Having problems with your Kenmore 24 in. 16034 Built-in Dishwasher ?

The water will not drain after the wash and rinse cycle have ended. Serial # SR3701411 Model # 665.16034400 Cybe # 565-D


Answers :

\015\012Why the Dishwasher Won't Drain?

In this section, we are trying to figure out all the possible causes behind the problem. We are also providing you with some solution to fix each one of those problems:

Reason#1: The most common reason behind improper draining of dishwasher is clogging of the household drain under the kitchen sink. Observe the dishwasher carefully while it is draining. If you find that water bubbles are coming up into the sink, then it is likely that the problem lies with the drain pipe and not the machine. Detach the drain pipe from the kitchen sink and clear out all the debris that are causing the clogging and reattach it. Also check the pipe that connects the dishwasher and the sink and remove if there is any trash left. Know more on unclog kitchen sink.

Reason#2: If the door latch of the dishwasher is not working properly, then the door cannot be closed and the dishwasher is not going to drain the water fully. Check out if the latch has become loose or gone out of alignment. In such cases, tightening the bolts of the latch will help in fixing the problem.

Reason#3: Accumulation of food particles in the dishwasher basket can prevent the water from flowing out of the drain. In that case, you have to disassemble the dishwasher basket and clean all its parts thoroughly to get rid of the gunk matter. Then reassemble the basket and you will find the drain is cleared. You can do this repair work on your own if you have some knowledge about the dishwasher parts. Take the help of user's manual provided by the manufacturer to find out the right technique to open the basket of the specific model that you have.

Reason#4: A new garbage disposal device can be responsible for this kind of trouble. This will happen if you have recently installed a garbage disposal and have not removed the knock out plug from it, then the dishwasher won't drain water. Once you remove the plug, it will ensure that the water from the dishwasher goes directly into the disposal for draining. Clogged garbage disposal can also trigger this type of trouble. Running the garbage disposal with plenty of hot water can clear such obstructions.

Other Reasons: In case all the above mentioned techniques fail to show desired results, then the defect could be something more serious and is related to some of the other parts of the dishwasher. Problems related to the drain valve, timer, belt, pump or motor and may require replacement with a new one. The part to be replaced has to be chosen very carefully and it should be right for the specific model that you have. It is better if you do not try to fix such things on your own and consult a repair professional who have the skills to handle these problems more effectively. You may even land up in trouble with the warranty of the appliance if you install any wrong part in your model. Know more ondishwasher not draining.

Now you are aware of the factors for which the dishwasher won't drain. After the troubleshooting, run some hot water thought the garbage disposal to clear any residue of dirt and grease from the pipes. Then start running the dishwasher. You can prevent such problems in future by running some vinegar through the dishwasher once or twice a month. If you live in an area where you get hard water, then clean the sink drain with a drain cleaner to keep it free from mineral deposits.\015\012\015\012\015\012
Repair Help & Product Troubleshooting for Kenmore 24 in. 16034 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

I have a candy trio 501 dishwasher with intergrated oven. When I put a cycle on it starts its first rinse then after 5/10 mins stops and beeps constantly. It's still full of water too. When I put it on rinse cycle it compleates the cycle so inlet and drainage should be ok. Ive removed drain pipe and made sure its not kinked and also clear. I've removed and drained the compartments that had water in and also blew down the pips to see if clear all ok. I've checked the heater element with meter and


... Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

The dishwasher stops at the rinse cycle, does not drain and then the Quick Rinse button is the only cycle that will light up. Sometimes I can get the washer to choose a different cycle... but it is about every third day. And once the load gets to the rinse cycle, it starts all over again.


... Kenmore 13593 Stainless Steel Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

Sometimes the dishwasher drains, sometimes it doesn't; I emptied the dishwasher, removed the bottom tray and baskets; ran a cycle - it drained so, I presumed it was now operating as it should - it wasn't - the tub was full of water so, I ran a rinse (5 minutes) cycle - it drained next time I ran a cycle - it didn't drain


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain out ... GE Nautilus 24" Built-in Dishwasher

My GE dishwasher drains fine after wash cycles. However, After rinsing, about 2 inches of water is left in the tub. The drain runs for 30-35 seconds at the end of each wash cycle, but only 4-5 seconds after the rinse. What do I need to do to fix this?


