Having problems with your Kenmore 24 in. 16032 Built-in Dishwasher ?

I have a Kenmore mdl. #16032. I have a blinking clean light. Due to this Light or problem the unit will not operate. Prior to this light the dishwasher was a little noisy. What do I need to do to resolve this problem?


Answers :

I think this is related to the wash arm getting obstructed by either a pan or some spoon stuck at the bottom. That could be the noise you mention.
\015\012
\015\012
\015\012I have seen people fix the clean light flashing with a sequence of buttons - see below
\015\012
\015\012push the heated wash,and the heated dry buttons one after the other for about 5 times and all the lights light up and the thing just starts going through different settings then it all quits. Push normal wash and it should work.
\015\012
\015\012Hope this helps.
Repair Help & Product Troubleshooting for Kenmore 24 in. 16032 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore mdl. #16032. I have a blinking clean light. Due to this Light or problem the unit will not operate. Prior to this light the dishwasher was a little noisy. What do I need to do to resolve this problem?


I think this is related to the wash arm getting obstructed by either a pan or some spoon stuck at the bottom. That could be the noise you mention.\015\012\015\012\015\012I have seen people fix the clean light flashing with a sequenc ... Kenmore 24 in. 16032 Built-in Dishwasher

My TEKA Dishwasher DW6 59 F1 starts the cycle makes all the noices but does not heat up & 2 lights light up, i have been told if you locate the reset button, it will resolve the problem?


... Dishwashers

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

I have a Zanussi dishwasher model IT 5614. When I turn the dishwasher on, the indicator light is already stuck at "BIO 50" and won't move, and the dishwasher won't start when the door is closed. This just happened today. The indicator light for dishwasher salt was also on, so I added dishwasher salt and that light went off, but the machine is still stuck. The instruction book says that when this happens, technical assistance is needed. What exactly is the problem, and is it anything I can


It has been suggested to switch the machine on/off a couple of times and the flashing light will not reappear. Until this light goes off the dishwasher will not start. All the filters should be cleaned free of any leftover food particles. What i mean ... Dishwashers

Hi i dont know the model of the dishwasher.. but the controls are fairly staright forward... a little knob for temperatur control and an on/off button.. and a light that lights up green when dishwasher is switched on... now the problem is as happened recently, when you switch the washer on greenlight is on and washer can be heard doing something but after a minuit or so the washer stops and the green light flashes. open up the dishwasher no sign of water or that it has done anything at all... th


It sounds like your washer is not getting enough water to start. If your washing machine is filling too slowly or not at all, then you probably have a clogged screen on the back of your washer. To check this: \015\012\015\012 ... Whirlpool Dishwashers

I'm having a problem with my Miele dishwasher G 879 SCVi I asked for assistance on 2/12/10 and paid $6.00. I have yet to get a response. Please let me know when I will as I need the problem addressed before Christmas Day. The problem again is that all the lights on the diswasher panel are all flashing at the same time when switched on. It may need to be reset somehow, as the power went off, which may have caused the problem. Your urgent assistance is required. Thank you


... Dishwashers

We just bought this dishwasher. The instructions say it doesn't need to be anchored and it doesn't come with the clips you usually see for dishwashers that need to screwed into the frame (or have a place where such clips could be attached). That said, the dishwasher completely tilts forward when the top rack is loaded, so something is definitely not right. Has anyone had this problem and/or know how to resolve? Thanks.


... Maytag MDBH985AWW 24 in. Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Whirlpool GU2400XTPT Dishwasher is on island of Utila, Honduras. Upon return after several months absence, light was flashing but dishwasher would not turn on, light would not turn off, no other buttons would light up. I am thinking a power surge might have hit it and maybe knocked something out. Problem is, I need a part from here to take down there and hope someone there can install it. Help! Thanks! Barbara Chaney


I had a svc. tech come and he said I need a new "panel". Darn.It's $133 plus labor. He said the "normal" button had shorted out,especially since that's the wash I use all the time. It's only two years old, and I didn't buy an extended w ... Whirlpool GU2400XTP Built-in Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Asko D3120 I have resolved the problem of pum always running by tilting the dishwasher but now I have a new problem of the pump not draining the water in the bottom of the dishwasher. I thought it was clogged so I removed the screen and filters but did not stick my hand in the hole to clean... I used the plunger for at least 30 mins. Then I tried to pour a little CLR because I have hard water. NOTHING please help me


In the bottom where the filter are, you can see a yellow 'thing'. Remove this and stick one finger in an try to rotate the pump wing. Try to remove particals that is blocking the pump.\015\012Or there is something in the drain hose. Try to drai ... Asko 24 in. D3120 Dishwasher

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

Intake drain The dishwasher is an excellent machine but the intake drain problem is driving us crazy. I have had pumps changed twice and that has not been the problem. I start the dishwash and within a minute the intake drain light comes on right after the first cycle. I need help!!


