts off until it cools down. if there are sufficient sensors and boards, some appliances will send information to the timer of an interrupt, which might reset the cycle.
3. drain plugged. if water does not pump out, the rinse cycle will continue to run on many units. this can relate to a general pump problem as well as a plug. inspect the hose for kinks and if it goes to an air gap at the sink, it may be plugged there. lift of the chrome dome, there is a cap at the top of the device you can see once the chrome dome is off. then, put a bowl over the air gap with a towel around the gap on the back side only so the water does not run onto the counter (if you care) and then run the rinse cycle if you can and let the pump out run directly to the sink. that will clear a clog. often clogs come to the top of the air gap, hit the cap and stay there. when you open the cap to inspect, you may not see the plug, as it drops back down the hose until pump is pushing water up the hose again. lawn sprinklers have the same problem sometimes. the clog drops down when you remove the sprinkler to see why its clogged.
mark
Repair Help & Product Troubleshooting for Kenmore 24 in. 16032 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Cannot get lock button to go off


1. possible timer issue.2. motor wear. the motor may be heat protected. if it is worn, or the pump it is attached to is worn, it may overheat. when that happens it shuts off until it cools down. if there are sufficient sensors and boards, some ... Kenmore 24 in. 16032 Built-in Dishwasher

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

I have an old (not sure what year, 80s?) Kitchen Aid energy saver V Custom by Hobart dishwasher. We opened the dishwasher in the middle of a cycle and now cannot get it to re-start. When we lock it back up and push our normal buttons (Low Energy and Energy Saver/Dry Heat Off) or any other combination of buttons, the dial does not turn automatically and the cycle does not continue. I have also tried advancing the dial manually and still, nothing happens. I have even tried advancing it all the


... KitchenAid Dishwashers

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


... Whirlpool GU2400XTP Built-in Dishwasher

Lock Control I don't have a manual for my dishwasher. The Lock button is on (top of dishwasher). I have pushed that top button for 3 seconds. The button on the top and the "L" then both blink. The button on the top then stays on and the "L" light goes off. Since I can't get the lock light to go off - - my dishwasher won't tun on. Thank you very much.


First try unplugging the washer from powerpoint for 30secs..this may disable lock.if not, some washers will still work on lock if you hold the buttons you need. for 5seconds. eg try starting washer as normal but hold the button for 5secs....(Ps you m ... Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher

I have a Frigidaire Gallery Series dishwasher (model. GLD3450RDB0) that always displays the "lock" icon under the no heat dry button. I am able to get rid of it by holding the button for 3 seconds, but I am still unable to select anything or get the dishwasher to start afterwards. As soon as I close the door, the unit locks again! What can I do?


Have you tried unplugging the dishwasher for a while then .. Trying it again.. If the problem still persists have a cleaning done to the control board and touch pad inside and if still the problem persists then i doubt whether the problem is that the ... Dishwashers

Child Lock light glows without pressing Energy Saver Dry button for four seconds. Cannot turn off by pressing Engery Saver Dry button for four seconds. Turning off main power and turning back on doesn't solve problem. But turning off main power for extented period, over night, and turning back on does fix proble for a very short period but Child Lock does come back on by itself. Is replacing the Console Assembly the only fix? Is there some button sequence to disable Child Lock altogher?


The mini manual for this dishwasher is located behind the kick plate. The mini-manual reveals that the child lock (called a control lock in the manual) can be disengaged by pressing and holding the air dry button for four seconds.or ene ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

Our Ikea Nutid Whirlpool dishwasher locked up recently. It started when someone was wiping off the top of the door where the control buttons are located. The dishwasher was locked on the china setting. Holding the cancel button, shutting off the breaker did not seem to clear it. Is there a way to reset the dishwasher? There was flashing on buttons but I cannot remember how many flashes or what one was flashing.


... Whirlpool GU2400XTP Built-in Dishwasher

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

WE HAVE A MAYTAG PLUS DISHWASHER ABOUT 3 YEARS OLD OR LESS. WE WERE GETTING READY TO WASH A LOAD OF DISHES AND THE LOCK BUTTON IS ON AND WILL NOT COME OFF, WE HAVE TRIED PUSHING THE DRAIN OFF BUTTON BUT IT WILL ONLY BLINK, WASHER WILL NOT RUN. LOCK BUTTON WILL BLINK 3 TIMES AND STOP WHAT DO WE DO?


Try holding down the drain button for about 5 seconds.If that still does not do it for you, try taking power from the machine to let it reset itself, easiest is to unplug the unit or flip the breaker switch for the section of the kitchen. ... Dishwashers

[email protected] i cannot get the child lock to turn off and i cannot get the dishwasher to star


Please provide the full model number of our kitchenaid dishwasher.\015\012have you tried turning the power to dishwasher off and back on again from the mains switch.\015\012\015\012Childlock can be turned off by pressing the childlo ... KitchenAid Dishwashers

I would like to get a user manual for LG dishdrawer model DD603, Australian model. Failling that what I really need to know at present is how to use the lock button - just pressing it doesn't seem to work. I need to be able to stop my toddler starting and stopping the dishwasher at her own whim! The front display has three buttons, 'power', LED display then 'Start/pause', & 'lock'. Thanks Shelley


Opps wrong make & model. Searched for fisher & Paykel and found what I needed! No longer need a solution. ... LG Dishwashers

Cannot get Maytag Jetclean Dishwasher-Quiet Plus will not start at all. Push the buttons and get nothing. The circuit breaker is not tripped. Is there a reset button or something like that.


... Maytag Dishwashers

Cannot get my control buttons unlocked. I have a ge profile that is about five years old. I cannot get the heat dry to go off.


Try unplugging the dishwasher and waiting 30 sec and plug back in ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

KUDG25SHBT1 Kitchen Aid dishwasher child lock is on and cant get it off. Pressed and held the start button and now the child lock light is blinking but dont know what to do next?? Please help!! Lexi


... KitchenAid 24 in. KUDS25 Built-in Dishwasher

How do you unlock the locked button on your dishwasher? the locked light is on. can't get it to work.


The solution is very simple.Just press and hold "heated dry" option for five seconds. ... Kenmore Dishwashers

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a Whirlpool gold quiet partner III The type # is 575-0 The model number is GU1200XTL03 The cancel button and the pots and pans button are blinking continuously together. I cannot get it to cancel so I can run the dishwasher. What do I need to do?


Hi.You need to click a button sequence in rapid succession. First perform the steps below:Try first holding down the cancel button. If that does not work, try tripping the circuit breaker for one minute. ... Dishwashers

How do you get the child lock off? New Bosch dishwasher The active, Rinse Agent and Wash light are red, but when you push the start button the Child Lock light come on.


... Bosch Dishwashers

Maytag Quiet Series 800 dishwasher won't start. The only button that I can get to work is pressing and holding the locking feature--that light eventually comes on. A couple of times I came back in an hour or so or the next morning and hit the start button and it started right up. Now it won't start at all. VERY FRUSTRATING!


... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Kenmore Dishwasher Quietguard Standard and it has a little lock icon just below the heat dry button on the front. It is on and I can't start the dishwasher. How do I get the lock off?


Hold down for three to five seconds---or until light shuts off ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1039 seconds