Many dishwashers use a drain valve with an electric solenoid. When electricity flows to the solenoid, the valve opens and diverts the water to the drain. Sometimes the solenoid, or the diverting lever, sticks and prevents the dishwasher from dr ... Dishwashers

Why does the unit fail to drain after rinse cycle? The problem is intermittent, sometimes it works, sometimes it doesn't. When trying to force it to drain, we do another rinse cycle and, again, sometimes it works, sometimes not. The model is GE GSD5200G00WW


This is a really common problem that most people send hundreds when they can fix it themselves. Power off your washer, put it on its side. Your going to see four to six silver bolts with hex heads located in the center holding in a plastic devi ... GE 24 in. GSD5200 Built-in Dishwasher

The machine fills ,drains and washes as normal. However when it fills the wash temp is 60 as normal but the rinse temp wont go higher than 76 deg C . when the wash cycle is on , the cycle stays on wash not progressing thru drain and rinse What is the cause?


Hello. Let me assist you. There are only two reasons for your problem - if you can isolate your problem based upon these descriptors you will know which part to replace:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-he ... Dishwashers

Bosch dishwasher SHE44C02UC, serial # 13693156: Does not cycle. I turn off and drain by pressing "Regular Wash" and "Rinse and Hold" together (need several of these to completely drain), then rinse by starting cycle and repeating above sequence. Slight burning smell also - motor? Is there a way to initialize the sequence, and if there is, is it advisable, given the slight smell? Robert Langridge


Hi\015\012\015\012First, try to hear a hum like sound from the motor however, the burning smell indicates that the motor is unable to work. You can also check that the motor is work ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Miele G843SCVI will not drain. It will however drain on Rinse and Hold. Have cleaned filter, non return valve and checked lines. The failure to drain is intermittent. Sometimes it drains. Type of wash cycle does not matter except rinse and hold which does drain. Is there any other solution?


\015\012\011From the excellent description you give the most likely cause of this problem is the check ball and funnel in the soil collector.It drains fine sometimes but sometimes it doesn't drain but the motor is turning. ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

I cannot figure out how to advance a cycle without having to go through the entire cycle. For example, I had a drain problem with my sink and the plumber put the rinse and hold cycle on for about 10 minutes; now every time I want to turn on the dishwasher it is in the rinse and hold cycle. How can I change it???


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Your post doesn`t specify a model number, however on most Bosch dishwashers in order to change from "rinse & hold" to "regular" ( or any cycle ) simply turn t ... Bosch Dishwashers

GE Nautilus won't drain after Rinse Cycle


Check disposer plug. If a garbage disposer has been recently installed, it is possible the disposer drain plug was not removed. The drain plug is a plastic piece in the disposer that blocks the hole where the dishwasher hose connects. Also che ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

Our moffat quiet 2 dishwasher has recently developed the problem that the dishes are not cleaned properly. It does drain water. We've opened the drain cover to check that. There does not seem to be a problem there. We've also started hearing a buzzing sound that lasts a minute or so between cycles. (Not between every cycle though) It's random. We rinse our dishes thoroughly before running a cycle. This unit is approx. 5 years old. Any suggestions?


Check to make sure there are no obstructions blocking the washer heads from spinning. ... Dishwashers

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Slow drain. My dishwasher is draining, but not enough to empty the water out after a normal cycle. This is also causing the rinse cycle to use recycled dirty water in the process. I've check the lines and there are no blockages there. Inside the dishwasher are 2 little white balls...where is the exact position they should be placed? Could this be blocking some of the draining process?


... Kenmore 24 in. 15652 Built-in Dishwasher

Hi. After completing the wash and rinse cycles, my Frigidare FDB750RC dial stays stuck just before begining the drain and drying cycle. If I turn it one click, then it drains and finshes drying cycle fine.


... Frigidaire 24 in. FDB750RC Slim-Line Built-In Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Hello, I've got a Bosch dishwasher that is acting really funny. I've had it for 4 years. It's 630 SHE44C06UC model. It powers and I hear it run, but the cycle ends w/ 1 but it runs forever...and doesn't rinse or drain. Cancel drain works, but there are spots. I have rinse agent, it fills, drains, etc. I'm wondering if someone knows how I could reset it before calling a repair man? It doesn't seem to dry either? Any help? Thanks, Steph


Hello,Welcome to FixYa.Based on your description I'd say the issue is with the control...unfortunately.The number"1" being displayed ( on models with ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Dishwasher doesnt drain on wash cycle,ok on rinse cycle


Change the circuit board, timer/progrsmer. \015\012Take it out and clean contacts,\015\012Look for burnt circuit line and solder a fine bead carefully on the circuit board, difficult. Use the pot and pan program.\015\012Vitally ... Maytag MDB7100AWB Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1508 seconds