... Miele 24 in. Touchtronic Platinum Built-in Dishwasher

Hi Have a built in AEG OKO Favorit slim dishwasher (can't find exact model no). Problem is that dishwasher tablet dispenser does't open and after 5 minutes get 5 lots of 2 beeps. When I open the dishwasher, the Rinse/Hold, Intensive, and Normal lights are all flashing. Do I need to get an engineer out? Thanks


HI there,If that\015\012lever is broken or in some way defective, it will need to be replaced. As well as controlling cycle times, the timer on many\015\012dishwashers also functions as an actuator for the spring-loaded\015\0 ... Dishwashers

Salt Light Cannot get the salt light to go out. Had some problems with a crystaline Deposit on the left side of machine. we checked the inside of the dishwasher and made sure all was clean etc. After that the light wouldn't go out. Had machine serviced. Turns out we were using too much diswashing powder Only need to use about a Teaspoon (heaped) for a wash not the recptacle full.


The sensor in the salt chamber isn't reading properly. Try descaling the machine with solution and restarting. ... Miele Dishwashers

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

3 PROBLEMS 1. SPRAYER ARM LIGHT ON BUT WHEN I OPEN THE DISHWASHER THERE IS NOTHING BLOCKING THE ARM FROM SPINNING. 2. SALT LIGHT IS ALWAYS ON. HOW DO I ADD SALT. 3. I NEED NEW TRIM FOR THE OUTSIDE OF THE WASHER. WHERE CAN I GET THAT. OH ONE MORE 4. IS THERE A WAY TO HAVE THE WASHER SERVICED SO I KNOW IT'S IN GOOD WORKING ORDER. LIKE A CAR TUNE UP? WHO DO I CALL? THANKS!


This is just to let you know that the internal water softener needs water-softener salt. If you do not use the softener (I do not at my house) then the light serves as a convenient on/off light.The other issues you have can ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

My Kenmore ultra wash dishwasher fills with a little bit of water but does not spray water and does not proceed through the wash cycle. Any advice? We had problems yesterday with blinking lights and not able to get anything to work except the drain. then we followed a sequence of pushing buttons and it solved the first problem.


The spray arm rotates based on the water pressure coming out of them. If no water pressure, then no rotation. You probably have a clog on the intake hose. You can pull out the dishwasher, tip it forward so you can get to the bottom and then rem ... Kenmore Dishwashers

I have GU2548XTPS Built-in Dishwasher. I need to reset this. When I start my dishwasher, display shows "2". After 2 minute display is "- -" Last time I found some code from internet and it worked. Could you help me to resolve this problem? Thanks, Dinesh Gondaliya


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

We have jp-24B series dishwasher it was doing great until about 2 months ago and the glasses come out all spotty. The dishwasher seems to be running through all the cycles and it gets up to temperature but the glasses have all thses lines when the water drains out of the glasses and spots, a light chaulky color. We have ran the dishes for 2 or 3 cycles and it helps a little bit. What is the problem?


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Jackson JP-24B Built-in Dishwasher

My dishwasher (indestit) will not fill up with water. A technian came today and advise that there was very little water coming through the hose and therfore had a blockage. I replaced it today and it fixed the problem, however onn the 1st wash the cycle appeared to stop rather than completing fully. I have since tried to restart and have the same problem lights 2 and 3 are flashing indicating there is no water getting through, how can this be.


Hi,Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have a hotpoint HDA2000G00WW built in dishwasher. The dishwasher does not run unless you press the plastic door under the latch area. I have adjusted the latch and that does not resolve the problem. I notice that the top three screws that hold the plastic eschucion are no longer holding as the plastic screw areas have broken on the eschucion. Do I need to replace the eschucion or can it be tightened some other way?


... Hotpoint 24 in. HDA2000Z Built-in Dishwasher

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

Our Maytag model MDB4010AWW (8 1/2 years old) is leaving food stuck on the dishes and glasses on the top rack consistently. We've run several bottles of Dishwasher Magic through in the past few weeks which has only helped the problem a little. We posted this question to a similar forum a few weeks ago, and it was suggested that the wash pump might need replacement. What's the average life expectancy of a lowend dishwasher like ours? would it be more cost effective to replace it rather than to sp


It would cost you at least the 200.00 to have it replaced since the pump cost 150.00 and you would have labor added. It should last longer than it did if that's what's wrong with it. I would first observe to see if the upper spray arm is spinning and ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1834 seconds